 |
» |
|
|
|
The following is an explanation of the general format of TCP
logging locations. An explanation of the individual TCP logging
messages follows. Logging Location is a 5-digit decimal field with the following
sub-fields: NMMMM where N is the transport module number and MMMM is defined
by the logging module TCP designates MMMM as follows: TTLL where TT is the type of error which occurred and LL is
a unique location tag used to differentiate between multiple occurrences
of the same error. Module numbers (N) Types (TT) - 00-09
External errors—An error result was returned
from a procedure call to a module outside of TCP.
- 00-
NWTM Error - 01-
NM Ports Error/CM dictionary - 02-
Table Management Error - 03-
Object Management Error - 04-
Path Error - 05-
NET Timers Error - 06-
Semaphores and HPGETSYSPLABEL - 07-
Memory Manager (Freeze, Unfreeze) Error - 08-
NMlog/NMtrace/NMmon/Registry - 09-
Dynamic call to driver (or driver) / HPGETSYSPLABEL
failed
- 10-19
Implementation Errors—These indicate a
coding or data state error somewhere within TCP or the interfaces
to TCP.
- 10-
Attempted to delete from empty rtxq - 11-
Internal IPC State incorrect - 12-
Bad timer state - 13-
Data requested greater than buffer contents - 14-
Bad status from tcp_read_completor - 15-
Unmatched buffer pool in buffer reply - 16-
Unexpected Buffer reply - 17-
Bad buffer reply state - 18-
Resegmentation failure
- 20-29
Remote protocol errors—These errors indicate
that the remote TCP to which this implementation is conversing has
apparently generated a packet which is in error or which violated
the protocol or had to be ignored due to the local state. (Note:
Some of these errors are minor—e.g., Local SAP not open).
- 20-
Inbound Checksum Error - 21-
Inbound Precedence/Security - 22-
Unexpected Syn in window - 23-
No ACK - 24-
Invalid Ack - 25-
Data after Fin - 26-
Bad Max TPDU option length - 27-
Half Open Connection (SIP sent reset) - 28-
Local SAP Not Open
- 30-39
IPC / TCP synchronization errors—IPC has
called TCP with unexpected parameters or in an unexpected state
- 30-
IPC Receive Reply w/o data pending - 31-
IPC Receive Reply while not in data accepting state - 32-
TCP not started - 33-
Network not started - 34-
Bad (Unknown) IPCcontrol
- 40-49
standard connection lost/shutdown errors
- 40-
RTX Timeout (# of retries) - 41-
RTX Threshold exceeded - 42-
Remote abort - 43-
Connection Assurance Timeout
- 50-59
More External Errors—An error result was
returned from a procedure call to a module outside of TCP.
- 50-
Buffer Manager - 59-
Unexpected escape
- 60-79
standard informative errors (etc.)
- 60-
Duplicate Packet received - 61-
Packet tossed - 62-
Retransmission suppressed - 63-
Packet Retransmitted - 64-
Negative Advice Passed - 65-
Late timer - 66-
Source Quench Received
- 70-79
Miscellaneous Errors
- 70-
Duplicate connection name - 71-
Passive Connection Request rejected (or an error
occurred) - 72-
PM Deactivated w/Error - 73-
Duplicate socket name - 74-
Protocol start failed - 75-
Bad Message Type/Function Code - 76-
Max connections exceeded - 77-
Wrong Father Pin (Not NMMON) - 78-
Max sockets exceeded
- 80-89
standard informative messages—Nodal and
connection events
- 80-
PM activated - 81-
PM Graceful released - 82-
PM Deactivated - 83-
Socket Created - 84-
Socket Deactivated - 85-
Protocol started - 86-
Protocol stopped - 87-
Network stopped - 88-
Driver Down Notification Complete - 89-
Path Verify Complete
Title not available (TCP Logging Locations ) - 98-99
Statistical Logging
- 98-
SIP statistics - 99-
PM Statistics
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send the inbound connection
shut request (remote fin received indication) to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send the inbound connection
shut request (remote fin received indication) to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send an irrecoverable error
message to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SET_FILE_EVENT
returned a bad status while trying to set the exception bit due
to received urgent data. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NTWM_SEND_MSG
returned a bad status while trying to notify IPC of received inbound
data. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_RESET_FILE_EVENT
returned a bad status while trying to reset the exception bit due
to coming to the end of inbound urgent data. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send the inbound connection
shutdown request (remote FIN received) to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_RESET_FILE_EVENT
returned a bad status while trying to reset the write bit for a
socket due to coming to the end of inbound connection requests. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_RESET_FILE_EVENT
returned a bad status while trying to reset the write bit for a
connection due to becoming unwritable. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SET_FILE_EVENT
returned a bad status while trying to set the write bit for a connection
due to becoming writable. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send a send completion notification
to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send an irrecoverable error
message to a call socket. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send a connection request
message to IPC. The inbound syn may not be able to establish a connection. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_RESET_FILE_EVENT
returned a bad status while trying to reset the readable bit during
connection cleanup. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_RESET_FILE_EVENT
returned a bad status while trying to reset the readable bit due
to coming to the end of the currently deliverable inbound data. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SEND_MSG
returned a bad status while trying to send a connect reply message
to IPC. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWTM_SET_FILE_EVENT
returned a bad status while trying to set the readable and writable
bits due to a connection shutting down. ACTION: PARM is NWTM
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while sending
a negative advice message to the TCP SIP. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while forwarding
an inbound packet for an unknown connection to the SIP. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a cleanup request to the SIP. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a timer popped message to the SIP due to semaphore contention.
