(S/R)

(RE)STORE ENCOUNTERED EXCESSIVE REWIND ERRORS ON LDEV !

Bad media or drive problem caused too many errors.

Physically dismount bad media and mount new one.

READY TO TRY REWIND FOR (RE)STORE on LDEV ! (Y/N)

Too many rewind errors on previous try.

Mount good media and reply to console query.

STORE/RESTORE ENCOUNTERED UNKNOWN MEDIA ON LDEV !

Media type is incompatible with store subsystem.

Mount compatible media type or update store.

LABEL READ FAIL ON LDEV !. USE ANYWAY?(Y/N)

Media read error while trying to read media label.

Check paper label on media and reply to the console query.

LABEL READ FAIL ON LDEV ! FOR MEDIA !. USE IT?(Y/N)

Media read error on label read with (re)storeset option.

Check paper label on media and reply to console query.

LABEL READ FAIL ON LDEV ! FOR MEDIA !. USE IT?(Y/N)

Media read error on label read with (re)storeset option.

Check the paper label and reply to the console query.

MOUNT NEXT MEDIA FOR RESTORE ON LDEV !

Restore finished the current mounted media.

Mount next media to be restored.

MOUNT MEDIA ! FOR RESTORE ON LDEV !

Restore with restoreset option finished the currently mounted media.

Mount next media on specified ldev.

MOUNT MEDIA ! OF SET ! FOR RESTORE ON LDEV !

Restore with restoreset finished a media from parallal set store.

Mount next media of the specified set on requesting ldev.

DISMOUNT CURRENT MEDIA FOR RESTORE ON LDEV !

A wrong media was mounted for restore on specified ldev.

Dismount wrong media and mount a correct one.

DISMOUNT MEDIA ! FOR RESTORE ON LDEV !

An out of order media was mounted.

Dismount this media and mount a correct one.

DISMOUNT MEDIA ! OF SET ! FOR RESTORE ON LDEV !

An out of order media was mounted for restore.

Dismount wrong media and mount the correct one.

MEDIA LEADER TOO SHORT. DISMOUNT CURRENT MEDIA ON LDEV !

Media error encountered due to insufficient media leader.

Mount media with long enough media leader.

MEDIA ON LDEV ! IS NOT A STORE MEDIA

A non-store media is mounted for restore.

Only store media can be read by NM restore.

MEDIA ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA

An out of order media was mounted for restore.

Dismount this media and mount the correct one.

MEDIA ! ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA

An out of order media was mounted for restore with restoreset option.

Dismount this media and mount the correct one.

MEDIA ! OF SET ! ON LDEV ! IS PREVIOUS TO REQUESTED MEDIA

An out of order media from a parallel storeset was mounted for restore.

Dismount this media and mount the correct one.

INCORRECT MEDIA DISMOUNTED BY RESTORE ON LDEV !

An incorrect media was placed offline by restore.

Unload this media and mount the correct one.

MEDIA ON LDEV ! IS NOT FROM THIS STORE SET

The mounted media is not from the set being restored on this ldev.

Dismount the incorrect media and mount the correct one.

MEDIA ON LDEV ! WAS MOUNTED BUT NEVER WRITTEN

Although the media on the specified ldev was mounted (most likely for a serial store), no data was written to it.

Do not include this media as part of the backup, since it contains no data.

MEDIA ON LDEV ! WAS NOT REQUESTED. USE IT? (Y/N)

Media later than requested was mounted on ldev.

Reply Y if you want to skip media otherwise reply n and mount correct media.

MEDIA ! ON LDEV ! WAS NOT REQUESTED. USE IT? (Y/N)

Media later than requested was mounted along with restoreset option.

Reply Y if want to skip media or else reply N and mount the correct media.

MEDIA ! OF SET ! ON LDEV ! IS WRONG. USE IT? (Y/N)

Media from later set than requested was mounted.

Reply Y if want to skip media else reply y and mount correct media.

MOUNT NEXT MEDIA FOR STORE ON LDEV !

Store finished writing the current media .

Unload current media and mount a new one.

MOUNT MEDIA ! FOR STORE ON LDEV !

Store with storeset option finished writing a media.

Unload the current media and mount a new one.

MOUNT MEDIA ! OF SET ! FOR STORE ON LDEV !

Store with storeset option finished writing a media.

Unload the current media and mount a new one.

STORE IS STARTING TO WRITE NEXT MEDIA ON LDEV !

Store accepted the newly mounted media.

None.

STORE IS STARTING TO WRITE MEDIA ! ON LDEV !

Store with storeset option accepted the newly mounted media.

None.

STORE IS STARTING TO WRITE MEDIA ! OF SET ! ON LDEV !

Store with storeset option accepted the newly mounted media.

None.

MEDIA ON LDEV ! IS PART OF CURRENT STORE SET

Media of the current store command was remounted to be overwritten.

Save this media and mount a blank one instead.

MEDIA ! ON LDEV ! IS PART OF CURRENT STORE SET

Media from current store with storeset option was mounted to be overwritten.

Save this media and mount a blank one.

MEDIA ! OF SET ! ON LDEV ! IS PART OF CURRENT STORE SET

Media of current store with storeset option was mounted to be overwritten.

Save this media and mount a blank one.

MEDIA ON LDEV ! IS BAD. CONTINUE ANYWAY?(Y/N)

The media just mounted gave write errors at some time before this.

Reply Y if you want to retry the media or else reply N and mount a good media.

STORE IS MARKING MEDIA BAD ON LDEV !

Store came accross a write error on this media.

Dismount this media and mount a good one.

STORE IS MARKING MEDIA ! BAD ON LDEV !

Store with storeset option had a write error on specified ldev.

Dismount bad media and mount a good one.

STORE IS MARKING MEDIA ! OF SET ! BAD ON LDEV !

Store with storeset option had a write error on the specified ldev.

Dismount bad media and mount a good one.

RESTORE IS ASSUMING THAT NEXT MEDIA IS ON LDEV !

Media was mounted on ldev out of sequence with restoreset order.

None.

RESTORE IS ASSUMING THAT MEDIA ! IS ON LDEV !

Media was mounted on an ldev out of sequence from restoreset order.

None.

RESTORE IS ASSUMING THAT MEDIA ! OF SET ! IS ON LDEV !

Media was mounted on ldev out of sequence with the restoreset option order.

None.

USE DAMAGED TAPE AS NEXT MEDIA ON LDEV !(Y/N)

The media directory on this media was damaged.

Reply Y if this indeed is the correct media or else reply N and mount the correct one.

USE DAMAGED TAPE AS MEDIA ! ON LDEV !(Y/N)

The media directory on this media was found to be damaged.

Reply Y to console query if this indeed is the correct media or else reply N.

USE DAMAGED TAPE AS MEDIA ! OF SET ! ON LDEV !(Y/N)

The media directory on this media was damaged.

Reply Y to the console query if this indeed is the correct media or else reply N.

FILES LOCKED BY ONLINE STORE ARE NOW FREE FOR READ/WRITE/PURGE

The files specified for an online store have been attached to the logging mechanism.

These files may now been opened for read or write access, or may be purged.

THE MEDIA ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE

The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this media and mount a piece of media that does not belong to an already allocated restoreset.

MEDIA ! ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE

The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this tape and mount a piece of media that does not belong to an already allocated restoreset.

MEDIA ! OF SET ! ON LDEV ! IS ALLOCATED TO SOME OTHER DRIVE

The media that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this tape and mount a piece of media that does not belong to an already allocated restoreset.

FILES OF STORE SET ! WILL BE RESTORED WHEN A DRIVE BECOMES FREE

There are more parallel restoresets to restore than there are devices, so the specified set will be restored once a backup device becomes available.

