HP 3000 Manuals HP 3000 Manuals
(Subsystem 148) (contd)
---------------------------------------------------------------
260 MESSAGE An error was received from SENDIO reading sector
from save area.
CAUSE Error returned from SENDIO for sparing read sector
for restore sector.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
261 MESSAGE An error was received from RENDEZVOUSIO writing
sector to new home.
CAUSE Error returned from RENDEZVOUSIO for sparing write
sector for restore.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
262 MESSAGE An error was received from SENDIO writing sector
to new home.
CAUSE Error returned from SENDIO for sparing write sector
for restore sector.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
263 MESSAGE An error was received from SENDIO reading sector
from track.
CAUSE Error returned from SENDIO for sparing read sector
save track.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
264 MESSAGE An error was received from SENDIO writing sector
to save area.
CAUSE Error returned from SENDIO for sparing write sector
save track.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
265 MESSAGE An error was received from SENDIO reading sector
from track save area.
CAUSE Error returned from SENDIO for sparing read sector
for restore track.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
266 MESSAGE An error was received from RENDEZVOUSIO writing
sector to new home.
CAUSE Error returned from RENDEZVOUSIO for sparing write
sector for restore track.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
267 MESSAGE An error was received from SENDIO writing sector
to new home.
CAUSE Error returned from SENDIO for sparing write sector
for restore track.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
268 MESSAGE This is a bad SECTOR TABLE index error.
CAUSE Internal error. Error in sector state in bad
sector table.
ACTION Retry the function (INSTALL, UPDATE, START or mount
volume). Write over sector zero to bypass sparing
on this volume and initialize it again. Call your
Hewlett-Packard Representative.
---------------------------------------------------------------
269 MESSAGE An error was received from SENDIO running sector
test.
CAUSE Error returned from SENDIO for sparing run sector
test.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
270 MESSAGE This is an internal error; error in track start
address.
CAUSE Internal debug error. Not released. Invalid
sector number from caller for run track test.
ACTION Call your Hewlett-Packard Representative.
---------------------------------------------------------------
271 MESSAGE An error was received from SENDIO running track
test.
CAUSE Error returned from SENDIO for sparing run track
test.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
272 MESSAGE An error was received from SENDIO running R.O.
track test.
CAUSE Error returned from SENDIO for sparing run R.O.
track test.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
273 MESSAGE An error was received from SENDIO running
controller test.
CAUSE Error returned from SENDIO for sparing run
controller test.
ACTION Call your Hewlett-Packard Representative.
---------------------------------------------------------------
274 MESSAGE This is an invalid sector address.
CAUSE Internal debug error. Not released. Invalid
sector number from caller for run track test.
ACTION Call your Hewlett-Packard Representative.
---------------------------------------------------------------
275 MESSAGE An error was received from RENDEZVOUSIO sparing a
sector.
CAUSE Error returned from RENDEZVOUSIO for sparing spare
sector.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
276 MESSAGE An error was received from SENDIO sparing a
sector.
CAUSE Error returned from SENDIO for sparing spare
sector.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
277 MESSAGE This is an internal error in sector state.
CAUSE Internal error. Error in sector state in bad
sector table.
ACTION Retry the function (INSTALL, UPDATE, START or mount
volume). Write over sector zero to bypass sparing
on this volume and initialize it again. Call your
Hewlett-Packard Representative.
---------------------------------------------------------------
278 MESSAGE An error was received from SENDIO sparing a
track.
CAUSE Error returned from SENDIO for sparing spare track.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
282 MESSAGE A failure occurred from RENDEZVOUSIO skipping
forward a tape file.
CAUSE Error returned from RENDEZVOUSIO for skip tape
file.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
283 MESSAGE A failure occurred from SENDIO skipping forward a
tape file.
CAUSE Error returned from SENDIO for skip tape file.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
284 MESSAGE A failure occurred from RENDEZVOUSIO rewinding
tape.
