|
|
- WebWise Apache in FOS
-
- Support for Using the Entire Disk Space on LDEV 1
- MPE/iX 7.5 Software Maintenance Manual HTML Incorrectly Created
For MPE/iX 7.5, WebWise server has been updated to version A.03.00 and replaces
Apache in FOS as a no-extra-cost bundled product.
Migrating from Previous Versions of Apache
The /APACHE/PUB/JHTTPD job stream file from previous versions of
Apache is not compatible with HP WebWise MPE/iX Secure Web Server. You must
manually create a new JHTTPD job stream file by using the WebWise
/APACHE/PUB/JHTTPD.sample template.
The /APACHE/PUB/conf/httpd.conf configuration file from previous
versions of Apache may or may not be compatible with WebWise, depending on the
previous Apache version:
1.3.4 -- NOT compatible. You must use
/APACHE/PUB/conf/httpd.conf.sample as a template to create a
new httpd.conf file.
1.3.9 -- compatible, but SSL functionality will not be enabled.
To enable SSL functionality you MUST use
/APACHE/PUB/conf/httpd.conf.sample as a template to create
a new http.conf file.
1.3.14 -- compatible, but SSL functionality will not be enabled.
To enable SSL functionality you MUST use
/APACHE/PUB/conf/httpd.conf.sample as a template to create
a new http.conf file.
In addition to updating /APACHE/PUB/conf/httpd.conf, it is strongly
recommended to update all of the configuration files in the same directory by
using the corresponding *.sample files.
Migrating from WebWise A.01.00
HP WebWise MPE/iX Secure Web Server version A.03.00 was designed to be a
drop-in replacement for Apache, and does not attempt to upgrade or migrate any
files from the WebWise A.01.00 /APACHE/SECURE directory tree.
You must manually use the A.03.00 *.sample files in the
/APACHE/PUB/conf directory tree to create new standard configuration
files, and then propagate any local customization that you made in the A.01.00
/APACHE/SECURE/conf directory tree.
You will need to copy your server key and certificate from the old A.01.00
locations of /APACHE/SECURE/conf/ssl.key/server.key and
/APACHE/SECURE/conf/ssl.crt/server.crt to the new A.03.00 locations of
/APACHE/PUB/conf/ssl.key/server.key and
/APACHE/PUB/conf/ssl.crt.server.crt.
Any A.01.00 CGI applications in /APACHE/SECURE/cgi-bin or any data
content in /APACHE/SECURE/htdocs can either be moved to the
corresponding A.03.00 directories in /APACHE/PUB, or left in place
after adjusting the new A.03.00 configuration files to refer to the old
A.01.00 locations.
WebWise A.01.00 accessed web page content as the user SECURE.APACHE,
but WebWise A.03.00 accesses web page content as the user www.APACHE.
This is the same user as used by Apache A.02.00.
With this release, the MPE/iX operating system uses the full capacity of the
disk configured as LDEV 1. This feature works with all HP supported disks and
disk arrays regardless of the disk capacity. It is enabled for all the LDEV 1
disks with a disk capacity of more than 5 GB.
Before installing, you should be aware of the following considerations.
It is strongly recommended that a FULL system backup be taken before install.
 |
NOTE: DO NOT miss reading this. After the install, if backdating to a
pre-7.5 version is required at a later point, HP recommends that the user
perform an INSTALL from the pre-7.5 backup instead of backdating.
Alternatively, the user may perform a full backup, INSTALL a pre-7.5 version,
and then restore files from the backup.
|
Behavior of device specification by DEV=**$system_master or 1 in
FILE/BUILD commands needs to be understood. With
DEV=**$system_master specification, the files would be placed within
the first 4 GB of LDEV 1. If the device is specified as DEV=1, then the system
would attempt to store the files beyond 4GB disk space. If that fails, the
files would be placed within 4GB disk space. Note that system utilities (ISL>LS)
need to be stored within the first 4 GB of disk space and the install/update
process will take care of this.
For more information on the LDEV 1 >4GB enhancement, see "Support for Using the
Entire Disk Space on LDEV 1" in the Communicator for MPE/iX Release 7.5.
This document is available online at docs.hp.com.
CR# JAGae62324/8606298826
As the InstantInfo CD that came with the MPE/iX Release 7.5 has incorrect step
numbering in several sections of the HP e3000 MPE/iX System Software
Maintenance Manual, please reference only the online versions of this
document. The URLs for this manual are:
PDF format (preferred for use)
http://docs.hp.com/mpeix/pdf/30216-90344.pdf
HTML format
http://docs.hp.com/mpeix/onlinedocs/30216-90344/30216-90344.html
|