HP 3000 Manuals HP 3000 Manuals
(S/R) (contd)
386 MESSAGE EXPECTED 'volumesetname' AFTER 'VOLSET=' WHERE
volumesetname IS THE NAME OF A VOLUME SET THAT IS
CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX
'VOLSET=volumesetname' (S/R 386)
CAUSE You did not type the volset parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
387 MESSAGE 'VOLSET' OPTION CANNOT BE USED WITH THE 'LISTDIR'
OPTION. (S/R 387)
CAUSE Volset and listdir options are not allowed on the
same command line.
ACTION Delete either volset or listdir option and retype
the command.
---------------------------------------------------------------
391 MESSAGE 'VOLCLASS' OPTION CANNOT BE USED WITH THE 'VOL'
OPTION. (S/R 391)
CAUSE Volclass and vol options are not allowed on the
same command line.
ACTION Delete either volclass or vol option and retype the
command.
---------------------------------------------------------------
392 MESSAGE 'VOLCLASS' OPTION CANNOT BE USED WITH THE 'DEV'
OPTION. (S/R 392)
CAUSE Volclass and dev options are not allowed on the
same command line.
ACTION Delete either volclass or dev option and retype the
command.
---------------------------------------------------------------
393 MESSAGE 'VOLCLASS' OPTION HAS BEEN REDUNDANTLY SPECIFIED.
(S/R 393)
CAUSE The VOLCLASS option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
394 MESSAGE EXPECTED '=volumeclassname' AFTER 'VOLCLASS'
OPTION. SYNTAX
'VOLCLASS=volumeclassname' (S/R 394)
CAUSE You did not type the volclass parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
395 MESSAGE INVALID VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS'
OPTION. VOLUMECLASS NAME MUST START WITH AN ALPHA
"A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR
"_". SYNTAX
'VOLCLASS=volumeclassname'. (S/R 395)
CAUSE Volumeclass name mispelled or not recognized on the
system.
ACTION Enter a system recognized volumeclass name.
---------------------------------------------------------------
396 MESSAGE VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS' OPTION
EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16
CHARACTERS. SYNTAX
'VOLCLASS=volumeclassname' (S/R 396)
CAUSE You entered a volumeclass name that was more than
16 characters.
ACTION Enter a volumeclass name that has 16 characters or
less.
---------------------------------------------------------------
397 MESSAGE EXPECTED 'volumeclassname' AFTER 'VOLCLASS='
WHERE volumeclassname IS THE NAME OF A VOLUME
CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON
YOUR SYSTEM. SYNTAX
'VOLCLASS=volumeclassname' (S/R 397)
CAUSE You did not specify a volumeclass name.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
398 MESSAGE 'VOLCLASS' OPTION CANNOT BE USED WITH THE
'LISTDIR' OPTION. (S/R 398)
CAUSE Volclass and listdir options are not allowed on the
same command line.
ACTION Delete either volclass or listdir option and retype
the command.
---------------------------------------------------------------
401 MESSAGE 'VOL' OPTION CANNOT BE USED WITH THE 'VOLCLASS'
OPTION (S/R 401)
CAUSE Vol and volclass options are not allowed on the
same command line.
ACTION Delete either vol or volclass option and retype the
command.
---------------------------------------------------------------
402 MESSAGE 'VOL' OPTION CANNOT BE USED WITH THE 'DEV' OPTION
(S/R 402)
CAUSE Vol and dev options are not allowed on the same
command line.
ACTION Delete either vol or dev option and retype the
command.
---------------------------------------------------------------
403 MESSAGE 'VOL' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R
403)
CAUSE The VOL option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
404 MESSAGE EXPECTED '=volumename' AFTER 'VOL' OPTION. SYNTAX
'VOL=volumename' (S/R 404)
CAUSE You did not type vol parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
405 MESSAGE INVALID VOLUME NAME SPECIFIED FOR 'VOL' OPTION.
VOLUME NAME MUST START WITH AN ALPHA "A-Z" AND
CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_".
SYNTAX
'VOL=volumename' (S/R 405)
CAUSE Volume name misspelled or unrecognizable volume
name was entered.
ACTION Enter the correct volume name.
---------------------------------------------------------------
406 MESSAGE VOLUME NAME SPECIFIED FOR 'VOL' OPTION EXCEEDED
THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS.
SYNTAX
'VOL=volumename' (S/R 406)
CAUSE The volume name you specified is too long. The
maximum number of chharacters is 16.
ACTION Specify a volume name with 16 or fewer characters.
---------------------------------------------------------------
407 MESSAGE EXPECTED 'volumename' AFTER 'VOL=' WHERE
volumename IS THE NAME OF A VOLUME (DISC) THAT IS
CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX
'VOLSET=volumesetname' (S/R 407)
CAUSE You did not enter the volumename.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
408 MESSAGE 'VOL' OPTION CANNOT BE USED WITH THE 'LISTDIR'
OPTION (S/R 408)
CAUSE Vol and listdir options are not allowed on the same
command line.
