Switch (Subsystem 100)
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III ♥ | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
- 20
- MESSAGE
Switch to CM was attempted with an illegal method.
- CAUSE
Bad value in method parameter.
- ACTION
Use one of the legal methods.
- 30
- MESSAGE
Not enough room in CM stack to complete switch to CM.
- CAUSE
Too much room required to move parameter to the CM stack.
- ACTION
Change the program so there is more room left on CM stack before switching.
- 40
- MESSAGE
Illegal number of parameters were encountered.
- CAUSE
The parameter specifying the number of parameters to pass to CM was not within the legal values.
- ACTION
Specify a legal value.
- 50
- MESSAGE
Illegal parameter length was encountered.
- CAUSE
Negative or zero length parameter specified.
- ACTION
Change parameter length.
- 60
- MESSAGE
Illegal privileged operation.
- CAUSE
A switch was made to CM in METHOD_SPLIT by a user mode program.
- ACTION
Link the program with privilege mode.
- 80
- MESSAGE
Procedure specification is illegal.
- CAUSE
Switch to CM is not by ID, NAME or PLABEL.
- ACTION
Fix the PROC parameter.
- 90
- MESSAGE
Switch to CM was attempted with an illegal ID number.
- CAUSE
The ID number is out of range.
- ACTION
Correct the ID number in the program.
- 110
- MESSAGE
The SWITCH to CM PLABEL HASH TABLE is full.
- CAUSE
Table to cache names of dynamically loaded CM procedures is full.
- ACTION
Do not dynamically load so many procedures.
- 120
- MESSAGE
The CM procedure is not in the CM procedure/PLABEL HASH TABLE.
- CAUSE
The table does not exist or the CM procedure has not been loaded.
- ACTION
Check the table name or load the CM procedure.
- 130
- MESSAGE
Invalid status parameter.
- CAUSE
Either the LOAD_CM_PROCEDURE or the UNLOAD_CM_PROCEDURE failed.
- ACTION
Check procedure name or library search parameters.
- 150
- MESSAGE
Illegal PROC address in SWITCH to CM.
- CAUSE
User does not have the capability to access the area containing the PROC record (in HPSWITCH TO CM).
- ACTION
Put the PROC in an accessible area.
- 152
- MESSAGE
Illegal parameter record address.
- CAUSE
User does not have the capability to access the area containing the PARMS record (in HPSWITCH TO CM).
- ACTION
Put the parameter in an accessible area.
- 154
- MESSAGE
Illegal parameter address.
- CAUSE
User does not have the capability to access a parameter specified in the PARMS record (in HPSWITCH TO CM).
- ACTION
Put the parameter in an accessible area.
- 156
- MESSAGE
Illegal PD_PARM_TYPE.
- CAUSE
An illegal PD_PARM_TYPE was specified in a PARMS record entry (in HPSWITCH TO CM).
- ACTION
Use a legal type.
- 158
- MESSAGE
Illegal I/O specification.
- CAUSE
A reference parameter is not input or output in a reference parameter in a PARMS record entry (in HPSWITCH TO CM).
- ACTION
Specify input, output or both.
- 160
- MESSAGE
Illegal function return length.
- CAUSE
The function length parameter was negative or greater than the CM stack (64 Kbytes).
- ACTION
Specify a legal length.
- 162
- MESSAGE
Illegal function return address.
- CAUSE
The user does not have the right to access the area specified by the function address and function length.
- ACTION
Specify an accessible area for the function.
- 164
- MESSAGE
Illegal function return specification.
- CAUSE
The function length was > 0 and nil return or address of length = 0 and NON_NIL return address.
- ACTION
Specify a legal function length and address.
- 166
- MESSAGE
Illegal condition code address.
- CAUSE
The user does not have the right to access the address specified for the return of the condition code.
- ACTION
Specify an accessible address for the condition code.
- 168
- MESSAGE
Illegal status address.
- CAUSE
The user does not have the right to access the area used for the return of the status.
- ACTION
Specify a legal address.
- 200
- MESSAGE
The SWITCH to NM was attempted with an illegal function type.
- CAUSE
The parameter specifying the function type to be returned was not one of the legal types.
- ACTION
Use a legal function type.
- 210
- MESSAGE
An illegal PARM type was encountered while switching to NM.
- CAUSE
An argument descriptor contained a type that was not legal.
- ACTION
Use a legal type.
- 250
- MESSAGE
An illegal number of arguments was passed to SWITCH to NM.
- CAUSE
The parameter specifying the number of arguments was not within the legal range.
- ACTION
Use a legal number of arguments.
- 270
- MESSAGE
The SWITCH to NM method is illegal.
- CAUSE
Switch to NM is not by ID, NAME or PLABEL.
- ACTION
Use a legal method.
- 290
- MESSAGE
A FINDPROC error occurred while switching to NM.
- CAUSE
FINDPROC failed to load the procedure requested.
- ACTION
Make sure the loader can find your procedure to load.
- 300
- MESSAGE
The byte reference parameter is not 16-bit aligned.
- CAUSE
SWITCH to CM with METHOD_NOCOPY and a byte reference parameter that is not 16-bit aligned.
- ACTION
Recode program to align the parameter or use METHOD_SPLIT to SWITCH to CM.
- 330
- MESSAGE
Unable to swap parameters in NO_COPY method.
- CAUSE
Parameters could not be enclosed within a DST because the parameters are too far apart.
- ACTION
Move parameters closer together.
|
SUSPEND |
Symbolic Debugger |