HP 3000 Manuals HP 3000 Manuals
Sending Jobs to a Host
To operate NRJE you must do the following:
* Log on to the HP 3000.
* Optionally define any formal designators you will use.
* Invoke NRJE.
* Issue a SUBMIT command.
Defining Formal Designators
Define formal file designators with a FILE command. You can do this
before you invoke NRJE, or within NRJE. When a formal designator is used,
it must be preceded by an asterisk (*). The asterisk indicates a
reference to a previous FILE command. See the MPE Commands Reference
Manual or the MPE Software Pocket Guide.
NRJE Command
Invoke NRJE NRJE command from MPE by issuing the command
: NRJE Wsid
where Wsid is a workstation identifier. See NRJE in Chapter 3, "User
Commands."
When you use NRJE as an MPE command you can omit the workstation
identifier; however, you must use a Wsid parameter in every command that
refers to a workstation.
Kinds of NRJE Users
NRJE users can perform the following tasks:
* Transmit and receive batch jobs between an HP 3000 serving as a
workstation and a host system. No special HP 3000 user capabilities
are required.
* Control an HP 3000 workstation. NM user capability is required.
Users configured with NM capability can be NRJE managers.
An NRJE manager can do everything a user can do. Some user commands have
NRJE manager extensions.
Sample NRJE Session on an HP 3000
See Chapter 3, "User Commands," for a description of each of the commands
in the following sample session. In this sample, user input is shown in
shaded text, and instructions and explanations are in italics.
__________________________________________________________________________________
| |
| Log onto the HP 3000 |
| |
| :HELLO USER.ACCT,GROUP |
| WELCOME TO THE HP 3000 |
| |
| Invoke the NRJE subsystem by entering the NRJE |
| command and specifying RMT11 as the |
| default workstation identifier. |
| |
| :NRJE RMT11 |
| |
| A banner line identifies NRJE and its version. |
| |
| product number version number NJRE (C) HEWLETT-PACKARD CO. copyright year |
| |
| An NRJE welcome message follows the banner line. |
| The text of this message is configured by an |
| RJE manager. |
| |
| WELCOME TO NRJE |
| |
| A configured prompt string, RMT11 is sent by NRJE.|
| This identifies your default workstation. |
| |
| RMT11>... |
| |
| Now you can issue an NRJE subsystem command. |
__________________________________________________________________________________
Figure 2-4. Sample NRJE Session
_____________________________________________________________________________
| |
| A two-line SUBMIT command is entered next. |
| An ampersand (& ) continues the command to |
| a second line. File identifiers follow the |
| command. All files are from your logon group|
| and account. |
| |
| RMT11>SUBMIT FRONTJCL, DATA1, DATA2,& |
| RMT11>BACKJCL |
| |
| A message is displayed indicating that your |
| job stream has been constructed and is |
| ready to be sent to the host system. |
| |
| Note the number in the message (1042) for |
| future reference, or use the job naming |
| capabilities of the SUBMIT command. |
| |
| JOB SUCCESSFULLY SUBMITTED. THE SPOOL FILE IS: |
| #O1042 |
| |
| Now you can issue other NRJE commands. |
| |
| RMT11>... |
| |
| Issue an EXIT command which returns |
| control to MPE. |
| |
| RMT11>...EXIT |
| |
| Your MPE prompt is returned and you can issue|
| MPE commands. |
| |
| :... |
_____________________________________________________________________________
Figure 2-4. Sample NRJE Session (cont.)
You may want to find out about the jobs you have submitted, cancel your
jobs, or change their transmission priority. The commands available for
these tasks are described in Chapter 3, "User Commands." Table 3-1, "NRJE
User Commands," summarizes all of the routine commands. (Manager
commands required for day-to-day workstation operations are described in
the SNA NRJE Node Manager's Guide.)