NLIOUTIL
MPE documents | |
 Complete PDF | |
| Table of Contents | |
| E0701 Volume II | |
| E0300 Volume I | |
| E0300 Volume II | |
| E0300 Volume III ♥ | |
| E0394 Volume I | |
| E0796 Volume II | |
| E0494 Volume III |
- 11
- MESSAGE
TERMINAL n IS SHUT.
- 12
- MESSAGE
PRINTER n IS SHUT.
- 21
- MESSAGE
TERMINAL n IS OPENED IN LANGUAGE n.
- 22
- MESSAGE
PRINTER n IS OPENED WITH LANGUAGE n.
- 31
- MESSAGE
TERMINAL n IS OPENED WITH LANGUAGE n, RECCONV.
- 32
- MESSAGE
TERMINAL n IS OPENED WITH LANGUAGE n, NORECCONV.
- 33
- MESSAGE
PRINTER n IS OPENED WITH LANGUAGE n, RECCONV.
- 34
- MESSAGE
PRINTER n IS OPENED WITH LANGUAGE n, NORECCONV.
- 35
- MESSAGE
LATIN MODE, WIDTH = n, SHAPE = n.
- 36
- MESSAGE
NONLATIN MODE, WIDTH = n, SHAPE = n.
- 41
- MESSAGE
TERMINAL n : LANGUAGE IS SET TO n.
- 42
- MESSAGE
PRINTER n : LANGUAGE IS SET TO n.
- 51
- MESSAGE
TERMINAL n : RECCONV IS SET.
- 52
- MESSAGE
TERMINAL n : NORECCONV IS SET.
- 61
- MESSAGE
PRINTER n : RECCONV IS SET.
- 62
- MESSAGE
PRINTER n : NORECCONV IS SET.
- 71
- MESSAGE
PRINTER n : LATIN MODE IS SET.
- 72
- MESSAGE
PRINTER n : NONLATIN MODE IS SET.
- 81
- MESSAGE
PRINTER n : WIDTH IS SET TO n.
- 91
- MESSAGE
PRINTER n : SHAPE IS SET TO n.
- 1200
- MESSAGE
TERMINAL n IS ALREADY OPENED. (NLIO WARN 1200)
- 1201
- MESSAGE
PRINTER n IS ALREADY OPENED. (NLIO WARN 1201)
- CAUSE
You tried to OPEN a device which was already OPENed.
- ACTION
Use the SHOW command to check the status. Check the ldev.
- 1202
- MESSAGE
TERMINAL n IS CONTROLLED BY OTHER PROCESS. (NLIO WARN 1202)
- CAUSE
Same as message.
- ACTION
Re-try the same command.
- 1204
- MESSAGE
TERMINAL n IS IN USE, SHUT PENDING. (NLIO WARN 1204)
- CAUSE
Same as message.
- ACTION
No action required.
- 1205
- MESSAGE
PRINTER n IS IN USE, SHUT PENDING. (NLIO WARN 1205)
- CAUSE
Same as message.
- ACTION
No action required.
- 1206
- MESSAGE
TERMINAL n HAS NOT BEEN OPENED YET. (NLIO WARN 1206)
- CAUSE
You tried to SHUT a device which was not OPENed. Or, a device which you SHOWed was not OPENed.
- ACTION
Check the ldev if necessary
- 1207
- MESSAGE
PRINTER n HAS NOT BEEN OPENED YET. (NLIO WARN 1207)
- CAUSE
You tried to SHUT a device which was not OPENed. Or, a device which you SHOWed was not OPENed.
- ACTION
Check the ldev if necessary
- 1208
- MESSAGE
NO TERMINAL/PRINTER HAS BEEN OPENED. (NLIO WARN 1208)
- CAUSE
You tried to SHUT devices, or SHOWed the status when no device had been OPENed.
- ACTION
No action is required.
- 1211
- MESSAGE
TERMINAL n IS SHUT PENDING. (NLIO WARN 1211)
- CAUSE
Same as message.
- ACTION
No action required.
- 1212
- MESSAGE
PRINTER n IS SHUT PENDING. (NLIO WARN 1212)
- CAUSE
Same as message.
- ACTION
No action required.
- 1300
- MESSAGE
"NLIODEF.PUB.SYS" FILE BEING ACCESSED. (NLIO WARN 1300)
- 2100
- MESSAGE
UNKNOWN COMMAND WAS ENTERED. (NLIO ERR 2100)
- CAUSE
Command name incorrect.
- ACTION
Re-enter the command. Use HELP to check the syntax.
- 2101
- MESSAGE
TOO MANY PARAMETERS WERE ENTERED. (NLIO ERR 2101)
- CAUSE
Same as message.
- ACTION
Re-enter the command using the correct syntax. Use HELP to check the syntax.
- 2102
- MESSAGE
INVALID DELIMITER WAS ENTERED. (NLIO ERR 2102)
- CAUSE
The second OPEN delimeter is incorrect.
- ACTION
Re-enter the command using the correct syntax. Use HELP to check the syntax.
- 2110
- MESSAGE
LDEV CANNOT BE OMITTED FOR NON-INTERACTIVE STDIN. (NLIO ERR 2110)
- CAUSE
Same as message.
