HP 3000 Manuals HP 3000 Manuals
UPS (contd.)
549 MESSAGE UPS Monitor logic error: During shutdown
processing, while aborting UPS I/O requests, the
UPS Monitor detected an "invalid number of UPS's
configured" condition in its global table. (UPSERR
0549)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
550 MESSAGE UPS Monitor logic error: During shutdown
processing, while aborting UPS I/O requests, the
UPS Monitor detected an "invalid number of UPS's
monitored" condition in its global table. (UPSERR
0550)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
551 MESSAGE UPS Monitor logic error: During shutdown
processing, while aborting UPS I/O requests, the
UPS Monitor detected a Nil UPS Table Pointer
condition in its global table. (UPSERR 0551)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
552 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
Abortio_Request. (UPSERR 0552)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
553 MESSAGE UPS Monitor logic error: During shutdown
processing, while aborting UPS I/O requests, the
UPS Monitor detected an invalid UPS Table Entry.
(UPSERR 0553)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
554 MESSAGE UPS Monitor logic error: During shutdown
processing, while aborting UPS I/O requests, the
UPS Monitor detected an invalid count of UPS I/O
requests outstanding. (UPSERR 0554)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
555 MESSAGE UPS Monitor logic error: During shutdown
processing, the UPS Monitor found that the UPS
Monitor operating state was invalid when the
shutdown event message was received. (UPSERR 0555)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
556 MESSAGE UPS Monitor logic error: During shutdown
processing, the UPS Monitor found that a shutdown
operation was already in progress. (UPSERR 0556)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
557 MESSAGE UPS Monitor logic error: During shutdown
processing, when attempting to start the shutdown
limit timer, the UPS Monitor found that a shutdown
limit timer was already running. (UPSERR 0557)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
558 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
Release_Timer. (UPSERR 0558)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
559 MESSAGE UPS Monitor logic error: During UPS I/O
completion processing in the "Set Terminal
Controls" sequence, an I/O reply message was
received that was not of the expected (Terminal
Control) type. (UPSERR 0559)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
560 MESSAGE UPS Monitor logic error: While processing an I/O
Write completion, an I/O reply message was received
that was not of the expected (Write) type. (UPSERR
0560)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
561 MESSAGE UPS Monitor logic error: While processing an I/O
Read completion, an I/O reply message was received
that was not of the expected (Read) type. (UPSERR
0561)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
562 MESSAGE UPS LDEV ! I/O Operation error: The actual Write
data transfer length in a UPS Write I/O operation
was not the expected (requested) transfer length.
(UPSERR 0562)
CAUSE This is a software-detected error condition that
indicates an error in the I/O software subsystems
that the UPS Monitor uses to communicate with UPS
devices.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
563 MESSAGE UPS LDEV ! I/O Operation error: The actual Read
data transfer length in a UPS Read I/O operation
was too short, less than the minimum required Read
transfer length. (UPSERR 0563)
CAUSE This is a software-detected error condition that
indicates an error in the I/O software subsystems
that the UPS Monitor uses to communicate with UPS
devices. It could also indicate an I/O interface
hardware error, or a UPS hardware error
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
564 MESSAGE UPS LDEV ! I/O Operation error: The actual Read
data transfer length in a UPS Read I/O operation
was too long, greater than the maxmimum requested
Read transfer length. (UPSERR 0564)
CAUSE This is a software-detected error condition that
indicates an error in the I/O software subsystems
that the UPS Monitor uses to communicate with UPS
devices. It could also indicate an I/O interface
error or a UPS hardware error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
565 MESSAGE UPS Monitor logic error: UPS Monitor found global
timer_id of zero, which is invalid, when it
attempted to release the shutdown limit timer.