Information only. When a drive becomes free, this set can be mounted and restored.

STARTING TO RESTORE THE FILES OF STORE SET ! ON LDEV !

The files of the specified store set are now being restored from the specified ldev.

Information only.

LDEV ! SPECIFIED IN THE RESTORESET OPTION IS RELEASED

There are no files to restore from this device, so it is being closed.

Information only.

LABELED VOLUME MOUNTED FOR UNLABELED STORE ON LDEV !.

Labeled volumes can not be used for unlabeled stores.

Dismount this volume and mount an unlabeled media.

DISMOUNT VOLUME OF VOLSET ! FOR RESTORE ON LDEV !

The specified labeled volume is no longer needed by restore.

Dismount the volume from the specified ldev.

DISMOUNT MEDIA ! OF VOLSET ! FOR RESTORE ON LDEV !

The specifieid lableled volume is no longer needed by restore.

Dismount the volume from the specified ldev.

DISMOUNT VOL ! OF VOLSET ! FOR RESTORE ON LDEV !

The specifieid lableled volume is no longer needed by restore.

Dismount the volume from the specified ldev.

FILES OF VOLSET ! WILL BE RESTORED WHEN A DRIVE BECOMES FREE

There are more parallel restoresets to restore than there are devices, so the specified volume set will be restored once a backup device becomes available.

Information only. When a drive becomes free, this set can be mounted and restored.

STARTING TO RESTORE FILES OF VOLSET ! ON LDEV !

The files of the specified volume set are now being restored from the specified ldev.

Information only.

RESTORE ASSUMES THAT NEXT VOL OF VOLSET ! IS ON LDEV !

Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.

Information only.

RESTORE ASSUMES THAT MEDIA ! OF VOLSET ! IS ON LDEV !

Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.

Information only.

RESTORE ASSUMES THAT VOL ! OF VOLSET ! IS ON LDEV !

Even though an error was encountered while reading the label of this volume, the user has instructed that it be used anyway, and restore assumes it is the specified volume.

Information only.

USE DAMAGED MEDIA AS NEXT VOLUME OF SET ! ON LDEV ! (Y/N)

An error was encountered while reading the label of this volume.

Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.

USE DAMAGED MEDIA AS MEDIA ! OF SET ! ON LDEV !(Y/N)

An error was encountered while reading the label of this volume.

Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.

USE DAMAGED MEDIA AS VOL ! OF SET ! ON LDEV !(Y/N)

An error was encountered while reading the label of this volume.

Reply Yes to the console request if this volume should be used anyway. Reply No to cause this volume to be dismounted.

MOUNT NEXT MEMBER OF VOLSET ! FOR RESTORE ON LDEV !

Restore needs the next member of the specified volume set.

Find and mount the next member of the specified volume set on the specified ldev.

MOUNT MEDIA ! OF VOLSET ! FOR RESTORE ON LDEV !

Restore needs a specific member of the specified volume set.

Find and mount the requested media on the specified ldev.

MOUNT VOL ! OF VOLSET ! FOR RESTORE ON LDEV !

Restore needs a specific volume from a specific volume set.

Find and mount the requested volume on the specified ldev.

VOLUME OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)

An unexpected labeled volume was mounted for restore.

Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.

MEDIA ! OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)

An unexpected labeled volume was mounted for restore.

Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.

VOL ! OF SET ! ON LDEV ! INCORRECT. USE IT? (Y/N)

An unexpected labeled volume was mounted for restore.

Reply Yes to the console message to have restore use this volume. All files that were on unmounted volumes previous to this one will not be restore. Reply No to cause this volume to be dismounted.

MEMBER OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA

A non-store labeled volume was mounted for restore.

Only store media can be read by NM Restore.

MEDIA ! OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA

A non-store labeled volume was mounted for restore.

Only store media can be read by NM Restore.

VOL ! OF VOLSET ! ON LDEV ! IS NOT A STORE MEDIA

A non-store labeled volume was mounted for restore.

Only store media can be read by NM Restore.

VOLUME OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE

The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this volume and mount a volume that does not belong to an already allocated restoreset.

MEDIA ! OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE

The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this volume and mount a volume that does not belong to an already allocated restoreset.

VOL ! OF VOLSET ! ON LDEV ! IS ALLOCATED TO ANOTHER DRIVE

The volume that has been mounted belongs to a parallel restoreset that is already being restored on another device.

Dismount this volume and mount a volume that does not belong to an already allocated restoreset.

VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !

The wrong labeled volume has been mounted for this restore.

This volume is being dismounted. The next console message will specify which volume should be mounted.

VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !

The wrong labeled volume has been mounted for this restore.

This volume is being dismounted. The next console message will specify which volume should be mounted.

VOLUME NOT MEMBER OF VOLSET ! ; DISMOUNTED BY RESTORE ON LDEV !

The wrong labeled volume has been mounted for this restore.

This volume is being dismounted. The next console message will specify which volume should be mounted.

MEMBER OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED

A volume which has already be restored from, or which is no longer needed, has been mounted.

Dismount this volume and mount the previously requested volume.

MEDIA ! OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED

A volume which has already be restored from, or which is no longer needed, has been mounted.

Dismount this volume and mount the previously requested volume.

VOL ! OF VOLSET ! ON LDEV ! IS PRIOR TO THAT REQUESTED

A volume which has already be restored from, or which is no longer needed, has been mounted.

Dismount this volume and mount the previously requested volume.

VOL ID GIVEN FOR MEMBER OF VOLSET ! ON LDEV ! IS INVALID

The volume id of this volume is incorrect.

Dismount this volume and mount a volume from the specified volume set.

LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !

Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.

Mount a type-compatible labeled volume.

LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !

Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.

Mount a type-compatible labeled volume.

LABEL TYPE CLASH BETWEEN VOLSET ! AND VOLUME ON LDEV !

Either an ANSI labeled volume was mounted when an IBM label was expected, or vice versa.

Mount a type-compatible labeled volume.

REPLY WITH VOL ID FOR MEMBER OF VOLSET !

A new labeled volume needs a volume id.

Reply to the console message with the new volume id for this volume.

REPLY WITH VOL ID FOR MEDIA ! OF VOLSET !

A new labeled volume needs a volume id.

Reply to the console message with the new volume id for this volume.

VOLUME OF VOLSET ! ON LDEV ! IS BEING MARKED BAD

A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.

After store has marked this volume bad, dismount it and mount a new volume.

MEDIA ! OF VOLSET ! ON LDEV ! IS BEING MARKED BAD

A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.

After store has marked this volume bad, dismount it and mount a new volume.

VOL ! OF VOLSET ! ON LDEV ! IS BEING MARKED BAD

A media error occurred while writing to this volume. The volume will be marked bad to indicate there was an error while writing to it.

After store has marked this volume bad, dismount it and mount a new volume.

MOUNT NEXT MEMBER FOR VOLSET ! FOR STORE ON LDEV !

Store has finished writing to the current volume and needs the next volume.

Dismount the current volume and mount the next volume for the volume set on the specified ldev.

MOUNT MEDIA ! FOR VOLSET ! FOR STORE ON LDEV !

Store has finished writing to the current volume and needs the next volume.

Dismount the current volume and mount the next media for the volume set on the specified ldev.

MOUNT VOL ! FOR VOLSET ! FOR STORE ON LDEV !

Store has finished writing to the current volume and needs the next volume.

Dismount the current volume and mount the specified volume for the volume set on the specified ldev.

STARTING TO WRITE TO MEMBER OF VOLSET ! ON LDEV !

