 |
» |
|
|
|
The Neighbor Gateway Reachable Networks screen (#158) in Figure 8-9 “Neighbor Gateways Reachable Networks
Screen” is displayed when you
select a gateway name at the Neighbor Gateways screen (Figure 8-8 “Neighbor Gateways Screen”) and press the [Add]
or [Modify] function key. It is also displayed
when you type the path name: @NETXPORT.NI.NIname.INTERNET.gatewayn in the command window of any screen and press the [Enter]
key, where NIname is a configured token ring
NI, and gatewayn is the configured token ring
neighbor gateway name. Figure 8-9 Neighbor Gateways Reachable Networks
Screen
![[Neighbor Gateways Reachable Networks Screen]](img/gfx69.gif)
After you have entered all the required data, press the [Save Data]
function key to transfer the data displayed on the screen to the
configuration file you are creating or updating. Verify that the
data record has been created by checking that the Data flag is set
to Y. | | | |  | NOTE: The information configured in this screen can extend
to more than one page, if necessary, to allow configuration of up
to 2550 reachable networks per link (255 pages and 10 reachable
nets per page). Press [Next Page] to proceed to
a new page. Press [Prev Page] to display a prior
page. Use [First Page] to display the first page
(for example, if you are viewing the third page, pressing [First Page]
will immediately display the first page). Press [Last Page]
to display the last page of reachable networks that has been configured.
To consolidate reachable networks entries (from several pages, for
example) press [Condense Page]. | | | | |
Fields- Neighbor gateway IP internet address
Enter the full network address of a gateway node
(on this network) that is to be used to reach other networks (any
network in the same internetwork other than the network of which
this node is a member). The network portion of the address must
be the same as that entered on the IP Protocol Configuration screen
for the network interface you are configuring; however, the node
portion need not match. There are two methods of entering an internet protocol (IP)
address within NMMGR: Enter the fully qualified IP address
(for example, Class C, C 192.191.191 009) OR Enter only the network (nnn)
and node (xxx) portions of the IP address as
four positive integers between 0 and 255 separated by periods or
blanks (for example, 15.123.44.98). You need not enter the following items as NMMGR will fill
these in:- Class A, B, C - Leading zeros for the network and node portion
of the IP address.
Addresses are made up of a network
portion and a node portion. The supported
classes of network addresses have the following forms: - Class C:
C nnn.nnn.nnn xxx - Class B:
B nnn.nnn xxx.xxx - Class A:
A nnn xxx.xxx.xxx
where nnn is a value
ranging from 000 to 255, representing eight bits of the network
portion of an address and xxx is a value ranging
from 000 to 255, representing the node portion of the address. Note that network and node values of all zeros or all ones
are not allowed. These are special values. The leftmost group of nnn has the following
ranges for each address class: - Class C:
192-223 - Class B:
128-191 - Class A:
001-126
The network address (network portion of the IP address) configured
in NETXPORT.NI.NIname.PROTOCOL.IP
must match the neighbor gateway IP internet address configured in
the current screen. Default value: None
- Configured reachable networks IP network address
Enter the internet addresses of the remote networks
that can be reached through the gateway whose network address is
configured in the previous field. You can also designate this gateway as a default gateway by
entering an "at" sign (@)
in one of the Configured reachable networks IP network address
fields. The network will route messages to the default gateway if
it is unable to locate their destination by any other means. The
default gateway will then attempt to locate the destination. When specifying reachable networks, entering only the network
portions, and optionally the subnet, of the IP address (setting
the node portion to all zeros) allows this node to communicate with
any other node on the remote network. If the remote network is subnetted, you can restrict communication
of this node to particular subnets by entering the decimal equivalent
of those subnets and including the IP mask in the IP mask field. To allow this node to communicate with other subnets on the
local network, enter the decimal equivalent of the subnet in the
IP network address field and enter the subnet mask in the IP mask
field. If you do not enter a subnet mask, one of the following occurs: If the IP address is different from the node you
are configuring, NMMGR assumes no subnets. Related screen: NETXPORT.NI.NIname.INTERNET This path name corresponds to the Neighbor Gateways screen.
A Neighbor Gateway Reachable Networks screen must be configured
for each gateway configured in the Neighbor Gateways screen.
|