The timer may be dropped, the connection may hang indefinitely. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from a send_msg call while
trying to send an outbound data message to an NI or X.25 port. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from extend_receive while
waiting for a message from the TCP SIP indicating that it has started
successfully. This would occur during network startup. ACTION: Check for other logging
indicating the reason that the SIP was unable to start. PARM is
ports error returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from purge_pool while
trying to delete the TCP SIP message pool. This was during a system
shutdown. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from purge_port while
trying to delete the TCP SIP port. This was during a system shutdown. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from create_pool while
trying to create a message pool for the TCP SIP. This was during
protocol start. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from create_port while
trying to create a port for the TCP SIP. This was during protocol
start. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from change_subqueue while
trying to enable a subset of subqueues for TCP SIP's port. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from purge_pool while
trying to delete a message pool for the TCP SIP. The reason for
deleting the message pool was that an error occurred while bringing
up the TCP SIP, so TCP was cleaning up its resources. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from purge_port while
trying to delete a port for the TCP SIP. The reason for deleting
the port was an error occurred while bringing up the TCP SIP, so
TCP was cleaning up its resources. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a port message to NETCP, which is waiting for reply from
the TCP SIP indicating that has successfully completed initialization.
NETCP is in 'TCP_MODULE_CONFIG'
and may be hung. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a path_verify reply to
NETCP. NETCP may be in a hung state, if so further NETCONTROL
commands will also hang. ACTION: PARM is ports error
returned. Submit an SR. Reboot if necessary to restart transport. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a traceoff_reply message
to NETCP. NETCP may be in a hung state, if so further NETCONTROL
commands will also hang. ACTION: PARM is ports error
returned. Submit an SR. Reboot if necessary to restart transport. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send an outbound data message to the IP port. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a terminate reply message to NETCP. NETCP may be in a hung
state. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from receive_msg while
waiting for a message on the TCP SIP port. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to forward an inbound packet to the SIP. Packet is being forwarded
tracing is active. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from send_msg while trying
to send a cleanup request message to the SIP. ACTION: PARM is ports error
returned. Submit an SR. |
MESSAGE: None | CAUSE: New_get_table_entry
returned a bad status while we were trying to allocate a connection
entry. This occurred while trying to process an inbound syn. The
connection attempt will fail. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_release_table_entry returned
a bad status while we were trying to deallocate a connection entry. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_release_table_entry
returned a bad status while we were trying to deallocate a socket
entry. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_get_table_entry
returned a bad status while we were trying to allocate a socket
entry. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_get_table_entry
returned a bad status while we were trying to allocate a vector
queue entry. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_release_table_entry
returned a bad status while we were trying to deallocate a vector
queue entry. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from new_create_table
while creating the TCP connection table. This would occur during
network startup. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from new_create_table
while creating the TCP socket table. This would occur during network
startup. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from new_create_table
while creating the TCP vector table. This would occur during network
startup. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from delete_table
while releasing the TCP connection table. This would happen after
network or system shutdown. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from delete_table
while releasing the TCP socket table. This would happen after network
or system shutdown. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status returned from delete_table while
releasing the TCP vector table. This would happen after network
or system shutdown. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_get_table_entry returned
a bad status while we were trying to allocate a connection entry.
