HP 3000 Manuals HP 3000 Manuals
MPE V SNA Transport Error Messages (SNAERR)
The following SNA Transport messages can appear on Pass Thru devices or,
in some cases, the system console.
---------------------------------------------------------------------------------------
SNAERR 1 MESSAGE Illegal DB register. (SNAERR 1)
CAUSE The DB register was pointing to an extra data segment on
a call to an SNA Link intrinsic.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 2 MESSAGE Invalid session. (SNAERR 2)
CAUSE You probably passed an SNA IMF intrinsic an invalid
terminal identifier parameter.
ACTION Be sure you used the terminal identifier returned by
OPEN3270.
---------------------------------------------------------------------------------------
SNAERR 3 MESSAGE Invalid SNA catalog file. (SNAERR 3)
CAUSE The parameter was omitted on a call to an SNA Link
intrinsic.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 4 MESSAGE Security violation. (SNAERR 4)
CAUSE You tried to invoke Pass Thru by specifying a class name
that you were not authorized to use.
ACTION Specify a class name that you are authorized to use.
Check with your system administrator to determine which
classes are available. This can be determined by the
user and program.
---------------------------------------------------------------------------------------
SNAERR 5 MESSAGE Parameter bounds violation. (SNAERR 5)
CAUSE SNA IMF passed SNA Link an out-of-bounds parameter.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 6 MESSAGE Invalid flag parameter. (SNAERR 6)
CAUSE SNA IMF passed an invalid flag parameter to an SNA Link
intrinsic.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 7 MESSAGE Session is active. (SNAERR 7)
CAUSE The NAU has been activated.
ACTION None.
---------------------------------------------------------------------------------------
SNAERR 8 MESSAGE Session is inactive. (SNAERR 8)
CAUSE You attempted to send data on the LU-SSCP session, but
the LU had not been activated by the host.
ACTION Try again after the node has been activated from the host
side.
---------------------------------------------------------------------------------------
SNAERR 9 MESSAGE No available AFT entry. (SNAERR 9)
CAUSE There were not enough available file table (AFT) entries
in the process control block extension for SNA IMF to
complete the initialization for the Pass Thru session.
ACTION Too many files may have been opened by your program; try
again.
---------------------------------------------------------------------------------------
SNAERR 10 MESSAGE Bad PI in RH. (SNAERR 10)
CAUSE Invalid Pacing Indicator in Request/Response Header.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 11 MESSAGE Bad BCI in RH. (SNAERR 11)
CAUSE Invalid Begin Chain Indicator in Request/Response Header.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 12 MESSAGE Bad ECI in RH. (SNAERR 12)
CAUSE Invalid End Chain Indicator in Request/Response Header.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 13 MESSAGE Bad EDI in RH. (SNAERR 13)
CAUSE Invalid Enciphered Data Indicator in Request/Response
Header.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 14 MESSAGE Reserved bits in RH must be set to zero. (SNAERR 14)
CAUSE SNA IMF failed to initialize reserved bits in the
Request/Response Header.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 15 MESSAGE Internal Error. (SNAERR 15)
CAUSE An internal error has occurred in the SNA Link software,
most likely causing the node to shut down.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 16 MESSAGE Invalid RU size. (SNAERR 16)
CAUSE SNA IMF passed an SNA Link intrinsic an RU which exceeded
the allowable size for this session.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 17 MESSAGE NAU is inactive. (SNAERR 17)
CAUSE The NAU is not active.
ACTION Ensure that the NAU has been activated on the host side.
---------------------------------------------------------------------------------------
SNAERR 18 MESSAGE Invalid Plabel. (SNAERR 18)
CAUSE The SNAControl intrinsic was passed an invalid PLabel by
SNA IMF.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 19 MESSAGE LU-SCCP message pending. (SNAERR 19)
CAUSE A message on the LU-SSCP session is pending and must be
completed before proceeding further.
ACTION Issue a call to RECV3270 before proceeding.
---------------------------------------------------------------------------------------
SNAERR 20 MESSAGE RU buffer too small. (SNAERR 20)
CAUSE The RU size used by SNA IMF is too small to contain the
data to be returned by SNA Link.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 21 MESSAGE Invalid class name. (SNAERR 21)
CAUSE You specified an invalid class name in the Pass Thru info
string, or the class is not associated with the specified
node.
ACTION Invoke Pass Thru and specify a correct class name. Check
with your system manager for the valid classes configured
in the configuration file for the requested node name.
---------------------------------------------------------------------------------------
SNAERR 22 MESSAGE Invalid session type. (SNAERR 22)
CAUSE An invalid session type parameter was passed to SNA Link.
