 |
» |
|
|
|
Refer to Chapter 3 “System Startup Functions” for information on the steps involved in the startup
process. The following listing shows the Series 950 ISL START
(autoboot on) sequence received at
the console. Sequences from other installations may vary:
CM> TC
Processor Dependent Code (PDC) revision 2.8
Console path = 2/4.1.0.0.0.0.0
Primary boot path = 2/4.0.0.0.0.0.0
Alternate boot path = 6/4.3.0.0.0.0.0
32 MB of memory configured and tested.
Soft Booted- -memory state is valid
Autoboot from primary path enabled.
To override, press any key within 10 seconds.
10 seconds expired--proceeding with autoboot
console IO Dependent Code (IODC) revision 3
Boot IO Dependent Code (IODC) revision 3
Booted.
MMSAVE Version 9.90
DUMPAREA protected, proceeding to ISL without memsave
ISL loaded
ISL Revision 2738 September, 1987
Cannot find an auto-execute file. AUTOBOOT ABORTED.
ISL> START
MPE/XL launch facility
Initialize_genesis - Version : <<870204.1552>>
THU, MAY 26, 1988, 4:28:32 PM (y/n)?
[TMUX_DAM] 15 7 12 14
Initialize genesis completed.
Create Console Messages kso completed.
Initialize memory manager completed.
Initialize resident kernel completed.
beginning recovery
setup complete - beginning recovery of free space map and label table
completed recovery of free space map and label table
completed recovery of files
begin posting of recovered files
recovery completed
NEW and TEMP files deallocated for MPEXL_SYSTEM_VOLUME_SET:MEMBER1
(LDEV 1)
Initialize volume management completed.
Opening the native system library completed.
Initialize process management completed.
Initialize debug subsystem completed.
Initialize file system completed.
Initialize loader completed.
Initialize non-resident services completed.
Begin binding compatibility mode SL
Compatibility mode SL binding complete
Create port process has been completed.
Warning - Protection of the system file `AUTOBOOT.MPEXL.SYS',
failed.
Protection of system files has been completed.
The following is a list of the boot options -
last boot command: INSTALL last configuration group: CONFIG
current boot command: START current configuration group: CONFIG
logon = OPERATOR.SYS
NORECOVERY MULTI-USER
MULTI-DISK SYSSTART
Entering - System I/O configuration.
The path 2 has already been configured.
The path 2/4 has already been configured.
The path 2/4.0 has already been configured.
The path 2/4.0.0 has already been configured.
The path 2/4.0.2 was configured but is not available.
The path 2/4.1 has already been configured.
The path 2/4.1.0 has already been configured.
The path 2/4.3.0 was configured but is not available.
The path 2/4.3.4 was configured but is not available.
The path 2/4.3.5 was configured but is not available.
The path 2/8.0.0 was configured but is not available.
The path 2/8.0.1 was configured but is not available.
The path 2/8.0.2 was configured but is not available.
The path 2/8.0.3 was configured but is not available.
The path 2/8.1.0 was configured but is not available.
The path 2/8.1.1 was configured but is not available.
The path 2/8.1.2 was configured but is not available.
The path 2/8.1.3 was configured but is not available.
The path 6/4.0.0 was configured but is not available.
The path 6/4.0.1 was configured but is not available.
The path 6/4.0.2 was configured but is not available.
The path 6/4.3.4 was configured but is not available.
The path 6/4.3.5 was configured but is not available.
The path 6/4.3.7 was configured but is not available.
Leaving - System I/O configuration.
SYSTEM I/O AT BOOT TIME
ldev: 1 HP7937H configured available 2/4.0.0
ldev: 2 HP7937H configured available 2/4.0.1
ldev: 3 HP7933H configured not-available 2/4.0.2
ldev: 6 HP2567A configured available 6/4.3.6
ldev: 7 HP7980A configured available 6/4.3.0
ldev: 8 HP7978B configured not-available 2/4.3.0
ldev: 10 HP7980A configured not-available 6/4.3.7
ldev: 19 HP2680A configured not-available 6/4.3.4
ldev: 20 HP2392A configured available 2/4.1.0
ldev: 21 HP7937H configured not-available 6/4.0.0
ldev: 22 HP7937H configured not-available 6/4.0.1
ldev: 23 HP7937H configured not-available 6/4.0.2
ldev: 25 HP7937H configured not-available 2/8.0.0
ldev: 26 HP7937H configured not-available 2/8.0.1
ldev: 27 HP7933H configured not-available 2/8.0.2
ldev: 28 HP7933H configured not-available 2/8.0.3
ldev: 29 HP2688A configured not-available 6/4.3.5
ldev: 30 HP2688A configured not-available 2/4.3.4
ldev: 31 HP7937H configured not-available 2/8.1.0
ldev: 32 HP7937H configured not-available 2/8.1.1
ldev: 33 HP7935H configured not-available 2/8.1.2
ldev: 34 HP7935H configured not-available 2/8.1.3
ldev: 39 HP2688A configured not-available 2/4.3.5
MEMORY AVAILABLE FOR USE (bytes) : 33554432
Entering - Initialize system member volumes
Leaving - Initialize system member volumes
Entering - Mount all volumes
VOLUME ALREADY MOUNTED ON LDEV 1 (AVR 10)
A volume has been mounted on ldev 1
LONER VOLUME MOUNTED ON LDEV 2 (AVR 11)
A volume has been mounted on ldev 2
Warning - Volume is not available for mounting. The ldev is 3
Warning - Volume is not available for mounting. The ldev is 25
Warning - Volume is not available for mounting. The ldev is 26
Warning - Volume is not available for mounting. The ldev is 27
Warning - Volume is not available for mounting. The ldev is 28
Warning - Volume is not available for mounting. The ldev is 31
Warning - Volume is not available for mounting. The ldev is 32
Warning - Volume is not available for mounting. The ldev is 33
Warning - Volume is not available for mounting. The ldev is 34
Warning - Volume is not available for mounting. The ldev is 21
Warning - Volume is not available for mounting. The ldev is 22
Warning - Volume is not available for mounting. The ldev is 23
Leaving - Mount all volumes
The current boot command has been saved on the system master.
NMLG FILE NUMBER 0 ON.
[PSI_DUMP_SURR] Version A.00.01.026
16:30/11/DCC STARTUP - ENTER - version C0005105 compiled 880322
16:30/11/DCC warning 128-1, (Startup) can not open NMCONFIG,
status FF09008F.
16:30/18/DCC ERROR 14-1, Configuration file open error 001000B4.
16:30/11/DCC STARTUP - ERROR
System State: Initializing Mode.
Reply Information Table has been initialized!
System State: Multiuser Mode.
SYSTEM LOG FILE #1 IS ON
Initializing Job & Session
Initiate Operator Log On
SESSION Scheduling Initialized
JOB Scheduling Initialized
Successfully launched diagnostic monitor process.
ACCT EXISTS, USER NAME DOESN'T. (CIERR 1438)
16:31/24/MISSING USER NAME DURING LOGON ON LDEV #20. (js 11)
MPE XL:
|
|