This occurred while trying to process an inbound syn. The connection
attempt will fail. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: New_release_table_entry
returned a bad status while we were trying to deallocate a connection
entry. The connection entry is being deallocated because a duplicate
connection already exists. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status received from create_object.
Create_object was called during
network startup in order to create the global TCP data area. ACTION: PARM is memory management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: There was
a bad status received from release_object.
Release_object was called because
we had a problem bringing up TCP during network startup, so we were
cleaning up its resources. ACTION: PARM is table management
error returned. Submit an SR. |
MESSAGE: None | CAUSE: PATHs failed
to resolve a path to the requested destination. The connection request
has failed. ACTION: PARM is path resolution
status. Possible nodal/media failure or misconfiguration. Diagnose
path resolution failure. Submit an SR if necessary. |
MESSAGE: None | CAUSE: PATHs failed
to resolve a path to the requested destination. The passive connection
attempt has failed. ACTION: PARM is path resolution
status. Possible nodal/media failure or misconfiguration. Diagnose
path resolution failure. Submit an SR if necessary. |
MESSAGE: None | CAUSE: The Path
reply came back with a bad status. We can't get a route
to establish connection. ACTION: PARM is path reply
error returned. Possible nodal/media failure or misconfiguration.
Diagnose path resolution failure. Submit an SR if necessary. |
MESSAGE: None | CAUSE: We have
received numerous consecutive path replies, but we still haven't
received a good route to establish the connection. We assume that
the path resolution mechanism has entered a sick state for this
route and is unable to resolve our destination. ACTION: Possible nodal/media
failure or misconfiguration. Diagnose path resolution failure. Submit
an SR if necessary. |
MESSAGE: None | CAUSE: The TCP
SIP couldn't get a route to send an outbound reset. ACTION: Informative message.
No action required. Try to determine why route to remote host has
failed. Possibilities include node/media failure and misconfiguration. |
MESSAGE: None | CAUSE: The TCP
SIP couldn't get a route to send an outbound reset after
waiting for reply from paths. ACTION: Informative message.
No action required. Try to determine why route to remote host has
failed. Possibilities include node/media failure and misconfiguration. |
MESSAGE: None | CAUSE: We verified
a connection's route due to negative advice, and found
that there is no longer a route to the remote host. The connection
will abort. ACTION: Informative message.
No action required. Try to determine why route to remote host has
failed. Possibilities include node/media failure and misconfiguration. |
MESSAGE: None | CAUSE: Nettmr_reset_timer
call returned an error. ACTION: PARM is nettmr
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Nettmr_free_timer
call returned an error. ACTION: PARM is nettmr
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Nettmr_get_timer
call returned an error. ACTION: PARM is nettmr
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Nettmr_reset_timer
call returned an error. ACTION: PARM is nettmr
error returned. Submit an SR. |
MESSAGE: None | CAUSE: CB_INIT
returned a bad status while initializing the hash table semaphore.
CB_INIT was called during network
startup. ACTION: PARM is semaphores
error returned. Submit an SR. |
MESSAGE: None | CAUSE: CB_INIT
returned a bad status while initializing the global TCP semaphore.
CB_INIT was called during network
startup. ACTION: PARM is semaphores
error returned. Submit an SR. |
MESSAGE: None | CAUSE: CB_INIT
returned a bad status while initializing a connection semaphore.
CB_INIT was called during TCP connection
establishment. ACTION: PARM is semaphores
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Attempt
to unfreeze user data vector failed. ACTION: PARM is memory manager
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Attempt
to freeze user data vector failed. ACTION: PARM is memory manager
error returned. Submit an SR. |
MESSAGE: None | CAUSE: Attempt
to unfreeze user data vector failed. ACTION: PARM is memory manager
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NMCLOSETRACE
returned a bad status during an IPCCONTROL
traceoff call. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMOPENLOG
returned a bad status during network startup. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMMONSTARTREQ
call returned a bad status during network startup. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
was returned in a message from the TCP SIP during network startup.
The TCP SIP initialization has failed. ACTION: PARM is TCP SIP initialization
error. Look for a logging indication explaining TCP SIP initialization
failure. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
was returned from NMCLOSELOG. This
was called during system shutdown. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
was returned from NMMONDELETEID.