Store is being to write to a member of the specified volume set.

Information only.

STARTING TO WRITE TO MEDIA ! OF VOLSET ! ON LDEV !

Store is being to write to a member of the specified volume set.

Information only.

STARTING TO WRITE TO VOL ! OF VOLSET ! ON LDEV !

Store is being to write to a member of the specified volume set.

Information only.

MEMBER OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET

A volume that has already been written to as part of this backup was re-mounted.

Dismount this volume and mount a volume that has not yet been written to as part of this store.

MEDIA ! OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET

A volume that has already been written to as part of this backup was re-mounted.

Dismount this volume and mount a volume that has not yet been written to as part of this store.

VOL ! OF VOLSET ! ON LDEV ! IS PART OF CURRENT STORE SET

A volume that has already been written to as part of this backup was re-mounted.

Dismount this volume and mount a volume that has not yet been written to as part of this store.

OK TO RE-LABEL EXPIRED VOLUME ! (Y/N)

An expired volume with a different volume set id has been mounted for a store.

Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.

OK TO RE-LABEL EXPIRED VOLUME ! AS ! (Y/N)

An expired volume with a different volume set id has been mounted for a store.

Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.

OK TO RE-LABEL EXPIRED VOLUME ! AS ! (Y/N)

An expired volume with a different volume set id has been mounted for a store.

Reply Yes if it is ok to relabel this volume. Reply No if this volume should not be overwritten.

STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \

An unexpired volume was mounted for a store.

Dismount this volume and mount a volume that has expired.

STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \

An unexpired volume was mounted for a store.

Dismount this volume and mount a volume that has expired.

STORE CANNOT OVERWRITE UNEXPIRED VOLUME ! ON LDEV# \

An unexpired volume was mounted for a store.

Dismount this volume and mount a volume that has expired.

MEMBER OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS

A volume mounted for restore has incorrect HDR1 labels.

Mount a valid volume of the specified volume set.

MEDIA ! OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS

A volume mounted for restore has incorrect HDR1 labels.

Mount a valid volume of the specified volume set.

VOL ! OF VOLSET ! ON LDEV ! HAS INCORRECT HDR LABELS

An unexpired volume was mounted for a store.

Dismount this volume and mount a volume that has expired.

MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)

An unlabeled media has been mounted for a labeled store.

Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.

MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)

An unlabeled media has been mounted for a labeled store.

Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.

MAKE UNLABELED MEDIA ON LDEV ! PART OF LABELED SET (Y/N)

An unlabeled media has been mounted for a labeled store.

Reply Yes to the console request if this unlabeled media should be converted to a labeled volume.

VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED

A different labeled volume than the one requested was mounted for a store.

Dismount this volume and mount the requested volume.

VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED

A different labeled volume than the one requested was mounted for a store.

Dismount this volume and mount the requested volume.

VOLUME MOUNTED ON LDEV ! WAS NOT REQUESTED

A different labeled volume than the one requested was mounted for a store.

Dismount this volume and mount the requested volume.

RESTORE SKIPPING SLT IN PROGRESS ON LDEV !

Restore is skipping over the SLT portion of combined SLT/Store.

Information only.

OK TO RESTORE FILES OF SET ! ON LDEV ! (Y/N)

Restore needs verification that the specified restoreset should be restored from the MO at the specified ldev.

Reply "Yes" to the console message if this is the set that should be restored. Reply "No" otherwise.

ARE ALL FILES AND DATABASES QUIESCED FOR ONLINE BACKUP #! ? (Y/N)

You have specified the ASK parameter to the ONLINE option, requesting that TurboSTORE notify via a console request when the True-Online sync point is about to occur.

Make sure that all non-HP databases and other files are ready for the sync point. Then, reply Y to this request if you want the sync point to occur. If you want to cancel this backup, reply N.

DO YOU WANT TO ABORT THE BACKUP? (Y/N)

You have replied "N" to the ASK request during a True-Online backup.

If you reply "Y" to this message, the backup will abort and will be invalid. If you reply "N" to this message, you will be asked if all files and databases are quiesced for an online backup.

ONLINE BACKUP SYNC POINT STARTING

TurboSTORE is starting to quiesce all databases specified for a True-Online backup.

None required, information only. You may notice a pause in database access during the online sync point for all databases being stored by a 7x24 online backup.

ONLINE BACKUP SYNC POINT FINISHED

TurboSTORE has completed the 7x24 online sync point and has unquiesced all databases.

None required, information only. Users should be able to access quiesced databases now.

ALL NON-STANDARD DATABASES CAN BE UNQUIESCED NOW

The 7x24 online sync point has completed.

If you had to manually quiesce any non-HP databases, they can now be unquiesced.

MOUNT LAST MEDIA FOR RESTORE ON LDEV \

RESTORE needs to read the final media directory from the last media of the backup.

Mount the last media of the backup.

MOUNT LAST MEMBER OF VOLSET ! FOR RESTORE ON LDEV \

RESTORE needs to read the final media directory from the last media of the backup.

Mount the last volume of the specified volume set.

STORE/RESTORE ENCOUNTERED A POWERFAIL ON LDEV !

A powerfail or bus reset occurred on the specified LDEV

If this was reported from STORE, STORE will automatically rewind the current media and rewrite the data. If this is reported by RESTORE, the RESTORE will abort, since RESTORE cannot recover from a device powerfail.

STORE/RESTORE ENCOUNTERED A POWERFAIL ON REMOTE DEVICE FILE "!"

A powerfail or bus reset occurred on the specified remove device

If this was reported from STORE, STORE will automatically rewind the current media and rewrite the data. If this is reported by RESTORE, the RESTORE will abort, since RESTORE cannot recover from a device powerfail.

STORE/RESTORE LOST TAPE TENSION ON LDEV !

While accessing a device, a tape tension lost condition was reported.

STORE try to recover from this situation by rewinding the current media and rewriting the reel. RESTORE cannot recover from such a situation and will abort. Make sure your tape devices are clean.

STORE/RESTORE LOST TAPE TENSION ON REMOTE DEVICE FILE "!"

While accessing a remote device, a tape tension lost condition was reported.

STORE try to recover from this situation by rewinding the current media and rewriting the reel. RESTORE cannot recover from such a situation and will abort. Make sure your tape devices are clean.

WARNING: 'FILES' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 301)

The FILES option was entered more than once.

Information only.

EXPECTED '={maxfiles}' AFTER 'FILES' OPTION. SYNTAX 'FILES={maxfiles}' (S/R 302)

You did not type the files parameter correctly.

Check the syntax and retype the command.

SPECIFIED MAXFILES VALUE FOR 'FILES={maxfiles}' EXCEEDS THE MAXIMUM ALLOWED. (S/R 303)

The maximum files limit of the files parameter has been exceeded.

Information only.

EXPECTED 'FILES={maxfiles}' WHERE {maxfiles} IS A POSITIVE INTEGER. (S/R 304)

You have specified a negative 'maxfiles' number.

Information only.

'FILES' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 305)

The files and listdir options are not allowed on the same command line.

Delete either the files or the listdir options.

'RESTORESET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 311)

You entered RESTORESET twice in the command.

Remove one of the RESTORESET options and retype the command.

'RESTORESET' OPTION MAY NOT BE SPECIFIED IN CONJUNCTION WITH A POSITIONAL DEVICE FILE. Ex. 'RESTORE *t;....;RESTORESET=(*t1,*t2)' IS INVALID. (S/R 312)

Restoreset and device file options are not allowed on the same command line.

Delete either restoresest or device file options and retype the command.

