|
|
Collect the tape media you will be using as source material
to modify the system software. The tapes vary depending on your
task, but may include PowerPatch, Reactive Patch, FOS, factory SLT,
and CSLT tapes. Check your tapes to ensure they are not damaged.
If any files are not verified, or if you receive any errors
or warnings, clean your tape drive. (Run the cleaning cartridge
through your DDS drive at least three times.) Then repeat the tape
verification procedure. If your media is bad, contact your local
HP Support Agreement Specialist (SAS).
To verify the tape source media and contents:
Log on from the console with the following conditions:
:HELLO MANAGER.SYS,INSTALL;HIPRI
:OPENQ LP
:STREAMS streams_device
A common streams_device is 10. An LP device must be
configured in SYSGEN. Already spooled and streamed messages
might display.
Issue a file statement:
:FILE TAPE;DEV=TAPE
Notice that you are logged onto the console, and you will need to
enter CTRL-A in order to issue the reply to each tape
request.
Proceed to the section for each type of tape that you will be
using.
PowerPatch Tape
Mount the PowerPatch tape.
Issue the VSTORE command.
:VSTORE *TAPE;@.@.@;SHOW
Reply to the tape request.
VSTORE displays a listing of verified files. These files
are not being restored to disk.
Proceed to the next type of tape that you will be
using.
Reactive Patch Tape
Mount the Reactive tape.
Issue the VSTORE command.
:VSTORE *TAPE;@.@.@;SHOW
Reply to the tape request.
VSTORE displays a listing of verified files. These files
are not being restored to disk.
Proceed to the next type of tape that you will be
using.
Add-on (SUBSYS) Tape
Mount the SUBSYS tape for your ordered products.
Restore the T-file. This file contains the listing of files
of the purchased products.
:RESTORE *TAPE;T#####.PROD.SOFTREP;CREATE;SHOW
RESTORE returns a T-file, note the T-file filename. If
the T-file is not on the tape:
:RESTORE *TAPE;PRODLIST.MITBLD.SUPPORT
View the T-file using a text editor or word processor.
Print the list of products on the SUBSYS tape.
:FILE LP;DEV=LP
:PRINT Tnnnnn.PROD.SOFTREP >*LP
where Tnnnnn is the name of the file
restored in Step a above.
-
:VSTORE *TAPE;@.@.@;SHOW
If you are doing an Update task proceed to Step 7.
If you are not doing an Update, go to the next task on your
checklist.
Update Tape
If you are on a remote system and applying a CSLT created from a
CD-ROM, omit this step and proceed to Step 8.
If you are performing an Update with Tape, mount the FOS tape and
validate.
:VSTORE *TAPE;@.@.@;SHOW
Mount the FOS tape, if it is not already mounted, and restore
CHECKSLT.
:RESTORE *TAPE; CHECKSLT.MPEXL.TELESUP, &
CKCAT000.MPEXL.TELESUP;SHOW;CREATE
For CKCAT000 the 000 are zeros.
Verify the Factory SLT or CSLT tape.
Mount Factory SLT tape if you are updating the local system,
or mount the CSLT if you are updating a remote system.
Run CHECKSLT.
:CHECKSLT.MPEXL.TELESUP
************************CHECKSLT 1.9**********************
--------------------------------
L E V E L - N U M B E R S
--------------------------------
1 - Check the tape. Display errors and file names.
2 - Check the tape. Display errors, file names and size.
3 - Check the tape and display all information for each
section.
4 - Recover a TAPE BOOT file. NOT AVAILABLE
5 - Recover a DISK file from the tape and copy it to a disk
file.
6 - Check the tape and display the contents of one file in
hex.
7 - Check the tape and display summary of tape and disk use
statistics.
8 - Information.
9 - Exit program.
Which level? __
Select level 1.
Reply to tape request, as required.
checkslt displays a listing of verified files.
|