This was called during system shutdown. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: Bad status
was returned from NMCLOSELOG during
network shutdown. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMWRITETRACE call
returned a bad status while tracing a data packet ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMWRITETRACE call
returned a bad status while tracing a reset packet being sent out
by the TCP SIP. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMWRITETRACE
call returned a bad status while tracing an ICMP message. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMWRITETRACE call
returned a bad status while tracing a resource interface. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NMWRITETRACE
call returned a bad status while tracing a resource interface. ACTION: PARM is the NMS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: REG_DEL_ENTITY
returned a bad status. It was called during network shutdown. ACTION: PARM is the registry
error returned. Submit an SR. |
MESSAGE: None | CAUSE: REG_ADD_ENTITY
returned a bad status. It was called during network startup. ACTION: PARM is the registry
error returned. Submit an SR. |
MESSAGE: None | CAUSE: NWWRITETRACE
returned a bad status while attempting to write a state trace record
for a connection. ACTION: PARM is NWS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NWWRITETRACE
returned a bad status while attempting to write a state trace record
for the TCP SIP. ACTION: PARM is NWS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NWWRITETRACE
returned a bad status while attempting to write a message or procedure
call trace record for a connection. ACTION: PARM is NWS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: NWWRITETRACE
returned a bad status while attempting to write a message or procedure
call trace record for the TCP SIP. ACTION: PARM is NWS error
returned. Submit an SR. |
MESSAGE: None | CAUSE: DICT_DELETE
returned a bad status while attempting to remove the TCP SIP from
the cm port dictionary during shutdown. ACTION: PARM is the returned
error. Submit an SR. |
MESSAGE: None | CAUSE: A call
to an SDI driver failed. ACTION: PARM is the call
result status. Submit an SR. |
MESSAGE: None | CAUSE: TCP accepted
a new ack, but no outstanding data
was found on the retransmission queue. The connection is in an inconsistent
state. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: HPGETSYSPLABEL
call failed to get plabel of TCP's timer trap routine.
This would occur during network startup. ACTION: Network Transport
installation looks suspicious. Verify Transport installed correctly.
Submit an SR. |
MESSAGE: None | CAUSE: TCP received
a packet in the syn_received state,
but found that the internal IPC state was not consistent with this
state. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: TCP received
a packet in the syn_sent state,
but found that the internal IPC state was not consistent with this
state. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: TCP has
entered a state (processing an inbound fin) which inconsistent with
its internal IPC state. This is a software error. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: TCP internal
timer state was inconsistent with actual timer activity. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: TCP wanted
to adjust the length of data of a composite buffer beyond the end
of the last buffer in the chain. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from a call to the tcp_read_completor
in the loopback send path. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned from a call to the tcp_read_completor
in the loopback retransmissive send path. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: We received
a reply from buffer manager containing a buffer that is not part
of our buffer pool. ACTION: Informative message.
No action required. This may indicate a procedural error within
TCP. |
MESSAGE: None | CAUSE: We received
a reply from buffer manager when we weren't expecting one.This
is a software error in TCP. ACTION: This is a dangerous
circumstance, as we are not keeping proper track of our resources.
Submit an SR. |
MESSAGE: None | CAUSE: We received
a reply from buffer manager but our buffer state indicated that
we were not expecting one. ACTION: This is a dangerous
circumstance, as we are not keeping proper track of our resources.
Submit an SR. |
MESSAGE: None | CAUSE: We had
a problem resegmenting the retransmission queue. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Attempt
to add a network to TCP's IP list table when the table
is full. Connection is added to temporary list. ACTION: PARM is source IP
address of connection. Check configuration for number of configured
networks. If ok, then submit an SR. |
MESSAGE: None | CAUSE: Connection
could not be found in TCP's IP list table when it is shutting
down. ACTION: PARM is source IP
address of connection. Submit an SR. |
MESSAGE: None | CAUSE: Connection
was removed from TCP's temporary IP list table. See location
11901. ACTION: PARM is source IP
address of connection. Check configuration for number of configured
networks. If ok, then submit an SR. |
MESSAGE: None | CAUSE: A connection
received a packet with a bad checksum. ACTION: Informative message.
No action required. Bad checksums usually indicate poor transmission
quality. |
MESSAGE: None | CAUSE: A connection
received a packet with a bad checksum. ACTION: Informative message.
No action required. Bad checksums usually indicate poor transmission
quality. |
MESSAGE: None | CAUSE: A connection
received a packet with a bad checksum. ACTION: Informative message.
No action required. Bad checksums usually indicate poor transmission
quality. |
MESSAGE: None | CAUSE: The TCP
SIP tossed an inbound packet due to a bad checksum. ACTION: Informative message.