EXPECTED '=(device[,,..])[,(device[,...])]' AFTER 'RESTORESET' OPTION. SYNTAX 'RESTORESET=(device[,..])[,(device[,...])]'. (S/R 313)

You did not type the restoreset parameter correctly.

Check the syntax and retype the command.

EXPECTED A '(' TO START A RESTORESET. Ex. 'RESTORESET=(*ta,*tb). SYNTAX 'RESTORE-SET=(device[,...])[device[,...])]' (S/R 314)

You did not include a left parenthesis.

Check the syntax and retype the command.

MAXIMUM NUMBER OF PARALLEL SETS EXCEEDED FOR 'RESTORESET' OPTION. Ex, 'RESTORESET=(*ta),(*tb)' IS TWO PARALLEL SETS. (S/R 315)

You specified too many parallel sets. The maximum is 8.

Specify 8 or fewer parallel sets.

EXPECTED 'device' FILE EQUATION IN RESTORESET. Ex. RESTORESET=(*t SYNTAX 'RESTORESET=(device[,..])[,(device[,...])]'. (S/R 316)

You did not include a file equation to name the backup device.

Specify a file equation.

MAXIMUM NUMBER OF 'device" FILE EQUATIONS EXCEEDED FOR A SERIAL SET. Ex. RESTORESET = (*t1, *t2,..., *tn) EXCEEDS THE MAXIMUM OF 8. (S/R 317)

You specified too many serial file equations. The maximum is 8.

Specify 8 or fewer serial file equation.

EXPECTED A ')' TO TERMINATE A SERIAL THE 'RESTORESET' OPTION. SYNTAX 'RESTORESET=(device[,...])[device[,...])]' (S/R 318)

You did not include a right parenthesis.

Check the syntax and retype the command.

'RESTORESET' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 319)

Restoreset and listdir options are not allowed on the same command line.

Delete either restoreset or listdir option and retype the command.

'RESTORESET' OPTION NOT ALLOWED FOR A SLT/STORE SET (S/R 320)

The restoreset option cannot be used with a combined SLT/ store set tape.

Redo the restore command, using only one backup device, and not specifying the restoreset option.

WARNING: 'PROGRESS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 321)

The PROGRESS option was entered more than once.

Information only.

EXPECTED {#minutes} BETWEEN 1 AND 60. SYNTAX PROGRESS[={#minutes}] (S/R 322)

You did not specify a number within the range.

Specify a number between 1 and 60.

EXPECTED 'PROGRESS={#minutes}' WHERE {#minutes} IS A POSITIVE INTEGER. (S/R 323)

The progress parameter must be greater than zero.

Check your syntax and retype the command.

EXPTECTED '={#minutes}' AFTER 'PROGRESS' OPTION. (S/R 324)

You did not type the progress parameter correctly.

Check the syntax and retype the command.

'STORESET' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 331)

You cannot specify the storeset and transport parameters on the same command line.

Delete either the storeset or the transport parameter from the command line.

'STORESET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 332)

You entered STORESET twice in the command.

Delete one of the STORESET options and retype the command.

'STORESET' OPTION MAY NOT BE SPECIFIED IN CONJUNCTION WITH A POSITIONAL DEVICE FILE. EG 'STORE...;*t;STORESET=(*t1,*t2)' IS VALID. (S/R 333)

You mistyped the storeset parameter.

Check the syntax of the storeset parameter and retype the command.

EXPECTED '=(device[,,..])[,(device[,...])]' AFTER 'STORESET' OPTION. SYNTAX 'STORESET=(device[,..])[,(device[,...])]' (S/R 334)

You did not type the storeset parameter correctly.

Check the syntax and retype the command.

EXPECTED A '(' TO START A STORESET. Ex. 'STORESET=(*ta,*tb). SYNTAX 'STORESET=(device[,...])[,(device[,...])]' (S/R 336)

You did not include the left parenthesis in your command.

Check the syntax and retype the command.

EXPECTED 'device' FILE EQUATION IN STORESET. Ex. STORESET=(*ta,*tb SYNTAX 'STORESET=(device[,..])[,(device[,...])]' (S/R 336)

You did not specify a file equation to name the backup device.

Specify the file equation.

MAXIMUM NUMBER OF 'device' FILE EQUATIONS EXCEEDED FOR A SERIAL SET. Ex. STORESET=(*t1,*t2,...*tn) EXCEEDS THE MAXIMUM OF 8. (S/R 337)

You specify too many serial file equations. the maximum is 8.

Specify 8 or fewer serial file equations.

EXPECTED A ')' TO TERMINATE A SERIAL THE 'STORESET' OPTION. SYNTAX 'STORESET=(device[,...])[(device[,...])]' (S/R 338)

You did not include a right parenthesis.

Check the syntax and retype the command.

'STORESET' OPTION NOT ALLOWED IN SYSGEN/STORE. (S/R 339)

A combined SLT/store set cannot be created by sysgen with the storeset option.

Retype the command without the storeset option, specifying only one backup device.

WARNING: 'TRANSPORT' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 351)

The TRANSPORT option was entered more than once.

Information only.

'TRANSPORT' OPTION NOT ALLOWED IN SYSGEN/STORE. (S/R 352)

Sysgen cannot created a CMStore format tape.

Remove the transport option from the store options and redo the command.

INVALID TARGET SYSTEM ID FOR 'TRANSPORT' KEYWORD. ONLY ID CURRENTLY VALID IS "MPEXL". IF NO TARGET ID IS SPECIFIED THEN THE TARGET SYSTEM DEFAULTS TO MPEv. SYNTAX: TRANSPORT[=MPEXL] (S/R 354)

An invalid transport id was specified.

Specify a legel transport option and redo the command.

WARNING: 'DIRECTORY' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 361)

The DIRECTORY option was entered more than once.

Information only.

'DIRECTORY' OPTION CANNOT BE USED WITH THE 'TRANSPORT' OPTION. (S/R 362)

Directory and transport options are not allowed on the same command line.

Delete either directory or transport option and retype the command.

USE OF THE 'DIRECTORY' OPTION REQUIRES (SM) OR (OP) CAPABILITY. (S/R 363)

You do not have system manager (SM) capability or system operator (OP) capability.

Log on to an account with SM or AM, or have your system manager perform the tasks.

'ONVS' OPTION CANNOT BE USED WITH 'TRANSPORT' TO MPEv. (S/R 371)

ONVS and TRANSPORT options are not allowed on the same command line.

Delete either the ONVS or TRANSPORT option and retype the command.

WARNING: 'ONVS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 372)

The ONVS option was entered more than once.

Information only.

EXPECTED '=volumesetname[,volumesetname...]' AFTER 'ONVS' OPTION. (S/R 373)

You did not type the onvs parameter correctly.

Check the syntax and retype the command.

INVALID VOLUMESET NAME SPECIFIED FOR 'ONVS' OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A - Z' AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_" AND "." SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 374)

Volumeset name mispelled or not recognized on the system.

Enter a system recognized volumeset name.

VOLUMESET NAME SPECIFIED FOR 'ONVS' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32 CHARACTERS. SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 375)

You entered a volumeset name that was more than 32 characters.

Enter a volumeset name that has 32 characters or less.

EXPECTED 'volumesetname[,volumesetname...]' AFTER 'ONVS=' WHERE volumesetname IS THE NAME OF THE VOLUME SET THAT IS CURRENTLY ON YOUR SYSTEM. SYNTAX 'ONVS=volumesetname[,volumesetname...]'. (S/R 376)

You did not type onvs parameter correctly.

Check the syntax and retype the command.