- ACTION
Re-enter the command, specifying the ldev.
- 2111
- MESSAGE
NO DEVICE IS DESIGNATED FOR SPECIFICED DEVICE. (NLIO ERR 2111)
- CAUSE
The device or device class specified does not refer to a configured device.
- ACTION
Check the system configuration and re-enter the command, specifying the correct ldev.
- 2113
- MESSAGE
SPECIFIED LDEV n IS NOT A TERMINAL OR PRINTER. (NLIO ERR 2113)
- CAUSE
The specified ldev was other than a terminal or a printer.
- ACTION
Check the system configuration and re-enter the command, specifying the correct ldev.
- 2114
- MESSAGE
SPECIFIED DEVICE CLASS IS NOT A TERMINAL OR PRINTER. (NLIO ERR 2114)
- CAUSE
The specified device class does not apply to terminals or printers.`
- ACTION
Check the system configuration and re-enter the command, specifying the correct device class.
- 2115
- MESSAGE
INVALID PARAMETER WAS ENTERED. (NLIO ERR 2115)
- CAUSE
The specified ldev was other than a terminal or a printer.
- ACTION
Check the system configuration and re-enter the command, specifying the correct ldev.
- 2116
- MESSAGE
TMUX TERMINAL WAS SPECIFIED. (NLIO ERR 2116)
- 2120
- MESSAGE
INVALID LANGUAGE WAS ENTERED. (NLIO ERR 2120)
- CAUSE
The input language ID was not a valid one.
- ACTION
Check the language ID and re-enter the command, specifying a correct language ID.
- 2121
- MESSAGE
UNKNOWN LANGUAGE WAS ENTERED. (NLIO ERR 2121)
- CAUSE
Unsupported language ID was entered. as the system default language.
- ACTION
Check the language ID and re-enter the command.
- 2122
- MESSAGE
INVALID LANGUAGE IS USED. (NLIO ERR 2122)
- CAUSE
Unsupported language ID was set as the user interface language set, or as the system default language.
- ACTION
Re-enter the command, specifying the correct language ID.
- 2123
- MESSAGE
SPECIFIED LANGUAGE IS NOT CONFIGURED ON THE SYSTEM. (NLIO ERR 2123)
- CAUSE
The specified language is not supported on the system.
- ACTION
Check and set the valid language, then re-enter the command.
- 2130
- MESSAGE
INVALID WIDTH PARAMETER WAS ENTERED. (NLIO ERR 2130)
- 2131
- MESSAGE
INVALID WIDTH VALUE WAS ENTERED. (NLIO ERR 2131)
- 2140
- MESSAGE
INVALID SHAPE PARAMETER WAS ENTERED. (NLIO ERR 2140)
- 2141
- MESSAGE
INVALID SHAPE VALUE WAS ENTERD. (NLIO ERR 2141)
- 2150
- MESSAGE
UNKNOWN COMMAND FOR HELP. (NLIO ERR 2150)
- CAUSE
You entered a command that HELP does not recognize.
- ACTION
Check the valid command names by entering the HELP command without any parameters. Then re-enter the HELP command using the correct parameter.
- 2160
- MESSAGE
BOTH RECCONV AND NORECCONV PARAMETER WERE ENTERED. (NLIO ERR 2160)
- 2161
- MESSAGE
BOTH LATIN AND NONLATIN PARAMETER WERE ENTERED. (NLIO ERR 2161)
- 2162
- MESSAGE
REDUNDANT RECCONV PARAMETER. (NLIO ERR 2162)
- 2163
- MESSAGE
REDUNDANT NORECCONV PARAMETER. (NLIO ERR 2163)
- 2164
- MESSAGE
REDUNDANT LATIN PARAMETER. (NLIO ERR 2164)
- 2165
- MESSAGE
REDUNDANT NONLATIN PARAMETER. (NLIO ERR 2165)
- 2166
- MESSAGE
REDUNDANT WIDTH PARAMETER. (NLIO ERR 2166)
- 2167
- MESSAGE
REDUNDANT SHAPE PARAMETER. (NLIO ERR 2167)
- 2170
- MESSAGE
LANGUAGE WAS NOT ASIAN LANGUAGE. (NLIO ERR 2170)
- 2171
- MESSAGE
LANGUAGE WAS NOT MEA LANGUAGE. (NLIO ERR 2171)
- 2180
- MESSAGE
TERMINAL CANNOT BE OPENED WITH MEA LANGUAGE. (NLIO ERR 2180)
- 2201
- MESSAGE
OP CAPABILITY IS REQUIRED. (NLIO ERR 2201) OP capability is required to specify an STDIN other than your own. You currently do not have OP capability. Check the ldev, or contact your System Manager to extend your capabilities.
- 2300
- MESSAGE
MISSING MESSAGE CATALOG FILE = NLIOCAT.PUB.SYS. (NLIO ERR 2300) The message catalog for the NLIOUTIL program is missing. Contact your System Manager to locate the message catalog.
- 2301
- MESSAGE
MISSING "NLIODEF.PUB.SYS FILE". (NLIO ERR 2301)
|
Native Mode Device File (Subsystem 231) |
Parser |