No action required. Bad checksums usually indicate poor transmission
quality. |
MESSAGE: None | CAUSE: A TCP connection
received a packet with precedence or security options which do not
match those of the connection. The connection will abort. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
If precedence or security option of inbound packet changes report
an error against the remote implementation. Otherwise, submit an
SR. |
MESSAGE: None | CAUSE: A TCP connection
received a packet with precedence or security options which do not
match those of the connection. The connection will abort. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
If precedence or security option of inbound packet changes report
an error against the remote implementation. Otherwise, submit an
SR. |
MESSAGE: None | CAUSE: A TCP connection
received a packet with precedence or security options which do not
match those of the connection. The connection will abort. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
If precedence or security option of inbound packet changes report
an error against the remote implementation. Otherwise, submit an
SR. |
MESSAGE: None | CAUSE: The TCP
SIP tossed an inbound packet due to unmatched precedence or security
to the intended socket. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: A packet
was received by a connection which had the syn
flag set and was within window. This is a remote protocol violation.
The connection will abort. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
Report an error against remote implementation. |
MESSAGE: None | CAUSE: A packet
was received by a connection which had the syn
flag set and was within window. This is a remote protocol violation.
The connection will abort. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
Report an error against remote implementation. |
MESSAGE: None | CAUSE: A packet
was received without the ACK flag set by a connection in a state
in which such a packet is not acceptable. The packet will be ignored.
This is a remote protocol violation. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
Report an error against remote implementation. |
MESSAGE: None | CAUSE: A packet
was received without the ACK flag set by a connection in a state
in which such a packet is not acceptable. The packet will be ignored.
This is a remote protocol violation. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
Report an error against remote implementation. |
MESSAGE: None | CAUSE: A packet
was received without the ACK flag set by a connection in a state
in which such a packet is not acceptable. The packet will be ignored.
This is a remote protocol violation. ACTION: Remote protocol error
indication. Use tracing or line analysis to capture connection dialog.
Report an error against remote implementation. |
MESSAGE: None | CAUSE: A packet
was received with an invalid ACK status. The packet will be ignored. ACTION: Remote protocol error
indication. Occasional occurrences are acceptable. Excessive occurrences
indicate an error with either the remote or local connection half's
tracking of current sequence number statuses. Submit an SR; report
an error against the remote implementation. |
MESSAGE: None | CAUSE: A packet
was received with an invalid ACK status. The packet will be ignored. ACTION: Remote protocol error
indication. Occasional occurrences are acceptable. Excessive occurrences
indicate an error with either the remote or local connection half's
tracking of current sequence number statuses. Submit an SR; report
an error against the remote implementation. |
MESSAGE: None | CAUSE: A packet
was received with an invalid ACK status. The packet will be ignored. ACTION: Remote protocol error
indication. Occasional occurrences are acceptable. Excessive occurrences
indicate an error with either the remote or local connection half's
tracking of current sequence number statuses. Submit an SR; report
an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: The remote
connection half has sent data with a sequence number which exceeds
the fin sequence number which the remote sent previously. This is
a remote protocol violation. ACTION: Capture data traffic
including offending fin and following data packet using tracing
or a line analyzer. Report an error against the remote implementation. |
MESSAGE: None | CAUSE: A packet
was received which contained a TCP header with a max tpdu
option which had an incorrect option length in the option length
field. ACTION: Capture data traffic
including offending data packet using tracing or a line analyzer.
Report an error against the remote implementation. |
MESSAGE: None | CAUSE: TCP SIP
sent out a reset for a packet with the ack
flag set that was received on a socket in listen state. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: TCP SIP
tossed a packet with the ack and
syn flags set that was received
for a socket in the listen state. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: Inbound
packet received for a closed (not opened) sap, so the TCP SIP will
send a reset. ACTION: Informative message.
No action required. Start service or open correct SAP if necessary.
PARM is SAP for which packet is bound. |
MESSAGE: None | CAUSE: IPC called tcp_receive_reply,
but TCP did not have any record of data outstanding to IPC. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: IPC called
tcp_receive_reply, but TCP data
indicates that IPC should not be in data receptive state. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: An attempt
was made to start a TCP connection; however, the protocol was not
active (i.e., was stopped). ACTION: Informative message.
Start the network if needed. |
MESSAGE: None | CAUSE: An attempt
was made to open a TCP socket; however, the protocol was not active
(i.e., was stopped). ACTION: Informative message.
