HP 3000 Manuals HP 3000 Manuals
(S/R) (contd.)
188 MESSAGE VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
CAUSE A different labeled volume than the one requested
was mounted for a store.
ACTION Dismount this volume and mount the requested
volume.
---------------------------------------------------------------
189 MESSAGE VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
CAUSE A different labeled volume than the one requested
was mounted for a store.
ACTION Dismount this volume and mount the requested
volume.
---------------------------------------------------------------
190 MESSAGE VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED
CAUSE A different labeled volume than the one requested
was mounted for a store.
ACTION Dismount this volume and mount the requested
volume.
---------------------------------------------------------------
191 MESSAGE RESTORE SKIPPING SLT IN PROGRESS ON LDEV !
CAUSE Restore is skipping over the SLT portion of
combined SLT/Store.
ACTION Information only.
---------------------------------------------------------------
198 MESSAGE OK TO RESTORE FILES OF SET ! ON LDEV ! (Y/N)
CAUSE Restore needs verification that the specified
restoreset should be restored from the MO at the
specified ldev.
ACTION Reply Yes to the console message if this is the set
that should be restore. Reply No otherwise.
---------------------------------------------------------------
301 MESSAGE WARNING: 'FILES' OPTION HAS BEEN REDUNDANTLY
SPECIFIED (S/R 301)
CAUSE The FILES option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
302 MESSAGE EXPECTED '={maxfiles}' AFTER 'FILES' OPTION.
SYNTAX
'FILES={maxfiles}' (S/R 302)
CAUSE You did not type the files parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
303 MESSAGE SPECIFIED MAXFILES VALUE FOR 'FILES={maxfiles}'
EXCEEDS THE MAXIMUM ALLOWED. (S/R 303)
CAUSE The maximum files limit of the files parameter has
been exceeded.
ACTION Information only.
---------------------------------------------------------------
304 MESSAGE EXPECTED 'FILES={maxfiles}' WHERE {maxfiles} IS A
POSITIVE INTEGER. (S/R 304)
CAUSE You have specified a negative 'maxfiles' number.
ACTION Information only.
---------------------------------------------------------------
305 MESSAGE 'FILES' OPTION CANNOT BE USED WITH THE 'LISTDIR'
OPTION. (S/R 305)
CAUSE The files and listdir options are not allowed on
the same command line.
ACTION Delete either the files or the listdir options.
---------------------------------------------------------------
311 MESSAGE 'RESTORESET' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 311)
CAUSE You entered RESTORESET twice in the command.
ACTION Remove one of the RESTORESET options and retype the
command.
---------------------------------------------------------------
312 MESSAGE 'RESTORESET' OPTION MAY NOT BE SPECIFIED IN
CONJUNCTION WITH A POSITIONAL DEVICE FILE. Ex.
'RESTORE *t;....;RESTORESET=(*t1,*t2)' IS INVALID.
(S/R 312)
CAUSE Restoreset and device file options are not allowed
on the same command line.
ACTION Delete either restoresest or device file options
and retype the command.
---------------------------------------------------------------
313 MESSAGE EXPECTED '=(device[,,..])[,(device[,...])]' AFTER
'RESTORESET' OPTION. SYNTAX
'RESTORESET=(device[,..])[,(device[,...])]'. (S/R
313)
CAUSE You did not type the restoreset parameter
correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
314 MESSAGE EXPECTED A '(' TO START A RESTORESET. Ex.
'RESTORESET=(*ta,*tb). SYNTAX
'RESTORE-SET=(device[,...])[device[,...])]' (S/R
314)
CAUSE You did not include a left parenthesis.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
315 MESSAGE MAXIMUM NUMBER OF PARALLEL SETS EXCEEDED FOR
'RESTORESET' OPTION. Ex, 'RESTORESET=(*ta),(*tb)'
IS TWO PARALLEL SETS. (S/R 315)
CAUSE You specified too many parallel sets. The maximum
is 8.
ACTION Specify 8 or fewer parallel sets.
---------------------------------------------------------------
316 MESSAGE EXPECTED 'device' FILE EQUATION IN RESTORESET.
Ex. RESTORESET=(*t SYNTAX
'RESTORESET=(device[,..])[,(device[,...])]'. (S/R
316)
CAUSE You did not include a file equation to name the
backup device.
ACTION Specify a file equation.
---------------------------------------------------------------
317 MESSAGE MAXIMUM NUMBER OF 'device" FILE EQUATIONS
EXCEEDED FOR A SERIAL SET. Ex. RESTORESET = (*t1,
*t2,..., *tn) EXCEEDS THE MAXIMUM OF 8. (S/R 317)
CAUSE You specified too many serial file equations. The
maximum is 8.
ACTION Specify 8 or fewer serial file equation.
---------------------------------------------------------------
318 MESSAGE EXPECTED A ')' TO TERMINATE A SERIAL THE
'RESTORESET' OPTION. SYNTAX
'RESTORESET=(device[,...])[device[,...])]' (S/R
318)
CAUSE You did not include a right parenthesis.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
319 MESSAGE 'RESTORESET' OPTION CANNOT BE USED WITH THE
'LISTDIR' OPTION. (S/R 319)
CAUSE Restoreset and listdir options are not allowed on
the same command line.