ACTION Delete either vol or listdir option and retype the
command.
---------------------------------------------------------------
411 MESSAGE WARNING: 'HIGH' OPTION HAS BEEN REDUNDANTLY
SPECIFIED (S/R 411)
CAUSE The HIGH option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
412 MESSAGE EXPECTED '={datasetnumber}' AFTER 'HIGH' OPTION.
SYNTAX
'HIGH={datasetnumber}' (S/R 412)
CAUSE You did not specify datasetnumber.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
413 MESSAGE EXPECTED 'HIGH={datasetnumber}' WHERE
{datasetnumber} IS A POSITIVE INTEGER DENOTING A
DATA SET BETWEEN 0 AND 199. SYNTAX
'HIGH={datasetnumber}' (S/R 413)
CAUSE You did not type the high parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
414 MESSAGE EXPECTED {datasetnumber} BETWEEN 0 AND 199.
SYNTAX
'HIGH={datasetnumber}' (S/R 414)
CAUSE You did not specify a number within the range.
ACTION Specify a number between 1 and 199.
---------------------------------------------------------------
415 MESSAGE {datasetnumber} SPECIFIED FOR 'HIGH' OPTION MUST
BE GREATER THAN OR EQUAL TO THE VALUE SPECIFIED FOR
THE 'LOW' OPTION. SYNTAX
'HIGH={datasetnumber}' (S/R 415)
CAUSE The high parameter is too small.
ACTION Specify a larger number for the high parameter.
---------------------------------------------------------------
421 MESSAGE WARNING: 'LOW' OPTION HAS BEEN REDUNDANTLY
SPECIFIED (S/R 421)
CAUSE The LOW option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
422 MESSAGE EXPECTED '={datasetnumber}' AFTER 'LOW' OPTION.
SYNTAX
'LOW={datasetnumber}' (S/R 422)
CAUSE You did not specify datasetnumber.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
423 MESSAGE EXPECTED 'LOW={datasetnumber}' WHERE
{datasetnumber} IS A POSITIVE INTEGER DENOTING A
DATA SET BETWEEN 0 AND 199. SYNTAX
'LOW={datasetnumber}' (S/R 423)
CAUSE You did not specify a number within the range.
ACTION Specify a number between 1 and 199.
---------------------------------------------------------------
424 MESSAGE {datasetnumber} SPECIFIED FOR 'LOW' OPTION MUST
BE LESS THAN OR EQUAL TO THE VALUE SPECIFIED FOR
THE 'HIGH' OPTION. SYNTAX
'LOW={datasetnumber}' (S/R 424)
CAUSE The low parameter is too large.
ACTION Specify a smaller number for low parameter.
---------------------------------------------------------------
425 MESSAGE EXPECTED {datasetnumber} BETWEEN 0 AND 199.
SYNTAX
'LOW={datasetnumber}' (S/R 425)
CAUSE You did not specify a number within the range.
ACTION Specify a number between 1 and 199.
---------------------------------------------------------------
431 MESSAGE 'FCRANGE' OPTION CANNOT BE USED WITH 'TRANSPORT'
to MPEv (S/R 431)
CAUSE Fcrange and transport options are not allowed on
the same command line.
ACTION Delete either fcrange or transport option and
retype the command.
---------------------------------------------------------------
432 MESSAGE WARNING: 'FCRANGE' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 432)
CAUSE The FCRANGE option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
433 MESSAGE EXPECTED '=filecode/filecode[,filecode/filecode...]'
AFTER 'FCRANGE' OPTION. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 433)
CAUSE You typed the fcrange parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
434 MESSAGE EXPECTED filecode IN FIRST PART OF
filecode/filecode OF 'FCRANGE' OPTION TO BE AN
INTEGER BETWEEN -32768 AND 32767. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 434)
CAUSE You typed the fcrange parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
435 MESSAGE SPECIFIED filecode OF 'FCRANGE' OPTION MUST BE AN
INTEGER BETWEEN -32768 AND 32767. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 435)
CAUSE You did not enter a valid file code range.
ACTION Enter a valid file code range.
---------------------------------------------------------------
436 MESSAGE EXPECTED A "/" TO SEPARATE filecode RANGES FOR
THE 'FCRANGE' OPTION. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 436)
CAUSE You typed the fcrange parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
437 MESSAGE EXPECTED filecode IN SECOND HALF OF
filecode/filecode OF 'FCRANGE OPTION TO BE AN
INTEGER BETWEEN -32768 AND 32767. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 437)
CAUSE You typed the fcrange parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
438 MESSAGE SECOND filecode OF A filecode/filecode PAIR IN
THE 'FCRANGE' OPTION MUST BE GREATER THAN THE
FIRST, Ex. 'FCRANGE=1030/1061'. SYNTAX
'FCRANGE=filecode/filecode[,filecode/filecode...]'