Start the network if needed. |
MESSAGE: None | CAUSE: We received
an inbound syn packet we will not
process because the transport is not up. ACTION: Informative message.
Start the transport if needed. |
MESSAGE: None | CAUSE: The value
in the KSO table for the TCP SIP data structure is nil when TCP_MODULE_DECONFIG
is called. ACTION: Look for startup
errors. Submit an SR. |
MESSAGE: None | CAUSE: An attempt
to create a TCP socket was made before the transport had been started. ACTION: Informative message.
Start the transport if needed. |
MESSAGE: None | CAUSE: An attempt
to listen on a TCP socket was made before the transport had been
started. ACTION: Informative message.
Start the transport if needed. |
MESSAGE: None | CAUSE: An attempt
to shut down a TCP socket was made before the transport had been
started. ACTION: Informative message.
Start the transport if needed. |
MESSAGE: None | CAUSE: An attempt
to establish a TCP connection was made before the transport had
been started. ACTION: Informative message.
Start the transport if needed. |
MESSAGE: None | CAUSE: User passed
bad TCP control parameter through IPCCONTROL. ACTION: PARM is value of
offending control parameter. Fix offending program/service. |
MESSAGE: None | CAUSE: Number
of configured retransmission retries exceeded. Connection will abort. ACTION: Excessive retransmissions
indicate a possible route/gate failure or possible end node failure
or possible misconfiguration. Extreme network bottlenecks may also
cause this type of problem although TCP should be able to adjust
to most network conditions. A temporary work around may be to increase
the configured number of maximum retransmissions. If a direct cause
is not found consider further diagnosis with a line analyzer or
submitting an SR. |
MESSAGE: None | CAUSE: The total
retransmission time for a packet has exceeded the configured MAXIMUM
TIME TO WAIT FOR REMOTE RESPONSE. Connection will abort. ACTION: Excessive retransmission
time indicates a possible route/gate/end node failure or possible
misconfiguration. Extreme network bottlenecks may also cause this
type of problem although TCP should be able to adjust to most network
conditions. A temporary work around may be to increase the MAXIMUM
TIME TO WAIT FOR REMOTE RESPONSE. If a direct cause is not found
consider further diagnosis with a line analyzer or submitting an
SR. |
MESSAGE: None | CAUSE: A valid
reset packet was received on a connection. The connection will abort. ACTION: Informative message.
No action required. This message normally appears because the remote
connection half was terminated abruptly by the user through an abortive
IPC shutdown. Many services use this type of shutdown. Remote abortions
also occur when errors are encountered on the remote system. In
unexpected abortion situations inspection of the remote system for
indications of error is suggested. |
MESSAGE: None | CAUSE: A valid
reset packet was received on a connection. The connection will abort. ACTION: Informative message.
No action required. This message normally appears because the remote
connection half was terminated abruptly by the user through an abortive
IPC shutdown. Many services use this type of shutdown. Remote abortions
also occur when errors are encountered on the remote system. In
unexpected abortion situations inspection of the remote system for
indications of error is suggested. |
MESSAGE: None | CAUSE: A valid
reset packet was received on a connection. The connection will abort. ACTION: Informative message.
No action required. This message normally appears because the remote
connection half was terminated abruptly by the user through an abortive
IPC shutdown. Many services use this type of shutdown. Remote abortions
also occur when errors are encountered on the remote system. In
unexpected abortion situations inspection of the remote system for
indications of error is suggested. |
MESSAGE: None | CAUSE: Connection
Assurance timeout occurred for this connection. The remote node
did not respond within the configured number of CA retries. ACTION: Suspect remote node
failure, or possible network failure. |
MESSAGE: None | CAUSE: BMGR_CREATE_POOL
returned a bad status while trying to create the TCP control buffer
pool. This would occur during network startup. ACTION: PARM is BMGR error
returned. Submit an SR. |
MESSAGE: None | CAUSE: BMGR_DELETE_POOL
returned a bad status while trying to delete the TCP control buffer
pool. ACTION: PARM is BMGR error
returned. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_process_inbound
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_read_completor
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_active_open
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_active_open
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_passive_open_reply
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_connection_shutdown
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_connection_shutdown
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_control
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_listen
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_socket_shutdown
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_create_socket
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_send
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_receive_reply or
some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_is_inbound_urgent
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_module_config
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_main_loop
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure decipher_msg
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure decipher_ds_msg
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure decipher_ds_msg
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_process_inbound or
some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_negative_advice
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_icmp_req
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_traceon
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_traceoff
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_net_stop
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_sip_route_valid
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_path_reply
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_pm_buffer_reply
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_passive_open
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_module_deconfig
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_driver_down
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_flush_sends
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_get_option
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: An unexpected
escape occurred within the procedure tcp_set_option
or some procedural unit called by it. ACTION: PARM is escape code
of escape. Submit an SR. |
MESSAGE: None | CAUSE: A TCP connection
tossed a packet because it contained data which only duplicated
data already received. This usually indicates an inbound retransmission
for which the original has already been received. ACTION: Informative message.
