 |
» |
|
|
|
Planning can and should be done prior to performing your backdate.
The backdate requires downtime and planning it ensures that all
the requirements are met. The sections include: Determine Your Backdate Method Validate Your System Backup (Method 1)
Determine Your Backdate Method |  |
There are essentially three methods for backdating your system
software version level. The methods are as follows: Method 1: Using a Customized System
Load Tape. See CSLT;CSLT:backdating>Customized System Load Tape
(CSLT) together with the Fundamental Operating System (FOS) and
Purchasable Products (SUBSYS) tapes from the earlier release. The CSLT you use to backdate your system could have been created
under many different circumstance. For example: During a system update (with no patches) While installing patches from a PowerPatch tape While updating and installing patches from a PowerPatch
tape
Method 2: Using Factory System Load Tape (SLT) and
Fundamental Operating System (FOS) and Purchasable Products (SUBSYS)
tapes from the earlier release. Method 3: Using a Factory Preload Tape (FPT). If
your system was preinstalled at the factory, you must backdate using
the FPT.
The system software version level options are: Backdate from 6.0 to 5.0 (General Release)
 |  |  |  |  | NOTE: Backdating from 6.0 to a release before 5.0 (General
Release) is not supported. |  |  |  |  |
To determine which method is optimal for your system and your
situation, call the Response Center, if you have a software support
contract, or your HP representative, before deciding to backdate
your system. If your Hewlett-Packard representative and you both agree
that backdating your operating system is necessary, follow the steps
below. Please read all the instructions in this chapter before you
begin your backdate. Determine what prior IO devices you will back
date to. Verify Your Requirements |  |
To verify your requirements for backdating: Review and confirm the process you
are going to perform with the HP Response Center or your representative.
Table D-1 Required
Backdating Materials Requirement | Method 1 | Method 2 | Method 3 |
---|
CSLT (for the
release to which you want to backdate) from the system you want
to backdate. | Required | | | HP-provided
factory SLT (for the release to which you want to backdate). | | Required | | HP-provided
factory preload tape (FPT) that came with the system. | | | Required | Fundamental
Operating Software (FOS) tape from the release to which you want
to backdate. | Required | Required | | SUBSYS tape
from the release to which you want to backdate, if you installed
or updated any optional products with that release. | Required | Required | Required | A STORE
tape with HPSWINFO.PUB.SYS, NMCONFIG.PUB.SYS,
and NMINIT.PUB.SYS from the release
to which you want to backdate. | Required | Required | Required | A STORE
tape with @.CONFIG.SYS from the
release to which you want to backdate. If this is not available,
run SYSGEN and customized the factory
supplied configuration file for your system. | Recommended | | Recommended | Current full
system backup tapes. | Required | Required | Required | Patch tapes (to reapply
patches) if you had installed patches onto the earlier release of
the system. | | Required | Required |
Compatibility Issues |  |
While backdating, you may encounter compatibility issues that
arise from backdating certain purchasable products. Before you proceed,
we recommend that you read: The Communicator 3000
for the release you are backdating to, as well as the copy you received
with your new release. These documents provide additional information
on backdating specific products. Check that any new disk drive in the configuration
is supported on the release you are backdating to.
Patch Considerations |  |
If you have applied patches to your level 5.0 or 5.5 system
software, read the section appropriate to the backdating method
you are using. The sections are: Method 2: Using a Factory SLT
The CSLT you use to backdate your system could have been created
under many different circumstances. For example: During a system update (with no patches) While installing patches from a PowerPatch tape
If you installed patches from a PowerPatch tape on your system,
you need to restore the STORE files that are appended to the CSLT
created during the installation of the most recent PowerPatch tape.
Refer to "Restore FOS and SUBSYS" for directions
on restoring the STORE portion
of the CSLT. If you applied other patches to your system (such as reactive
patches), you need to reapply them at the end of the process. If you are not sure what patches have been applied to your
system, be sure to call the Response Center or HP Representative
before backdating your system. Method 2: Using a Factory SLTIf any patches were applied to your 5.0 or 5.5 system, they
must be reapplied from the PowerPatch tape(s) after the backdate.