CAUSE Error returned from RENDEZVOUSIO for rewind tape.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
285 MESSAGE A failure occurred from SENDIO rewinding tape.
CAUSE Error returned from SENDIO for rewind tape.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
286 MESSAGE A failure occurred from RENDEZVOUSIO unloading a
tape.
CAUSE Error returned from RENDEZVOUSIO for unload tape.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
287 MESSAGE A failure occurred from SENDIO unloading a tape.
CAUSE Error returned from SENDIO for unload tape.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
288 MESSAGE A failure occurred from RENDEZVOUSIO reading file
label from tape.
CAUSE Error returned from RENDEZVOUSIO for read tape file
label. Possible tape read error.
ACTION Determine cause of error from RENDEZVOUSIO and
correct. Clean tape drive and retry. Clean tape
drive, remake tape and retry.
---------------------------------------------------------------
289 MESSAGE A failure occurred from SENDIO reading file label
from tape.
CAUSE Error returned from SENDIO for read tape file
label.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
290 MESSAGE Not enough data was read from tape reading the
file label.
CAUSE Tape read expected 256 bytes and got less than 200
bytes. Possible tape read error or tape position
error.
ACTION Clean tape drive and retry. Clean tape drive,
remake tape and retry.
---------------------------------------------------------------
291 MESSAGE A failure was received from RENDEZVOUSIO skipping
backwards on tape.
CAUSE Error returned from RENDEZVOUSIO for skip record
back.
ACTION Determine cause of error from RENDEZVOUSIO and
correct.
---------------------------------------------------------------
292 MESSAGE A failure was received from SENDIO skipping
backwards on tape.
CAUSE Error returned from SENDIO for skip record back.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
293 MESSAGE A second NL.PUB.SYS was found on the boot tape.
CAUSE A second NL.PUB.SYS file was found on the tape.
Invalid tape format. File is identified by start
number in tape file header.
ACTION Determine the cause of the extra NL.PUB.SYS file
and correct. Remake the tape and redo the UPDATE
or INSTALL.
---------------------------------------------------------------
294 MESSAGE Can not purge NL.PUB.SYS from disk.
CAUSE Error returned from HPOPEN for create of
NL.PUB.SYS. File is identified by start number in
tape file header.
ACTION Determine cause of error from HPOPEN and correct.
---------------------------------------------------------------
296 MESSAGE A failure occurred from RENDEZVOUSIO reading user
label block.
CAUSE Error returned from RENDEZVOUSIO for read user
label block of a system file.
ACTION Determine cause of error from RENDEZVOUSIO and
correct. Clean tape drive and retry. Clean tape
drive, remake tape and retry.
---------------------------------------------------------------
297 MESSAGE Length error reading user label block.
CAUSE EOF read from tape while reading user label data.
Invalid tape. Possible tape read error or tape
position error.
ACTION Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and
retry.
---------------------------------------------------------------
298 MESSAGE A failure occurred from SENDIO reading user label
block.
CAUSE Error returned from SENDIO for read user label
block.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
299 MESSAGE An error occurred from FWRITELABEL writing user
label.
CAUSE Condition code error returned by FWRITE for user
label block.
ACTION Determine cause of error from FWRITE and correct.
---------------------------------------------------------------
300 MESSAGE A failure occurred from RENDEZVOUSIO reading
system file block from tape.
CAUSE Error returned from RENDEZVOUSIO for read file
block. Possible tape read error or tape position
error.
ACTION Determine cause of error from RENDEZVOUSIO and
correct. Clean tape drive and retry. Clean tape
drive, remake tape and retry.
---------------------------------------------------------------
301 MESSAGE This is a premature EOF on tape reading the
system file block.
CAUSE An EOF was read from the tape before expected while
reading system file data. Invalid tape. Possible
tape read error or tape position error.
ACTION Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and
retry.
---------------------------------------------------------------
302 MESSAGE A failure was received from SENDIO reading system
file block.
CAUSE Error returned from SENDIO for system file block.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
303 MESSAGE An error occurred from FWRITE on system file
block.