No action required. Excessive retransmissions indicate either a
faulty sending implementation or a noisy line. |
MESSAGE: None | CAUSE: A connection
tossed a packet because of an invalid sequence number. May be caused
by inbound retransmissions, connection assurance packets, or window
probes. ACTION: Informative message.
No action required. Occasional occurrences normal. Excessive occurrences
indicate abnormal software operation. |
MESSAGE: None | CAUSE: A connection
tossed a packet because of an invalid sequence number. May be caused
by inbound retransmissions, connection assurance packets, or window
probes. ACTION: Informative message.
No action required. Occasional occurrences normal. Excessive occurrences
indicate abnormal software operation. |
MESSAGE: None | CAUSE: A connection
tossed a packet because of an invalid sequence number. May be caused
by inbound retransmissions, connection assurance packets, or window
probes. ACTION: Informative message.
No action required. Occasional occurrences normal. Excessive occurrences
indicate abnormal software operation. |
MESSAGE: None | CAUSE: A connection
tossed a packet because of an invalid sequence number. May be caused
by inbound retransmissions, connection assurance packets, or window
probes. ACTION: Informative message.
No action required. Occasional occurrences normal. Excessive occurrences
indicate abnormal software operation. |
MESSAGE: None | CAUSE: A connection
tossed a packet because of an invalid sequence number. May be caused
by inbound retransmissions, connection assurance packets, or window
probes. ACTION: Informative message.
No action required. Occasional occurrences normal. Excessive occurrences
indicate abnormal software operation. |
MESSAGE: None | CAUSE: A packet
was tossed because the connection it was destined for is no longer
active. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: A TCP connection
tossed a packet because it contained only out of window data. This
may indicate strange behavior on the part of the sender or confusion
on the part of the receiver. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet from a half open connection because the TCP
SIP was already processing another such packet. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet from a half open connection because the TCP
SIP was already processing another such packet. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet from a half open connection because it couldn't
get a route to send an outbound reset. ACTION: Informative message.
No action required. Possibly diagnose route resolution failure.
Likely link/gate/nodal failure or configuration error. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet from a half open connection because it couldn't
get a route, after waiting for a reply from paths, to send an outbound
reset. ACTION: Informative message.
No action required. Possibly diagnose route resolution failure.
Likely link/gate/nodal failure or configuration error. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet from a half open connection because it had the
reset flag set. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The TCP
SIP tossed a packet because it had the reset flag set and destination
socket was in the listen state. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The retransmission
interval for a packet has expired; however, a previous transmission
of this packet has not yet left the node (or in loopback has not
been released by the receiver). ACTION: This indicates congestion
within the node itself (e.g. the host running faster than the card
can allow). Occasional occurrences are considered normal. Excessive
occurrences (in other than loopback) indicate a more serious software
problem. |
MESSAGE: None | CAUSE: An attempt
was made to retransmit a packet in loopback. ACTION: Repeated occurrences
indicated a software problem. |
MESSAGE: None | CAUSE: The retransmission
interval for a packet has expired without receipt of an acknowledgment
from the remote connection half. ACTION: This indicates network
congestion, or a noisy or loss prone network. Occasional occurrences
are considered normal. Excessive occurrences resulting in connection
disconnects may indicate nodal/media failure, misconfiguration,
severe network bottlenecks, or software failure. |
MESSAGE: None | CAUSE: An excessive
number of retransmissions has caused a negative advice indication
has been sent to the TCP SIP. The SIP will verify that our route
to our destination is still correct. ACTION: Informative message.
No action required. This logging indicates that TCP has proactively
detected potential route/link/gate/ring failure. If route validation
fails and no new route to the remote host is found, diagnose route
failure. Possibilities include node/media failure and misconfiguration. |
MESSAGE: None | CAUSE: A timer
popped after it had already been released. ACTION: Informative message.