STORE/RESTORE DOES NOT ALLOW MORE THAN TWENTY (20) "volumesetnames" TO BE SPECIFIED FOR THE 'ONVS' OPTION. (S/R 377)

You specify too many volumeset name with the onvs option. the maximum is 20.

Specify 20 or fewer volumesets.

"volumesetname" SPECIFIED DOES NOT EXIST (IS NOT MOUNTED) ON THIS SYSTEM. (S/R 378)

You entered a volumeset name which is not on the system.

Enter a correct volumeset name.

'VOLSET' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 381)

The VOLSET option was entered more than once.

Information only.

'VOLSET' OPTION CANNOT BE USED WITH THE 'DEV' OPTION. (S/R 382)

Volset and dev options are not allowed on the same command line.

Delete either volset or dev option and retype the command.

EXPECTED '=volumesetname' AFTER 'VOLSET' OPTION. SYNTAX 'VOLSET=volumesetname'. (S/R 383)

You did not enter the volset parameter correctly.

Check the syntax and retype the command.

INVALID VOLUMESET NAME SPECIFIED FOR 'VOLSET' OPTION. VOLUMESET NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", "_" OR "." SYNTAX 'VOLSET=volumesetname'. (S/R 384)

Volumeset name mispelled or not recognized on the system.

Enter a system recognized volumeset name.

VOLUMESET NAME SPECIFIED FOR 'VOLSET' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 32 CHARACTERS. SYNTAX 'VOLSET=volumesetname' (S/R 385)

You entered a volumeset name that was more than 32 characters.

Enter a volumeset name that has 32 characters or less.

EXPECTED 'volumesetname' AFTER 'VOLSET=' WHERE volumesetname IS THE NAME OF A VOLUME SET THAT IS CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX 'VOLSET=volumesetname' (S/R 386)

You did not type the volset parameter correctly.

Check the syntax and retype the command.

'VOLSET' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 387)

Volset and listdir options are not allowed on the same command line.

Delete either volset or listdir option and retype the command.

'VOLCLASS' OPTION CANNOT BE USED WITH THE 'VOL' OPTION. (S/R 391)

Volclass and vol options are not allowed on the same command line.

Delete either volclass or vol option and retype the command.

'VOLCLASS' OPTION CANNOT BE USED WITH THE 'DEV' OPTION. (S/R 392)

Volclass and dev options are not allowed on the same command line.

Delete either volclass or dev option and retype the command.

'VOLCLASS' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 393)

The VOLCLASS option was entered more than once.

Information only.

EXPECTED '=volumeclassname' AFTER 'VOLCLASS' OPTION. SYNTAX 'VOLCLASS=volumeclassname' (S/R 394)

You did not type the volclass parameter correctly.

Check the syntax and retype the command.

INVALID VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS' OPTION. VOLUMECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_". SYNTAX 'VOLCLASS=volumeclassname'. (S/R 395)

Volumeclass name mispelled or not recognized on the system.

Enter a system recognized volumeclass name.

VOLUMECLASS NAME SPECIFIED FOR 'VOLCLASS' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS. SYNTAX 'VOLCLASS=volumeclassname' (S/R 396)

You entered a volumeclass name that was more than 16 characters.

Enter a volumeclass name that has 16 characters or less.

EXPECTED 'volumeclassname' AFTER 'VOLCLASS=' WHERE volumeclassname IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX 'VOLCLASS=volumeclassname' (S/R 397)

You did not specify a volumeclass name.

Check the syntax and retype the command.

'VOLCLASS' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 398)

Volclass and listdir options are not allowed on the same command line.

Delete either volclass or listdir option and retype the command.

'VOL' OPTION CANNOT BE USED WITH THE 'VOLCLASS' OPTION (S/R 401)

Vol and volclass options are not allowed on the same command line.

Delete either vol or volclass option and retype the command.

'VOL' OPTION CANNOT BE USED WITH THE 'DEV' OPTION (S/R 402)

Vol and dev options are not allowed on the same command line.

Delete either vol or dev option and retype the command.

'VOL' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 403)

The VOL option was entered more than once.

Information only.

EXPECTED '=volumename' AFTER 'VOL' OPTION. SYNTAX 'VOL=volumename' (S/R 404)

You did not type vol parameter correctly.

Check the syntax and retype the command.

INVALID VOLUME NAME SPECIFIED FOR 'VOL' OPTION. VOLUME NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_". SYNTAX 'VOL=volumename' (S/R 405)

Volume name misspelled or unrecognizable volume name was entered.

Enter the correct volume name.

VOLUME NAME SPECIFIED FOR 'VOL' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS. SYNTAX 'VOL=volumename' (S/R 406)

The volume name you specified is too long. The maximum number of chharacters is 16.

Specify a volume name with 16 or fewer characters.

EXPECTED 'volumename' AFTER 'VOL=' WHERE volumename IS THE NAME OF A VOLUME (DISC) THAT IS CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX 'VOLSET=volumesetname' (S/R 407)

You did not enter the volumename.

Check the syntax and retype the command.

'VOL' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 408)

Vol and listdir options are not allowed on the same command line.

Delete either vol or listdir option and retype the command.

WARNING: 'HIGH' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 411)

The HIGH option was entered more than once.

Information only.

EXPECTED '={datasetnumber}' AFTER 'HIGH' OPTION. SYNTAX 'HIGH={datasetnumber}' (S/R 412)

You did not specify datasetnumber.

Check the syntax and retype the command.

EXPECTED 'HIGH={datasetnumber}' WHERE {datasetnumber} IS A POSITIVE INTEGER DENOTING A DATA SET BETWEEN 0 AND 199. SYNTAX 'HIGH={datasetnumber}' (S/R 413)

You did not type the high parameter correctly.

Check the syntax and retype the command.

EXPECTED {datasetnumber} BETWEEN 0 AND 199. SYNTAX 'HIGH={datasetnumber}' (S/R 414)

You did not specify a number within the range.

Specify a number between 1 and 199.

{datasetnumber} SPECIFIED FOR 'HIGH' OPTION MUST BE GREATER THAN OR EQUAL TO THE VALUE SPECIFIED FOR THE 'LOW' OPTION. SYNTAX 'HIGH={datasetnumber}' (S/R 415)

The high parameter is too small.

Specify a larger number for the high parameter.

WARNING: 'LOW' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 421)

The LOW option was entered more than once.

Information only.

EXPECTED '={datasetnumber}' AFTER 'LOW' OPTION. SYNTAX 'LOW={datasetnumber}' (S/R 422)

You did not specify datasetnumber.

Check the syntax and retype the command.

EXPECTED 'LOW={datasetnumber}' WHERE {datasetnumber} IS A POSITIVE INTEGER DENOTING A DATA SET BETWEEN 0 AND 199. SYNTAX 'LOW={datasetnumber}' (S/R 423)

You did not specify a number within the range.

Specify a number between 1 and 199.

{datasetnumber} SPECIFIED FOR 'LOW' OPTION MUST BE LESS THAN OR EQUAL TO THE VALUE SPECIFIED FOR THE 'HIGH' OPTION. SYNTAX 'LOW={datasetnumber}' (S/R 424)

The low parameter is too large.

Specify a smaller number for low parameter.

EXPECTED {datasetnumber} BETWEEN 0 AND 199. SYNTAX 'LOW={datasetnumber}' (S/R 425)

You did not specify a number within the range.

Specify a number between 1 and 199.

'FCRANGE' OPTION CANNOT BE USED WITH 'TRANSPORT' to MPEv (S/R 431)

Fcrange and transport options are not allowed on the same command line.

Delete either fcrange or transport option and retype the command.

WARNING: 'FCRANGE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 432)

The FCRANGE option was entered more than once.