ACTION Delete either restoreset or listdir option and
retype the command.
---------------------------------------------------------------
320 MESSAGE 'RESTORESET' OPTION NOT ALLOWED FOR A SLT/STORE
SET (S/R 320)
CAUSE The restoreset option cannot be used with a
combined SLT/ store set tape.
ACTION Redo the restore command, using only one backup
device, and not specifying the restoreset option.
---------------------------------------------------------------
321 MESSAGE WARNING: 'PROGRESS' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 321)
CAUSE The PROGRESS option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
322 MESSAGE EXPECTED {#minutes} BETWEEN 1 AND 60. SYNTAX
PROGRESS[={#minutes}] (S/R 322)
CAUSE You did not specify a number within the range.
ACTION Specify a number between 1 and 60.
---------------------------------------------------------------
323 MESSAGE EXPECTED 'PROGRESS={#minutes}' WHERE {#minutes}
IS A POSITIVE INTEGER. (S/R 323)
CAUSE The progress parameter must be greater than zero.
ACTION Check your syntax and retype the command.
---------------------------------------------------------------
324 MESSAGE EXPTECTED '={#minutes}' AFTER 'PROGRESS' OPTION.
(S/R 324)
CAUSE You did not type the progress parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
331 MESSAGE 'STORESET' OPTION CANNOT BE USED WITH 'TRANSPORT'
TO MPEv. (S/R 331)
CAUSE You cannot specify the storeset and transport
parameters on the same command line.
ACTION Delete either the storeset or the transport
parameter from the command line.
---------------------------------------------------------------
332 MESSAGE 'STORESET' OPTION HAS BEEN REDUNDANTLY SPECIFIED.
(S/R 332)
CAUSE You entered STORESET twice in the command.
ACTION Delete one of the STORESET options and retype the
command.
---------------------------------------------------------------
333 MESSAGE 'STORESET' OPTION MAY NOT BE SPECIFIED IN
CONJUNCTION WITH A POSITIONAL DEVICE FILE. EG
'STORE...;*t;STORESET=(*t1,*t2)' IS VALID. (S/R
333)
CAUSE You mistyped the storeset parameter.
ACTION Check the syntax of the storeset parameter and
retype the command.
---------------------------------------------------------------
334 MESSAGE EXPECTED '=(device[,,..])[,(device[,...])]' AFTER
'STORESET' OPTION. SYNTAX
'STORESET=(device[,..])[,(device[,...])]' (S/R
334)
CAUSE You did not type the storeset parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
335 MESSAGE EXPECTED A '(' TO START A STORESET. Ex.
'STORESET=(*ta,*tb). SYNTAX
'STORESET=(device[,...])[,(device[,...])]' (S/R
336)
CAUSE You did not include the left parenthesis in your
command.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
336 MESSAGE EXPECTED 'device' FILE EQUATION IN STORESET. Ex.
STORESET=(*ta,*tb SYNTAX
'STORESET=(device[,..])[,(device[,...])]' (S/R
336)
CAUSE You did not specify a file equation to name the
backup device.
ACTION Specify the file equation.
---------------------------------------------------------------
337 MESSAGE MAXIMUM NUMBER OF 'device' FILE
EQUATIONS EXCEEDED FOR A SERIAL SET. Ex.
STORESET=(*t1,*t2,...*tn) EXCEEDS THE MAXIMUM OF
8. (S/R 337)
CAUSE You specify too many serial file equations. the
maximum is 8.
ACTION Specify 8 or fewer serial file equations.
---------------------------------------------------------------
338 MESSAGE EXPECTED A ')' TO TERMINATE A SERIAL THE
'STORESET' OPTION. SYNTAX
'STORESET=(device[,...])[(device[,...])]' (S/R 338)
CAUSE You did not include a right parenthesis.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
339 MESSAGE 'STORESET' OPTION NOT ALLOWED IN SYSGEN/STORE.
(S/R 339)
CAUSE A combined SLT/store set cannot be created by
sysgen with the storeset option.
ACTION Retype the command without the storeset option,
specifying only one backup device.
---------------------------------------------------------------
351 MESSAGE WARNING: 'TRANSPORT' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 351)
CAUSE The TRANSPORT option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
352 MESSAGE 'TRANSPORT' OPTION NOT ALLOWED IN SYSGEN/STORE.
(S/R 352)
CAUSE Sysgen cannot created a CMStore format tape.
ACTION Remove the transport option from the store options
and redo the command.
---------------------------------------------------------------
354 MESSAGE INVALID TARGET SYSTEM ID FOR 'TRANSPORT' KEYWORD.
ONLY ID CURRENTLY VALID IS "MPEXL". IF NO TARGET
ID IS SPECIFIED THEN THE TARGET SYSTEM DEFAULTS TO
MPEv. SYNTAX: TRANSPORT[=MPEXL] (S/R 354)
CAUSE An invalid transport id was specified.