No action required. Occasional occurrences are normal. Excessive
occurrences indicate the possibility of a software error. |
MESSAGE: None | CAUSE: An ICMP
source quench packet has been processed for this TCP connection.
The connection will treat the event as a Van Jacobson retransmission
event. ACTION: Informative message.
No action required. Source quench indicates that some gateway in
the path (or the receiving node) is running low on buffer space.
Possibly increase gateway store and forward buffer pool size or
receiving node's buffer pool size if configurable. |
MESSAGE: None | CAUSE: The user
attempted to open a connection which already exists. ACTION: User error. Isolate
and correct offending program or service. Submit an SR if necessary. |
MESSAGE: None | CAUSE: We received
an inbound syn for a connection
that has already been established (same local and destination SAPS
and IP addresses). We will ignore this SYN packet. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: The user
or service (through IPC) has rejected the passive connection attempt,
or an error has occurred on the connection since the passive open
request was received. ACTION: Informative message.
PARM is rejection reason. If PARM is 0, user/service rejected the
connection. Otherwise, an error condition has been detected by TCP.
Look for logging indication of other error on same connection. (Remember
that other logging classes may or may not be enabled.) Network/nodal
shutdown processing may cause this error. If error is unexplainable,
submit an SR. |
MESSAGE: None | CAUSE: TCP connection
deactivated due to an error. ACTION: Informative message.
No action required. Error type may be normal or serious. Find matching
error indication for connection and follow action text. (Remember
that all classes of logging may not be enabled.) |
MESSAGE: None | CAUSE: User or
service attempted to create TCP socket which already exists. ACTION: Correct program/service
in error or close previous socket incarnation. |
MESSAGE: None | CAUSE: TCP protocol
start failed. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Bad status
returned in message from TCP SIP during a network startup. The TCP
SIP wasn't created. ACTION: PARM indicates status
from message. Look for logging indication explaining TCP SIP initialization
failure. Submit an SR. |
MESSAGE: None | CAUSE: TCP SIP
portid was not found. ACTION: Suspect error in
protocol startup or protocol initialization. Look for logging indication
explaining TCP SIP initialization failure. Submit an SR. |
MESSAGE: None | CAUSE: Error in
protocol initialization. ACTION: Look for logging
indication explaining TCP SIP initialization failure. Submit an
SR. |
MESSAGE: None | CAUSE: TCP KSO
pointer value was NIL. ACTION: Suspect error in
protocol startup. Look for logging indication explaining TCP protocol
startup failure. Submit an SR. |
MESSAGE: None | CAUSE: Bad port
message of 'DS' type came to the
TCP SIP. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Bad port
message of unknown type came to the TCP SIP. ACTION: Submit an SR. |
MESSAGE: None | CAUSE: Inbound
syn packet will not be processed
because we will go over the TCP maximum connection limit if we do. ACTION: Informative message.
No action required. Increase configured TCP connection maximum if
required and restart network. |
MESSAGE: None | CAUSE: The program
TCPSIP.NET.SYS was invoked by a
father process other than NMMON. The program will exit gracefully. ACTION: Informative message.
No action required. |
MESSAGE: None | CAUSE: An attempt
was made to open more sockets than the maximum allowed on the system. ACTION: Informative message.
The maximum allowed sockets varies directly with the configured
number of connections. Increase the configured number of connections
and restart the network. |
MESSAGE: None | CAUSE: TCP connection
(PM) activated. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: Graceful
connection shutdown complete. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP connection
deactivated without error. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP socket
opened. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP socket
closed. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP protocol
started. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: The TCP
SIP has been started. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP protocol
stopped. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP SIP
process stopped. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP SIP
process stopped. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: TCP protocol
stopped. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: Network
shut message processed for parm> ip_addr. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: Asynchronous
driver error occurred for parm> ip_addr. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: Path_verify
message from NETCP processed for parm> ip_addr. ACTION: Informational message.
No action required. |
MESSAGE: None | CAUSE: The global
TCP statistics are being recorded. ACTION: Statistical message.
No action required. |
MESSAGE: None | CAUSE: Specific
statistics related to the efficiency of the hash table are being
recorded. ACTION: Statistical message.
No action required. |
MESSAGE: None | CAUSE: A TCP connection
is shutting down and recording its statistics. ACTION: Statistical message.
No action required. |
|