Information only.

EXPECTED '=filecode/filecode[,filecode/filecode...]' AFTER 'FCRANGE' OPTION. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 433)

You typed the fcrange parameter incorrectly.

Check the syntax and retype the command.

EXPECTED filecode IN FIRST PART OF filecode/filecode OF 'FCRANGE' OPTION TO BE AN INTEGER BETWEEN -32768 AND 32767. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 434)

You typed the fcrange parameter incorrectly.

Check the syntax and retype the command.

SPECIFIED filecode OF 'FCRANGE' OPTION MUST BE AN INTEGER BETWEEN -32768 AND 32767. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 435)

You did not enter a valid file code range.

Enter a valid file code range.

EXPECTED A "/" TO SEPARATE filecode RANGES FOR THE 'FCRANGE' OPTION. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 436)

You typed the fcrange parameter incorrectly.

Check the syntax and retype the command.

EXPECTED filecode IN SECOND HALF OF filecode/filecode OF 'FCRANGE OPTION TO BE AN INTEGER BETWEEN -32768 AND 32767. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 437)

You typed the fcrange parameter incorrectly.

Check the syntax and retype the command.

SECOND filecode OF A filecode/filecode PAIR IN THE 'FCRANGE' OPTION MUST BE GREATER THAN THE FIRST, Ex. 'FCRANGE=1030/1061'. SYNTAX 'FCRANGE=filecode/filecode[,filecode/filecode...]' (S/R 438)

The second file code that you specified was lower than the first.

Retype the command so that the second file code is higher than the first.

MAXIMUM NUMBER OF filecode RANGES (8) EXCEEDED FOR THE FCRANGE OPTION (S/R 439)

You specified too many file code ranges. The maximum number is 8.

Specify 8 or fewer file code ranges.

'FCRANGE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 440)

Fcrange and listdir options are not allowed on the same command line. .

Delete either fcrange or listdir option and retype the command.

WARNING: 'ONERROR' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 441)

The ONERROR option was entered more than once.

Information only.

EXPECTED '={error-parm}' AFTER 'ONERROR' OPTION WHERE error-parm IS ONE OF 'QUIT' OR 'SKIP'. SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 442)

You typed the onerror parameter incorrectly.

Check the syntax and retype the command.

THE 'FULL' PARAMETER OF THE 'ONERROR' OPTION REQUIRES (PM) CAPABILITY (S/R 443)

You do not have PM capability.

Log on to an account with PM capability.

UNKNOWN PARAMETER SPECIFIED FOR THE 'ONERROR' OPTION. EXPECTED ONE OF 'QUIT' OR 'SKIP'. SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 444)

You did not specify a valid onerror option.

Retype the command and specify a valid onerror option.

EXPECTED recovery type FOR THE 'ONERROR' OPTION. EXPECTED ONE OF 'QUIT' OR 'SKIPFULL'. SYNTAX 'ONERR[OR]={QUIT} OR {SKIP}' (S/R 445)''

You typed the onerror parameter incorrectly.

Check the syntax and retype the command.

'ONERROR' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 446)

Onerror and listdir options are not allowed on the same command line.

Delete either onerror or listdir option and retype the command.

'ONERROR=FULL' FUNCTION NOT IMPLEMENTED (S/R 447)

Onerror=full will be supported in the future release.

Information only.

WARNING: 'SHOW' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 451)

The SHOW option was entered more than once.

Information only.

EXPECTED '=showparm[,showparm..]' AFTER 'SHOW' OPTION WHERE showparm IS ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', OR 'SECURITY'. SYNTAX 'SHOW=showparm[,showparm....]' (S/R 452)

You typed the show parameter incorrectly.

Check the syntax and retype the command.

'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW' OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED (LONG) WILL BE USED (S/R 453)

Show=long will be used.

Information only.

'SHORT' AND 'LONG' PARAMETERS OF THE 'SHOW' OPTION HAVE BEEN MERGED. THE FIRST SPECIFIED (SHORT) WILL BE USED (S/R 454)

Show=short will be used.

Information only.

UNKNOWN PARAMETER SPECIFIED FOR THE 'SHOW' OPTION. EXPECTED ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', 'PATH', OR 'SECURITY'. SYNTAX 'SHOW=showparm[,showparm....]' (S/R 455)

You did not type a valid show parameters.

Check the syntax and retype the command.

EXPECTED showparm FOR THE 'SHOW' OPTION. EXPECTED ONE OF 'SHORT', 'LONG', 'DATES', 'OFFLINE', 'PATH', OR 'SECURITY'. SYNTAX 'SHOW=showparm[,showparm....]' (S/R 456)

You type the show parameters incorrectly.

Check the syntax and retype the command.

'SHOW' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 457)

Show and listdir options are not allowed on the same command line.

Delete either show or listdir option and retype the command.

'SHORT' OPTION CANNOT BE USED WITH THE 'NAMESONLY' OPTION (S/R 458)

The namesonly and short suboptions to SHOW cannot be used together.

Retype the command, specifying only one of short or namesonly.

'LONG' OPTION CANNOT BE USED WITH THE 'NAMESONLY' OPTION (S/R 459)

The namesonly and long suboptions to SHOW cannot be used together.

Retype the command, specifying only one of long or namesonly.

WARNING: 'DEV' OPTION HAS BEEN REDUNDANTLY SPECIFIED. LAST SPECIFIED 'DEV' WILL BE USED. (S/R 461)

The DEV option was entered more than once.

Information only.

'DEV' OPTION CANNOT BE USED WITH THE 'VOL' OPTION. (S/R 462)

Dev and vol options are not allowed on the same command line.

Delete either dev or vol option and retype the command.

'DEV' OPTION CANNOT BE USED WITH THE 'VOLCLASS' OPTION. (S/R 463)

Dev and volclass options are not allowed on the same command line.

Delete either dev or volclass option and retype the command.

'DEV' OPTION CANNOT BE USED WITH THE 'VOLSET' OPTION. (S/R 464)

Dev and volset options are not allowed on the same command line.

Delete either dev or volset option and retype the command.

EXPECTED '=ldn' OR '=deviceclass' AFTER 'DEV' OPTION, WHERE ldn IS A LOGICAL DEVICE NUMBER OF A MOUNTED DISC VOLUME AND deviceclass IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM. SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass. (S/R 465)

You did not include a ldn or deviceclass after the dev option.

Retype the command and include ldn or deviceclass.

THE SPECIFIED ldn (LOGICAL DEVICE NUMBER) DOES NOT CORRESPOND TO THE DISC VOLUME THAT IS CURRENTLY MOUNTED ON THE SYSTEM. TO BE MOUNTED, THE VOLUME MUST BE A MEMBER OF AN "OPENED" VOLUME SET (S/R 466)

The system does not recognize ldev number specified.

Enter the correct ldev number and try again.

INVALID DEVICECLASS NAME SPECIFIED FOR 'DEV' OPTION. A DEVICECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_". SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass (S/R 467)

The deviceclass name is misspelled or not recognized by the system.

Retype the command using a valid name.

DEVICECLASS NAME SPECIFIED FOR 'DEV' OPTION EXCEEDED THE MAXIMUM ALLOWABLE LENGTH OF 16 CHARACTERS. SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass. (S/R 468)

You entered deviceclass name that was more than 16 characters.

Enter a deviceclass name that has 16 characters or less.