ACTION Specify a legel transport option and redo the
command.
---------------------------------------------------------------
361 MESSAGE WARNING: 'DIRECTORY' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 361)
CAUSE The DIRECTORY option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
362 MESSAGE 'DIRECTORY' OPTION CANNOT BE USED WITH THE
'TRANSPORT' OPTION. (S/R 362)
CAUSE Directory and transport options are not allowed on
the same command line.
ACTION Delete either directory or transport option and
retype the command.
---------------------------------------------------------------
363 MESSAGE USE OF THE 'DIRECTORY' OPTION REQUIRES (SM) OR
(OP) CAPABILITY. (S/R 363)
CAUSE You do not have system manager (SM) capability or
system operator (OP) capability.
ACTION Log on to an account with SM or AM, or have your
system manager perform the tasks.
---------------------------------------------------------------
371 MESSAGE 'ONVS' OPTION CANNOT BE USED WITH 'TRANSPORT' TO
MPEv. (S/R 371)
CAUSE ONVS and TRANSPORT options are not allowed on the
same command line.
ACTION Delete either the ONVS or TRANSPORT option and
retype the command.
---------------------------------------------------------------
372 MESSAGE WARNING: 'ONVS' OPTION HAS BEEN REDUNDANTLY
SPECIFIED. (S/R 372)
CAUSE The ONVS option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
373 MESSAGE EXPECTED '=volumesetname[,volumesetname...]'
AFTER 'ONVS' OPTION. (S/R 373)
CAUSE You did not type the onvs parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
374 MESSAGE INVALID VOLUMESET NAME SPECIFIED FOR 'ONVS'
OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A
- Z' AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_"
AND "." SYNTAX
'ONVS=volumesetname[,volumesetname...]'. (S/R 374)
CAUSE Volumeset name mispelled or not recognized on the
system.
ACTION Enter a system recognized volumeset name.
---------------------------------------------------------------
375 MESSAGE VOLUMESET NAME SPECIFIED FOR 'ONVS' OPTION
EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32
CHARACTERS. SYNTAX
'ONVS=volumesetname[,volumesetname...]'. (S/R 375)
CAUSE You entered a volumeset name that was more than 32
characters.
ACTION Enter a volumeset name that has 32 characters or
less.
---------------------------------------------------------------
376 MESSAGE EXPECTED 'volumesetname[,volumesetname...]' AFTER
'ONVS=' WHERE volumesetname IS THE NAME OF THE
VOLUME SET THAT IS CURRENTLY ON YOUR SYSTEM. SYNTAX
'ONVS=volumesetname[,volumesetname...]'. (S/R 376)
CAUSE You did not type onvs parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
377 MESSAGE STORE/RESTORE DOES NOT ALLOW MORE THAN TWENTY
(20) "volumesetnames" TO BE SPECIFIED FOR THE
'ONVS' OPTION. (S/R 377)
CAUSE You specify too many volumeset name with the onvs
option. the maximum is 20.
ACTION Specify 20 or fewer volumesets.
---------------------------------------------------------------
378 MESSAGE "volumesetname" SPECIFIED DOES NOT EXIST (IS NOT
MOUNTED) ON THIS SYSTEM. (S/R 378)
CAUSE You entered a volumeset name which is not on the
system.
ACTION Enter a correct volumeset name.
---------------------------------------------------------------
381 MESSAGE 'VOLSET' OPTION HAS BEEN REDUNDANTLY SPECIFIED.
(S/R 381)
CAUSE The VOLSET option was entered more than once.
ACTION Information only.
---------------------------------------------------------------
382 MESSAGE 'VOLSET' OPTION CANNOT BE USED WITH THE 'DEV'
OPTION. (S/R 382)
CAUSE Volset and dev options are not allowed on the same
command line.
ACTION Delete either volset or dev option and retype the
command.
---------------------------------------------------------------
383 MESSAGE EXPECTED '=volumesetname' AFTER 'VOLSET' OPTION.
SYNTAX
'VOLSET=volumesetname'. (S/R 383)
CAUSE You did not enter the volset parameter correctly.
ACTION Check the syntax and retype the command.
---------------------------------------------------------------
384 MESSAGE INVALID VOLUMESET NAME SPECIFIED FOR 'VOLSET'
OPTION. VOLUMESET NAME MUST START WITH AN ALPHA
"A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_"
OR "." SYNTAX
'VOLSET=volumesetname'. (S/R 384)
CAUSE Volumeset name mispelled or not recognized on the
system.
ACTION Enter a system recognized volumeset name.
---------------------------------------------------------------
385 MESSAGE VOLUMESET NAME SPECIFIED FOR 'VOLSET' OPTION
EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32
CHARACTERS. SYNTAX
'VOLSET=volumesetname' (S/R 385)
CAUSE You entered a volumeset name that was more than 32
characters.
ACTION Enter a volumeset name that has 32 characters or
less.
---------------------------------------------------------------