ACTION Note the circumstances and report them to your HP
representative.
Table A-0. (cont.)
---------------------------------------------------------------------------------------
SNAERR 23 MESSAGE Negative LU-SSCP response. (SNAERR 23)
CAUSE A negative response occurred on the LU-SSCP session.
ACTION Make sure the IBM host application that you are trying to
access is operational. If it is, note the circumstances
and contact your HP representative.
---------------------------------------------------------------------------------------
SNAERR 24 MESSAGE Invalid configuration access. (SNAERR 24)
CAUSE The node manager (NMMGR) configuration file name
(NMCONFIG) is incorrect, or the file is corrupt or
missing. The SNA Link software encountered an error
accessing data in the configuration file, so SNA IMF
could not start the Pass Thru session.
ACTION Have the system manager verify the accuracy of the
configuration file, and try again.
---------------------------------------------------------------------------------------
SNAERR 25 MESSAGE Request pending. (SNAERR 25)
CAUSE A request is already pending.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 26 MESSAGE No available NAU. (SNAERR 26)
CAUSE All the NAUs configured in the SNA class specified in the
info string are currently in use.
ACTION Try again later when the system is less busy, or specify
another class name if one is configured.
---------------------------------------------------------------------------------------
SNAERR 27 MESSAGE I/O pending. (SNAERR 27)
CAUSE A previous I/O request has not been completed.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 28 MESSAGE Invalid function code. (SNAERR 28)
CAUSE SNA IMF passed SNA Link an invalid function code
parameter.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 29 MESSAGE Inactive node or invalid node name. (SNAERR 29)
CAUSE You specified an invalid node name in the Pass Thru info
string, or the node you specified has not been activated
on the HP 3000.
ACTION Verify the accuracy of the info string and check with the
system manager to make sure the node you specified has
been activated on the HP 3000.
---------------------------------------------------------------------------------------
SNAERR 30 MESSAGE Illegal call. (SNAERR 30)
CAUSE SNA IMF and SNA Link are not synchronized with respect to
the type of session established.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 31 MESSAGE Invalid error code. (SNAERR 31)
CAUSE SNA IMF passed SNAErrMsg an invalid error code parameter.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 32 MESSAGE Privilege mode required. (SNAERR 32)
CAUSE An SNA Link intrinsic was called that required Privilege
Mode capability.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 33 MESSAGE Invalid InfoWanted parameter. (SNAERR 33)
CAUSE SNA IMF passed SNASessInfo an invalid InfoWanted
parameter.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 35 MESSAGE No request pending. (SNAERR 35)
CAUSE There are no requests pending.
ACTION None.
---------------------------------------------------------------------------------------
SNAERR 36 MESSAGE Link shutdown occurred. (SNAERR 36)
CAUSE The node that you specified in the info string when Pass
Thru was invoked has been shut down. An SNACONTROL STOP
command was issued or a link error has occurred; your
session has been terminated.
ACTION Try again later when the HP 3000 node has been
reactivated with the SNACONTROL START command.
---------------------------------------------------------------------------------------
SNAERR 37 MESSAGE Protocol shutdown requested. (SNAERR 37)
CAUSE The node on which you are running has been shut down by
the system manager with the SNACONTROL STOP command.
ACTION Try again later when the HP 3000 node has been
reactivated with the SNACONTROL START command.
---------------------------------------------------------------------------------------
SNAERR 38 MESSAGE Quiesce shutdown requested. (SNAERR 38)
CAUSE The node on which you are running has been shut down by
the system manager with the SNACONTROL STOP command. The
SNA node is being restrained from starting new jobs. As
current jobs finish, the system gradually winds down
until jobs are no longer running.
ACTION Try again later when the HP 3000 node has been
reactivated with the SNACONTROL START command.
---------------------------------------------------------------------------------------
SNAERR 39 MESSAGE Invalid parameters. (SNAERR 39)
CAUSE The message catalog CATSNA.PUB.SYS is invalid.
ACTION Inform your system manager.
---------------------------------------------------------------------------------------
SNAERR 40 MESSAGE No stack space. (SNAERR 40)
CAUSE The SNA Link subsystem could not process a request made
by the SNA IMF Pass Thru process due to insufficient
stack space.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 41 MESSAGE Invalid request. (SNAERR 41)
CAUSE Invalid request.
ACTION Try again later.