EXPECTED 'ldn' OR 'deviceclass' AFTER 'DEV=' IN 'DEV' OPTION. WHERE ldn is A LOGICAL DEVICE NUMBER OF A MOUNTED DISC VOLUME AND deviceclass IS THE NAME OF A VOLUME CLASS THAT IS ON A VOLUME SET CURRENTLY MOUNTED ON YOUR SYSTEM. A DEVICECLASS NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9", OR "_". SYNTAX 'DEV=device' WHERE device IS AN ldn OR A deviceclass (S/R 469)

You type the dev parameter incorrectly.

Check the syntax and retype the command.

'DEV' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 470)

Dev and listdir options are not allowed on the same command line.

Delete either dev or listdir option and retype the command.

'GROUP' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 471)

The GROUP option was entered more than once.

Information only.

'GROUP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'LOCAL' OPTION (S/R 472)

Group and local options are not allowed on the same command line.

Delete either group or local option and retype the command.

EXPECTED '=groupname' AFTER 'GROUP' OPTION WHERE groupname IS THE NAME OF "GROUP" WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED. SYNTAX 'GROUP=groupname' (S/R 473)

You typed the group parameter incorrectly.

Check the syntax and retype the command.

EXPECTED 'groupname' TO BE SPECIFIED FOR 'GROUP' OPTION. A groupname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH. SYNTAX 'GROUP=groupname' (S/R 474)

You did not include the groupname for group option.

Check the syntax and retype the command.

'GROUP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 475)

Group and listdir options are not allowed on the same command line.

Delete either group or listdir option and retype the command.

'ACCOUNT' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 481)

The ACCOUNT option was entered more than once.

Information only.

'ACCOUNT' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'LOCAL' & OPTION (S/R 482)

Account and local options are not allowed on the same command line.

Delete either account or local option and retype the command.

EXPECTED '=accountname' AFTER 'ACCOUNT' OPTION WHERE accountname IS THE NAME OF "ACCOUNT" WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED. SYNTAX 'ACC[OUN]T=accountname' (S/R 483)

You did not type the account parameter correctly.

Check the syntax and retype the command.

EXPECTED 'accountname' TO BE SPECIFIED FOR 'ACCOUNT' OPTION. A accountname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH. SYNTAX 'ACC[OUN]T=accountname' (S/R 484)

You did not include the accountname for account option.

Check the syntax and retype the command.

'ACCOUNT' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 485)

Account and listdir options are not allowed on the same command line.

Delete either account or listdir option and retype the command.

WARNING: 'CREATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 501)

The CREATE option was entered more than once.

Information only.

'CREATE' OPTION DEFAULTING TO 'CREATE=ACCOUNT,GROUP,CREATOR' BASED ON YOUR CAPABILITIES. (S/R 502)

Default parameters are used.

Information only.

'CREATE' OPTION DEFAULTING TO 'CREATE=GROUP,CREATOR' BASED ON YOUR CAPABILITIES. NOTE: ONLY GROUPS AND USERS IN YOUR ACCOUNT WILL BE CREATED. (S/R 503)

Create only creating groups and users in your account.

Information only.

'CREATE' OPTION REQUIRES (SM) CAPABILITY FOR 'ACCOUNT' PARAMETER AND (SM) AND/OR (AM) CAPABILITY FOR 'GROUP' AND 'CREATOR' PARAMETERS. (S/R 504)

You do not have system manager (SM) capability.

Log on to an account with SM or have your system manager perform the tasks.

'GROUP' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) AND/OR (AM) CAPABILITY. NOTE: (AM) CAPABILITY WILL ONLY ALLOW YOU TO CREATE GROUPS IN YOUR HOME ACCOUNT (S/R 505)

You do not have system manager (SM) capability or account manager (AM) capabilities for this account.

Log on to an account with system manager (SM) capability or have your system manager perform the tasks.

NOTE: WITH (AM) CAPABILITY 'GROUP' PARAMETER OF THE 'CREATE' OPTION WILL ONLY ALLOW YOU TO CREATE GROUPS IN YOUR HOME ACCOUNT. (S/R 506)

You may only create groups in your home account.

Information only.

'USER' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) AND/OR (AM) CAPABILITY. NOTE: (AM) CAPABILITY WILL ONLY ALLOW YOU TO CREATE USERS IN YOUR HOME ACCOUNT (S/R 507)

You do not have system manager capability or account manager capability.

Log on to an account with SM or have your system manager perform the tasks.

'ACCOUNT' PARAMETER OF THE 'CREATE' OPTION REQUIRES (SM) CAPABILITY (S/R 508)

Same as message content.

Include account parameter for the create option.

NOTE: WITH (AM) CAPABILITY 'USER' PARAMETER OF THE 'CREATE' OPTION WILL ONLY ALLOW YOU TO CREATE USER IN YOUR HOME ACCOUNT (S/R 509)

You may only create users in your home account.

Information only.

UNKNOWN PARAMETER SPECIFIED FOR THE 'CREATE' OPTION. EXPECTED ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'. SYNTAX 'CREATE[=createparm[,createparm....]]' WHERE createparm IS ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR' (S/R 510)

You did not specify a valid create parameter.

Retype the command and include a valid create parameter.

EXPECTED createparm FOR THE 'CREATE' OPTION. EXPECTED ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'. SYNTAX 'CREATE[=createparm[,createparm....]]' WHERE createparm IS ONE OF 'ACCOUNT', 'GROUP', OR 'CREATOR'. (S/R 511)

You did not include the create parameter.

Retype the command and include a create parameter.

'CREATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 512)

Create and listdir options are not allowed on the same command line.

Delete either create or listdir option and retype the command.

'CREATE' OPTION DEFAULTING TO 'CREATE=PATH' BASED ON YOUR CAPABILITIES. NOTE: ONLY PATHS ALLOWED BY SECURITY RULES WILL BE CREATED (S/R 513)

Since no suboptions were given to CREATE, the default suboption is PATH, based on the user's capabilities.

Information only.

'CREATOR' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 521)

The CREATOR option was entered more than once.

Information only.

EXPECTED '=username' AFTER 'CREATOR' OPTION WHERE username IS THE NAME OF "USER" WHO EXISTS IN THE ACCOUNT WHERE THE SPECIFIED SET OF FILES IS TO BE RESTORED SUCH THAT THE SPECIFIED USER IS TO BE THE NEW "CREATOR" OF THE FILES. SYNTAX 'CREATOR[=username]' WHERE 'CREATOR' WITH NO "username" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE. (S/R 522)

You did not specify a valid creator parameter.

Check the syntax and retype the command.

EXPECTED 'username' TO BE SPECIFIED FOR 'CREATOR' OPTION. A username NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH. SYNTAX 'CREATOR[=username]' WHERE 'CREATOR' WITH NO "username" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE. (S/R 523)

You did not specify the username for the creator option.

Retype the command and include the username.

'CREATOR' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 524)

Creator and listdir options are not allowed on the same command line.

Delete either creator or listdir option and retype the command.

! NOT RESTORED: FILE CREATOR REQUIRES (ND) CAPABILITY (S/R 525)

You can not restore this file becuase you need to have non-sharable device capability.

As the system manager or operator to restore this file for you.

EXPECTED 'acctname' TO BE SPECIFIED FOR 'CREATOR' OPTION. AN acctname NAME MUST START WITH AN ALPHA "A-Z" AND CONTAIN ONLY ALPHANUMERIC "A-Z, 0-9" NOT EXCEEDING 8 CHARACTERS IN LENGTH. SYNTAX 'CREATOR[=username[.acctname]]' WHERE 'CREATOR' WITH NO "username" AND "acctname" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE (S/R 526)

The acctname suboption was missing from the creator option.

Check the syntax of the creator option and retype the command.