Follow the appropriate manual for the release you are backdating
to. To determine the patches that were applied to your system,
restore the HPSWINFO file from
a backup of the release you are backdating
to. If any patches were applied to your 5.0 or 5.5 system, they
must be reapplied from the PowerPatch tape(s) after the backdate.
Follow the appropriate manual for the release you are backdating
to. Check Patch Tape Media |  |
To verify the patch tape source media and contents: Log on from the
console with the following conditions. :HELLO MANAGER.SYS,INSTALL;HIPRI :OPENQ LP :STREAMS streams_device
|
An LP device must be configured in SYSGEN.
A common streams_device
value is 10. Already spooled and streamed messages might display. Collect the tape media you will be using as source
material to modify the system software. This includes the PowerPatch
and Reactive Patch tapes. If you have a PowerPatch tape, check it to ensure
the tape is not damaged. If you do not have a PowerPatch tape, proceed to Step 4. Mount PowerPatch
tape. :FILE TAPE;DEV=TAPE :VSTORE *TAPE;@.INSTALL.SYS;SHOW
|
Reply to the tape request. vstore displays a listing
of verified files. These files are not being
restored to disk.
If you have a Reactive patch tape, check it to ensure
that it is not damaged. If you do not have a Reactive patch tape, proceed to Step
5. Mount Reactive
tape. :FILE TAPE;DEV=TAPE :VSTORE *TAPE;@.@.@;SHOW
|
Reply to the tape request. vstore displays a listing
of verified files. These files are not being
restored to disk.
If any files are not verified or if you receive
any errors or warnings, ensure your tape drive is clean and repeat
the procedure to be sure it is a media problem and not a dirty tape
drive. Run the cleaning cartridge through your DDS drive at least
three times to ensure that the drive is thoroughly cleaned. If your media is bad, contact your local HP Support Representative.
Validate Your System Backup (Method 1) |  |
If you are using a CSLT (Method 1) to backdate your system,
perform the steps in this section. If you are using a Factory SLT (Method 2) or a Factory Preload
Tape (Method 3), proceed to "Check for Disk Space." Before you begin the process of backdating, log on and verify
that your backup tape is valid. From the console,
log on with the following conditions. :HELLO MANAGER.SYS,INSTALL;HIPRI :SPOOLER LP;OPENQ :STREAMS streams_device
|
where streams_device
is the device number. A common streams_device
value is 10. An LP device must be configured in SYSGEN.
Already spooled and streamed messages might display. Validate the backup created before you started the
update process that you are now backdating from. You need the valid
backup to restore the NMCONFIG
file. Use the VSTORE command to
make sure that the full backup is readable. :FILE TAPE;DEV=tape_device :VSTORE *TAPE;@.@.@;SHOW=OFFLINE;DIRECTORY
|
If your backup is not valid, you must use Method 2 or Method
3.
Check for Disk Space |  |
Ensure you have sufficient disk space to backdate your system. Refer to "Estimating Disk Space" in Chapter 3 “Planning for Your Task” and Appendix C “Managing Disk Space” for additional
information about these steps. Reserve contiguous
and non-contiguous disk space. :BUILD AXLDEV1;DISC=n,1,1;DEV=1 :BUILD AXLSPACE;DISC=m,32,32
|
where: - n
AXLDEV1 number,
determined in Chapter 3 “Planning for Your Task”
or use the default of 120,000 sectors. - m
AXLSPACE number,
use the maximum value 1,084,000 (for 5.0 or 5.5 versions)
If a colon (:) prompt is returned. The files were built and
you have enough disk space. If you receive a message: Out of disk space,
you need to make more space. Purge the AXLSPACE
file. The AXLDEV1 file is automatically
purged by the UPDATE tool. If you do not have enough disk space, either contiguous
(AXLDEV) or non-contiguous (AXLSPACE): Store files to tape. Purge the stored
files from the system. Purge the files and groups as directed in Steps
8 through 10 of the next section, "Securing Your System."
|