---------------------------------------------------------------------------------------
SNAERR 42 MESSAGE Invalid trace element. (SNAERR 42)
CAUSE An invalid trace element was encountered by SNA Link.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 43 MESSAGE Invalid trace state. (SNAERR 43)
CAUSE An invalid trace state was encountered by SNA Link.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 44 MESSAGE Invalid subclass. (SNAERR 44)
CAUSE SNA Link encountered an invalid subclass.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 45 MESSAGE Invalid entry. (SNAERR 45)
CAUSE An invalid entry was detected by SNA Link.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 46 MESSAGE Maximum data too small. (SNAERR 46)
CAUSE SNA IMF passed SNA Link an invalid MaxData parameter.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 47 MESSAGE Invalid action code. (SNAERR 47)
CAUSE SNA IMF passed SNA Link an invalid ActionCode parameter.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 48 MESSAGE Invalid data offset. (SNAERR 48)
CAUSE SNA IMF passed SNA Link an invalid data offset parameter.
It was probably negative or longer than the length of the
message.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 49 MESSAGE Invalid FunctionParm. (SNAERR 49)
CAUSE SNA IMF passed SNAControl an invalid function parameter.
Legal values range from 0 through 6.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 50 MESSAGE Invalid buffer length. (SNAERR 50)
CAUSE SNA IMF passed an invalid buffer length to an SNA Link
intrinsic.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 51 MESSAGE Link Failure occurred. (SNAERR 51)
CAUSE The node on which you are running has shut down due to a
link failure, and your session has been terminated.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 52 MESSAGE Transport Internal Error Shutdown. (SNAERR 52)
CAUSE The SNA Link software has encountered an internal error,
and the node has been shut down.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 53 MESSAGE Hierarchical Shutdown. (SNAERR 53)
CAUSE The host has deactivated your NAU, so your session has
been terminated.
ACTION Try again after the host has reactivated the NAU, or
contact the IBM system manager to have the NAU
reactivated.
---------------------------------------------------------------------------------------
SNAERR 55 MESSAGE Bad Maxinfo length parameter. (SNAERR 55)
CAUSE SNA IMF passed SNA Link an invalid MaxInfoLength
parameter.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 100 MESSAGE Expedited response pending. (SNAERR 100)
CAUSE An expedited response is pending and must be completed
before proceeding.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 101 MESSAGE Data traffic inactive. (SNAERR 101)
CAUSE The host has not sent the necessary command sequence to
activate your session.
ACTION Check with your system administrator or IBM operator to
make sure the NAUs on the HP 3000 have been properly
activated, then try again.
---------------------------------------------------------------------------------------
SNAERR 102 MESSAGE SDT request not received. (SNAERR 102)
CAUSE The host has not sent the necessary command sequence to
activate your session.
ACTION Check with your system administrator or IBM operator to
make sure the NAUs on the HP 3000 have been properly
activated, then try again.
---------------------------------------------------------------------------------------
SNAERR 103 MESSAGE Invalid session control protocol. (SNAERR 103)
CAUSE An internal error has occurred in the SNA Link subsystem,
or an illegal request was received from the host.
ACTION Note the circumstances and report them to your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 104 MESSAGE RQR request pending. (SNAERR 104)
CAUSE SNA IMF has requested recovery for the session.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 105 MESSAGE STSN request not pending. (SNAERR 105)
CAUSE There is no STSN pending.
ACTION Note the circumstances and contact your HP
representative.
Table A-0. (cont.)
---------------------------------------------------------------------------------------
SNAERR 106 MESSAGE Pacing not allowed. (SNAERR 106)
CAUSE An invalid attempt was made to use pacing.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 107 MESSAGE Unsupported CRV request/response. (SNAERR 107)
CAUSE The primary requested an unsupported function. SNA Link
does not support Cryptography Verification (CRV).
ACTION Change the host application's BIND to turn off
cryptography.
---------------------------------------------------------------------------------------
SNAERR 108 MESSAGE Unsupported session control request. (SNAERR 108)
CAUSE An unsupported session control request was attempted.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 109 MESSAGE Unsupported session control response. (SNAERR 109)
CAUSE An unsupported session control response was detected by
SNA Link.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 110 MESSAGE No such deact req (UNBIND,DACTLU,DACTPU) rcvd. (SNAERR
110)
CAUSE No deactivation request has been received.
ACTION Note the circumstances and contact your HP
representative.
---------------------------------------------------------------------------------------
SNAERR 111 MESSAGE No such act req (BIND,,ACTPU) rcvd. (SNAERR 111)
CAUSE No activation request has been received for your NAU.
ACTION Ensure that the NAU has been activated on the host.
---------------------------------------------------------------------------------------
SNAERR 112 MESSAGE CLEAR request not received. (SNAERR 112)
CAUSE The primary session control has not sent a CLEAR.
ACTION Note the circumstances and contact your HP
representative.