(UPSERR 0565)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
566 MESSAGE UPS Monitor logic error: UPS Monitor detected
invalid parameters in a call to one of its
procedures that inspects UPS Read data for matching
to expected UPS input data patterns. (UPSERR 0566)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
567 MESSAGE UPS LDEV ! I/O operation error: Data supplied by
the UPS device in response to a Read I/O request
did not match any of the allowable data patterns
for that request. The Read will be re-done. (UPSERR
0567)
CAUSE Possibly a poor I/O interface cable connection
between the system and the UPS. Possibly electrical
noise interference induced in the I/O interface
cable or hardware. It could also indicate a
malfunction of the UPS hardware.
ACTION If this error appears only rarely, then no action
is needed. If it appears frequently, then call
your Hewlett-Packard service representative.
---------------------------------------------------------------
568 MESSAGE UPS Monitor logic error: Table lookup of what
should have been a valid UPS power status character
failed to find the character in the lookup table.
(UPSERR 0568)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
569 MESSAGE UPS Monitor logic error: Table lookup of what
should have been a valid UPS alarm status character
failed to find the character in the lookup table.
(UPSERR 0569)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
570 MESSAGE UPS Monitor logic error: Table lookup of a UPS
status character produced inconsistent results: The
lookup procedure declared that it had found the
character, but reported its type as "unknown".
(UPSERR 570)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
571 MESSAGE UPS Monitor logic error: After deciding that a
UPS status character was valid, the UPS Monitor
then failed to find that status character in its
status lookup table. (UPSERR 0571)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
572 MESSAGE UPS LDEV ! I/O operation error: The I/O
completion status reported for the UPS I/O
operation had an incorrect, unexpected I/O
subsystem number in it. (UPSERR 0572)
CAUSE This is a software-detected error condition that
indicates an error in the I/O software subsystems
that the UPS Monitor uses to communicate with UPS
devices.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
573 MESSAGE UPS LDEV ! initialization error: After trying
several times, the UPS Monitor has been unable to
complete the initialization sequence of I/O
operations for this UPS device. (UPSERR 0573)
CAUSE Something is preventing the HP3000 system from
communicating with the UPS. Possibly a bad I/O
interface cable or bad I/O interface hardware at
the system or at the UPS. Possibly a UPS hardware
malfunction.
ACTION Check the I/O interface cable for correct
attachment, and check that the UPS is powered-on.
Check that the system I/O configuration is correct.
If the prob- lem is not found, then call your
Hewlett-Packard service representative.
---------------------------------------------------------------
574 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
Simple_Create_Process. (UPSERR 0574)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
575 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
Find_Plabel_Info. (UPSERR 0575)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative
---------------------------------------------------------------
576 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
HPgetsysplabel. (UPSERR 0576)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
577 MESSAGE UPS Monitor warning: Too many UPS devices have
been configured in the system I/O configuration
files. The UPS Monitor can not monitor all of them;
it will monitor as many as it can. (UPSWRN 0577)
CAUSE Incorrect system I/O configuration. The system I/O
configuration, generated by SYSGEN and NMMGR
configurators, contains more than 128 UPS devices,
which is the maximum number that the UPS monitor
can handle simultaneously.
ACTION Review and correct the system I/O configuration,
reducing the number of UPS devices specified in the
configuration to an acceptable number.
---------------------------------------------------------------
578 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
Start_Shut_NM. (UPSERR 0578)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
579 MESSAGE UPS Monitor logic error: UPS Monitor attempted to
create a "zero size" UPS Table. (UPSERR 0579)
CAUSE This is a software-detected error condition that
indicates an error in the UPS Monitor software or
in some other system software, or a system memory
error.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
580 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
HPFOPEN. (UPSERR 0580)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------
581 MESSAGE UPS Monitor system call error: Error status !
(Subsystem # !, Error # !) received from procedure
FCLOSE. (UPSERR 0581)
CAUSE This is a software-detected error condition that
indicates an error occurred in a call to the
specified MPE/iX Operating System procedure when
that procedure was called by the UPS Monitor
software.
ACTION Call your Hewlett-Packard service representative.
---------------------------------------------------------------