(S/R 438)
CAUSE The second file code that you specified was lower
than the first.
ACTION Retype the command so that the second file code is
higher than the first.
---------------------------------------------------------------
439 MESSAGE MAXIMUM NUMBER OF filecode RANGES (8) EXCEEDED
FOR THE FCRANGE OPTION (S/R 439)
CAUSE You specified too many file code ranges. The
maximum number is 8.
ACTION Specify 8 or fewer file code ranges.
---------------------------------------------------------------
440 MESSAGE 'FCRANGE' OPTION CANNOT BE USED WITH THE
'LISTDIR' OPTION (S/R 440)
CAUSE Fcrange and listdir options are not allowed on the
same command line. .
ACTION Delete either fcrange or listdir option and retype
the command.
---------------------------------------------------------------
441 MESSAGE WARNING: 'ONERROR' OPTION HAS BEEN REDUNDANTLY
SPECIFIED (S/R 441)
CAUSE The ONERROR option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
442 MESSAGE EXPECTED '={error-parm}' AFTER 'ONERROR' OPTION
WHERE error-parm IS ONE OF 'QUIT' OR 'SKIP'. SYNTAX
'ONERR[OR]={QUIT} OR {SKIP}' (S/R 442)
CAUSE You typed the onerror parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
443 MESSAGE THE 'FULL' PARAMETER OF THE 'ONERROR' OPTION
REQUIRES (PM) CAPABILITY (S/R 443)
CAUSE You do not have PM capability.
ACTION Log on to an account with PM capability.
---------------------------------------------------------------
444 MESSAGE UNKNOWN PARAMETER SPECIFIED FOR THE 'ONERROR'
OPTION. EXPECTED ONE OF 'QUIT' OR 'SKIP'. SYNTAX
'ONERR[OR]={QUIT} OR {SKIP}' (S/R 444)
CAUSE You did not specify a valid onerror option.
ACTION Retype the command and specify a valid onerror
option.
---------------------------------------------------------------
445 MESSAGE EXPECTED recovery type FOR THE 'ONERROR' OPTION.
EXPECTED ONE OF 'QUIT' OR 'SKIPFULL'. SYNTAX
'ONERR[OR]={QUIT} OR {SKIP}' (S/R 445)''
CAUSE You typed the onerror parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
446 MESSAGE 'ONERROR' OPTION CANNOT BE USED WITH THE
'LISTDIR' OPTION (S/R 446)
CAUSE Onerror and listdir options are not allowed on the
same command line.
ACTION Delete either onerror or listdir option and retype
the command.
---------------------------------------------------------------
447 MESSAGE 'ONERROR=FULL' FUNCTION NOT IMPLEMENTED (S/R
447)
CAUSE Onerror=full will be supported in the future
release.
ACTION Information only.
---------------------------------------------------------------
451 MESSAGE WARNING: 'SHOW' OPTION HAS BEEN REDUNDANTLY
SPECIFIED (S/R 451)
CAUSE The SHOW option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
452 MESSAGE EXPECTED '=showparm[,showparm..]' AFTER 'SHOW'
OPTION WHERE showparm IS ONE OF 'SHORT', 'LONG',
'DATES', 'OFFLINE', OR 'SECURITY'. SYNTAX
'SHOW=showparm[,showparm....]' (S/R 452)
CAUSE You typed the show parameter incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
453 MESSAGE 'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW'
OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED (LONG)
WILL BE USED (S/R 453)
CAUSE Show=long will be used.
ACTION Information only.
---------------------------------------------------------------
454 MESSAGE 'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW'
OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED
(SHORT) WILL BE USED (S/R 454)
CAUSE Show=short will be used.
ACTION Information only.
---------------------------------------------------------------
455 MESSAGE UNKNOWN PARAMETER SPECIFIED FOR THE 'SHOW'
OPTION. EXPECTED ONE OF 'SHORT', 'LONG', 'DATES',
'OFFLINE', 'PATH', OR 'SECURITY'. SYNTAX
'SHOW=showparm[,showparm....]' (S/R 455)
CAUSE You did not type a valid show parameters.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
456 MESSAGE EXPECTED showparm FOR THE 'SHOW' OPTION.
EXPECTED ONE OF 'SHORT', 'LONG', 'DATES',
'OFFLINE', 'PATH', OR 'SECURITY'. SYNTAX
'SHOW=showparm[,showparm....]' (S/R 456)
CAUSE You type the show parameters incorrectly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------