|
|
This section describes how to determine your system configuration group.
The factory System Load Tape (SLT) does not contain a default I/O configuration.
During an installation, you must specify the appropriate factory
configuration group when booting the system immediately after installing
the factory SLT. Listing the system configuration uses the off-line diagnostic
tool, Mapper. To get help using MAPPER, type help at
the MAPPER prompt, and see Figure 5-1
"Sample Listing MAPPER Output" for a sample listing.
To list the system configuration:
Check that all hardware peripherals are attached and powered on.
Start ODE.
ISL>ODE
Display hardware configuration.
ODE>RUN MAPPER
ODE>RUN MAPPER2 (for N-Class and A-Class systems)
The figure on the following page is a sample of a MAPPER
display.
Record the I/O configuration for your system.
Find the MPE/XL Model String. Then refer to
Appendix B "Configuration Tables" for the
configuration group name for your HP e3000 model in the SCSI column.
For example, for a Model 995, the SCSI group is CONFG995. It is very
important to have the exact group name. Check carefully for numbers
zero and 1 and letters O and I.
Exit mapper.
ODE>EXIT
Figure 5-1 Sample Listing MAPPER Output
STARTING EXECUTION OF MAPPER
Processor Identification: Hardware Model: 590H, Revision: 0
Software Model: 4H, Revision: 0
Hardware ID: 0, Software ID: 250911381 (unsigned decimal)
Software Cap: 0x10000031
MPE/XL Model String: 979-400
Processor Board Revisions:
CPU - CPU Chip: 769
PDC - Processor Dependent Code: 38.29
Cache and TLB Sizes:
Instruction Cache: 1024 K bytes, Instruction TLB: 96 entries
Data Cache: 1024 K bytes, Data TLB: 96 entries
Co-processors:
Floating Point Co-processor is installed
I/O Configuration:
Type HW SW Revisions
Path Component Name ID Mod Mod Hdwr Firm
--------- ---------------------------------- ----- ----- ----- ----- -----
8 I/O Adapter CH 580H BH 15 1
8/63 GSC+ Port 7H 501H CH 1 3
10 I/O Adapter CH 580H BH 15 1
10/4 Upper Bus Converter 7H 500H CH 0 0
10/4/0 HP-PB LAN/Console 2H 5H 60H 0 1
10/4/4 HP-PB Fast Wide SCSI 4H 4H 3BH 0 0
10/4/4.2.0 SEAGATE ST318275LC - - - - HP00
10/4/4.3.0 SEAGATE ST39175LC - - - - HP00
10/4/4.4.0 SEAGATE ST39175LC - - - - HP00
10/4/8 HP-PB SCSI 4H 4H 39H 0 0
10/4/8.0.0 SEAGATEST32550N disk drive - - - - HP10
10/4/8.1.0 SEAGATE ST34572WC - - - - HP01
10/4/8.2.0 SEAGATE ST32272WC - - - - HP01
10/4/9 HP-PB Centronics 5H 4H 3AH 0 0
10/4/20 HP-PB SCSI 4H 5H 39H 0 0
10/4/20.0.0 HPC1533A/C1530B tape drive - - - - AN04
10/4/20.1.0 HPC1533A/C1530B tape drive - - - - AN04
10/4/24 HP-PB Fast Wide SCSI 4H 5H 3BH 0 0
10/4/24.3.0 SEAGATE ST34371W disk drive - - - - HPM2
10/4/24.4.0 SEAGATE ST34371W disk drive - - - - HPM2
10/4/24.5.0 Quantum XP34361WD - - - - HP10
10/4/24.6.0 SEAGATE ST34371W disk drive - - - - HPM4
10/4/60 HP-PB Port 7H 103H CH 0 0
10/16 Upper Bus Converter 7H 500H CH 0 0
10/16/60 HP-PB Port 7H 103H CH 0 0
10/63 GSC+ Port 7H 501H CH 1 3
32 MoHawk Processor 0H 590H 4H 0 0
34 MoHawk Processor 0H 590H 4H 0 0
36 MoHawk Processor 0H 590H 4H 0 0
38 MoHawk Processor 0H 590H 4H 0 0
49 Memory (1024 M bytes) 1H 32H 9H 0 0
Extender 0
slot 0A/0B bank 3: 64MB
bank 8: 64MB
slot 1A/1B bank 7: 64MB
bank 12: 64MB
slot 2A/2B bank 4: 64MB
bank 15: 64MB
slot 3A/3B bank 0: 64MB
bank 11: 64MB
slot 4A/4B bank 5: 64MB
bank 14: 64MB
slot 5A/5B bank 1: 64MB
bank 10: 64MB
slot 6A/6B bank 2: 64MB
bank 9: 64MB
slot 7A/7B bank 6: 64MB
bank 13: 64MB
RUN COMPLETED.
|