KSAM (Subsystem 143)

NOTE: KSAM error messages are included with subsystem 143 (File System) messages. Refer to chapter 4, File System (Native Mode), for listing of messages.

1026

MESSAGE

Type manager; an internal error occurred.

CAUSE

You requested a lower level system service and this reported an error to the type manager.

ACTION

If the problem persists, contact your Hewlett-Packard support engineer.

1079

MESSAGE

TM_KSM_INVALID_OFFSET

CAUSE

The file offset pointer calculated for the KSAM file is invalid.

ACTION

Close the KSAM file, store it to tape, and call your Hewlett-Packard support representative.

1080

MESSAGE

TM_KSM_UNEXPECTED_ERROR

CAUSE

During an operation on a KSAM file, a non-file system error occurred.

ACTION

Close the KSAM file, store it to tape, and call your Hewlett-Packard support representative.

6005

MESSAGE

Type manager; invalid function code or parameter.

CAUSE

An FCONTROL or FDEVICECONTROL function, or one of its parameters, is not valid for the particular device or access method in which it was used. It may also be invalid for any device (for example, out of range).

ACTION

Check the intrinsic call for which the error is reported and correct any errors in the calling sequence.

6006

MESSAGE

Type manager; you specified a parameter value that is more than the maximum specified for this
function.

CAUSE

Self-explanatory.

ACTION

Use the MPE XL Intrinsics manual to verify the set of acceptable parameters for a given function code.

6007

MESSAGE

Type manager; you specified a parameter value that is less than the minimum specified for this function.

CAUSE

Self-explanatory.

ACTION

Use the MPE XL Intrinsics manual to verify the set of acceptable parameters for a given function code.

6013

MESSAGE

Type manager; device is off-line.

CAUSE

For printers attached via the Distributed Terminal Controller (DTC), this is a generic error indicating the inability of the DTC to communicate with its device. It is currently not returned for other devices.

ACTION

Check the DTC-to-device cable connections, parity and baud rate settings, DTR and CTS settings, and Transmit/Receive Pacing settings. Ensure that they are set as required for proper use by the DTC.

6022

MESSAGE

Type manager; unit failure.

CAUSE

An undetermined device or transmission error occurred.

ACTION

Check lower level statuses to determine the root cause of the error.

6025

MESSAGE

Type manager; timeout while waiting for I/O completion.

CAUSE

This usually indicates a hardware failure of some component of the I/O subsystem.

ACTION

Contact your Hewlett-Packard support engineer.

6026

MESSAGE

Type manager; data transmission error.

CAUSE

An undetermined transmission error was reported by a lower level subsystem.

ACTION

Check the lower level statuses to determine the root cause of the error.

6029

MESSAGE

Type manager; the device reported a power-up.

CAUSE

Self-explanatory. For printers, this status is returned only if device status reporting is disable (the default). If it is enabled, the intrinsic interface returns CCG instead, indicating that status is available.

ACTION

The application or operator should take whatever steps are appropriate (for example, putting the device on line). For printers, the Native Mode Spooler will attempt to recover to the start of the current page.

6035

MESSAGE

Type manager; your I/O request was aborted due to a system power failure.

CAUSE

Self-explanatory.

ACTION

If the device is owned by a spooler, the spooler process will terminate. Restart the process. For other situations, take whatever steps are appropriate to re-establish normal device operation.

6036

MESSAGE

Type manager; data lost.

CAUSE

A lower level subsystem has reported an error of some kind which resulted in an incomplete data transfer.

ACTION

Check the lower level statuses to determine the root cause of the error.

6037

MESSAGE

Type manager; the I/O request was aborted externally.

CAUSE

Either you entered an explicit ABORTIO, or the process with outstanding I/O is being terminated.

ACTION

None.

6039

MESSAGE

Type manager; the device reported a parity error.

CAUSE

Self-explanatory.

ACTION

Take whatever steps are appropriate, for example, cleaning tape heads. If the problem persists, contact your Hewlett-Packard support engineer.