CAUSE Condition code error returned by FWRITE for file
data block.
ACTION Determine cause of error from FWRITE and correct.
---------------------------------------------------------------
304 MESSAGE An error occurred from FCLOSE on system file.
CAUSE Error from FCLOSE for system file.
ACTION Determine cause of error from FCLOSE and correct.
---------------------------------------------------------------
305 MESSAGE There is an error in the number of blocks on tape
for system file; file length error.
CAUSE Record count error from tape while reading system
file data. Invalid tape. Possible tape read error
or tape position error.
ACTION Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and
retry.
---------------------------------------------------------------
306 MESSAGE HPOPEN error occurred for DUMPAREA.
CAUSE Error returned from HPOPEN for create of
DUMPAREA.MPEXL.SYS.
ACTION Determine cause of error from HPOPEN and correct.
---------------------------------------------------------------
307 MESSAGE An error was received from FWRITE for DUMPAREA.
CAUSE Condition code error returned by FWRITE for
DUMPAREA.MPEXL.SYS.
ACTION Determine cause of error from FCLOSE and correct.
---------------------------------------------------------------
308 MESSAGE Error from FCLOSE for DUMPAREA.
CAUSE Error from FCLOSE for DUMPAREA.MPEXL.SYS file.
ACTION Determine cause of error from FCLOSE and correct.
---------------------------------------------------------------
310 MESSAGE An error was received from HPOPEN for creating
boot file.
CAUSE Error returned from HPOPEN for create of a boot
file.
ACTION Determine cause of error from HPOPEN and correct.
---------------------------------------------------------------
311 MESSAGE An error occurred on reading the tape boot file
block.
CAUSE Error returned from SENDIO for read file block from
tape.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------
312 MESSAGE There was an error in the number of blocks on the
tape for the boot file; file length error.
CAUSE User label numbers in tape file label are
incorrect. Invalid tape format. User labels are
invalid for a boot file.
ACTION Determine cause of incorrect numbers and correct.
Remake tape and retry the UPDATE or INSTALL.
---------------------------------------------------------------
313 MESSAGE An error was received from FWRITE on the boot
file.
CAUSE EOF read from tape before expected while reading
boot file data. Invalid tape. Possible tape read
error or tape position error.
ACTION Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and
retry.
---------------------------------------------------------------
314 MESSAGE Failure posting page 1 to disk.
CAUSE Error from LOAD_POST writing to sector zero and one
of LDEV 1.
ACTION Determine cause of error from LOAD_POST and
correct.
---------------------------------------------------------------
315 MESSAGE An error was received from FCLOSE of boot file.
CAUSE Error from FCLOSE for a boot file.
ACTION Determine cause of error from FCLOSE and correct.
---------------------------------------------------------------
316 MESSAGE The procedure failed to add boot file to the LIF
directory.
CAUSE Error returned from ADD_NEXT_DIR_ENTRY for a boot
file while attempting to add an entry to the LIF
directory.
ACTION Determine cause of error from ADD_NEXT_DIR_ENTRY
and correct.
---------------------------------------------------------------
317 MESSAGE There was an error in the number of blocks on
tape for the boot file; file length error.
CAUSE Record count error from tape while reading boot
file data. Invalid tape. Possible tape read error
or tape position error.
ACTION Determine cause of error and correct. Clean tape
drive and retry. Clean tape drive, remake tape and
retry.
---------------------------------------------------------------
318 MESSAGE An error was received from RENDEZVOUSIO reading
first label from tape.
CAUSE Error returned from RENDEZVOUSIO for read labels.
First read from the tape. Possible tape read error
or tape position error.
ACTION Determine cause of error from RENDEZVOUSIO and
correct. Clean tape drive and retry. Clean tape
drive, remake tape and retry.
---------------------------------------------------------------
319 MESSAGE An error was received from SENDIO reading the
first label from the tape.
CAUSE Error returned from SENDIO for read labels. First
read from the tape.
ACTION Determine cause of error from SENDIO and correct.
---------------------------------------------------------------