EXPECTED '.' TO BE SPECIFIED AFTER username FOR 'CREATOR' OPTION. SYNTAX 'CREATOR[=username[.acctname]]' WHERE 'CREATOR' WITH NO "username" AND "acctname" SPECIFIED DEFAULTS TO THE ORIGNAL CREATOR OF THE FILE (S/R 527)

The acctname part of the creator option was not specified correctly.

Check the syntax of the acctname part of creator and retype the command.

WARNING: 'LOCAL' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 531)

The LOCAL option was entered more than once.

Information only.

'LOCAL' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'GROUP' OPTION (S/R 532)

Local and group options are not allowed on the same command line.

Delete either local or group option and retype the command.

'LOCAL' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'ACCOUNT' OPTION (S/R 533)

Local and account options are not allowed on the same command line.

Delete either local or account option and retype the command.

'LOCAL' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 534)

Local and listdir options are not allowed on the same command line.

Delete either local or listdir option and retype the command.

WARNING: 'KEEP' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 541)

The KEEP option was entered more than once.

Information only.

'KEEP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'NOKEEP' OPTION. (S/R 542)

Keep and nokeep options are not allowed on the same command line.

Delete either keep or nokeep option and retype the command.

'KEEP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 543)

Keep and listdir options are not allowed on the same command line.

Delete either keep or listdir option and retype the command.

WARNING: 'NOKEEP' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 551)

The NOKEEP option was entered more than once.

Information only.

'NOKEEP' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'KEEP' OPTION. (S/R 552)

Nokeep and keep options are not allowed on the same command line.

Delete either nokeep or keep option and retype the command.

'NOKEEP' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 553)

Nokeep and listdir options are not allowed on the same command line.

Delete either nokeep or listdir option and retype the command.

WARNING: 'OLDDATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 561)

The OLDDATE option was entered more than once.

Information only.

'OLDDATE' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'NEWDATE' OPTION. (S/R 562)

Olddate and newdate options are not allowed on the same command line.

Delete either olddate or newdate option and retype the command.

'OLDDATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 563)

Olddate and listdir options are not allowed on the same command line.

Delete either olddate or listdir option and retype the command.

WARNING: 'NEWDATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 571)

The NEWDATE option was entered more than once.

Information only.

'NEWDATE' OPTION CANNOT BE USED IN CONJUNCTION WITH THE 'OLDDATE' OPTION. (S/R 572)

Newdate and olddate options are not allowed on the same command line. .

Delete either newdate or olddate option and retype the command.

'NEWDATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION. (S/R 573)

Newdate and listdir options are not allowed on the same command line. .

Delete either newdate or listdir option and retype the command.

'LISTDIR' OPTION CANNOT BE USED IN CONJUNCTION WITH ANY OTHER OPTION ASIDE FROM THE 'DIRECTORY' OPTION. (S/R 581)

Same as the message content.

Information only.

WARNING: 'DATE' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 591)

The DATE option was entered more than once.

Information only.

EXPECTED '<=accdate' OR '>=moddate' AFTER 'DATE' OPTION WHERE '<= PRIOR TO OR THE SAME AS THAT DATE WILL BE SELECTED FOR STORE, AND '>=moddate' SPECIFIES A DATE SUCH THAT FILES MODIFIED AFTER OR ON THAT DATE WILL BE SELECTED FOR STORE. SYNTAX 'DATE>=moddate' OR 'DATE<=accdate'. (S/R 592)

You did not type the date parameter correctly.

Check the syntax and retype the command.

THE MONTH PORTION OF SPECIFIED DATE MUST BE BETWEEN 1 AND 12. DATE SYNTAX 'mm/dd/yy[yy]' (S/R 593)

You did not specify a valid number for the month parameter.

Check the syntax and enter a valid number.

A SLASH "/" WAS EXPECTED TO SEPARATE THE MONTH (mm) FROM THE DAY (dd) IN THE SPECIFIED DATE. SYNTAX 'mm/dd/yy[yy]' (S/R 594)

You did not include a slash.

Check the syntax and retype the command.

DAY PORTION OF DATE IS INVALID. IT MUST BE BETWEEN 1 AND 28, 29, 30, OR 31 BASED ON THE SPECIFIED DATE. SYNTAX 'mm/dd/yy[yy]' (S/R 595)

You did not include a valid number for day parameter.

Check the syntax and enter a valid number for day parameter.

A SLASH "/" WAS EXPECTED TO SEPARATE THE MONTH (dd) FROM THE YEAR (yy[yy]) IN THE SPECIFIED DATE. SYNTAX 'mm/dd/yy[yy]' (S/R 596)

You did not include a slash.

Check the syntax and retype the command.

YEAR PORTION OF DATE IS INVALID. IT MUST BE GREATER THAN 1970 (70) AND LESS THAN 2127 OR 99 FOR 1999. DATE SYNTAX 'mm/dd/yy[yy]' (S/R 597)

You did not include a valid number for the year parameter.

Check the syntax and enter a valid number for the year parameter.

EXPECTED MONTH (mm) PORTION OF DATE. SPECIFIED MONTH VALUE MUST BE BETWEEN 1 AND 12. DATE SYNTAX 'mm/dd/yy[yy]' (S/R 598)

You did not include month parameter for date option.

Check the syntax and retype the command.

EXPECTED DAY (dd) PORTION OF DATE. SPECIFIED DAY VALUE MUST BE BE BETWEEN 1 AND 28, 29, 30, OR 31 BASED ON THE SPECIFIED MONTH. DATE SYNTAX 'mm/dd/yy[yy]' (S/R 599)

You did not include day parameter for date option.

Check the syntax and retype the command.

EXPECTED YEAR (yy[yy]) PORTION OF DATE. SPECIFIED YEAR VALUE MUST BE GREATER THAN 1970 (70) AND LESS THAN 2127 OR 99 FOR 1999. DATE SYNTAX 'mm/dd/yy[yy]' (S/R 600)

You did not include year parameter for date option.

Check the syntax and retype the command.

'DATE' OPTION CANNOT BE USED WITH THE 'LISTDIR' OPTION (S/R 601)

Date and listdir options are not allowed on the same command line.

Delete either date or listdir option and retype the command.

WARNING: 'PURGE' OPTION HAS BEEN REDUNDANTLY SPECIFIED (S/R 611)

The PURGE option was entered more than once.

Information only.

WARNING: 'ONERROR' OPTION HAS BEEN REDUNDANTLY SPECIFIED. (S/R 631)

The ONERROR option was entered more than once.

Information only.

EXPECTED '=error-parm' AFTER 'ONERROR' OPTION WHERE error-parm IS EITHER 'QUIT' OR 'REDO'. SYNTAX 'ONERR[OR]={QUIT}, OR {REDO} (S/R 632)

You did not type the onerror parameter correctly.

Check the syntax and retype the command.

UNKNOWN PARAMETER SPECIFIED FOR THE 'ONERROR' OPTION. EXPECTED EITHER 'QUIT' OR 'REDO'. SYNTAX 'ONERR[OR]={QUIT}, OR {REDO} (S/R 633)

You typed a invalid onerror parameter.

Retype the command and include a valid onerror parameter.

EXPECTED '=(read cnt),(queued writes),(outstanding writes)' AFTER 'TUNE' OPTION. SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 641)

You did not type the tune parameter correctly.

Check the syntax and retype the command.

EXPECTED '(read cnt),(queued writes),(outstanding writes)' AFTER 'TUNE=' IN 'TUNE' OPTION. SYNTAX 'TUNE=(read cnt), (queued writes), (outstanding writes)' (S/R 642)

You did not specify a valid tune parameter.

Check the syntax and retype the command.

EXPECTED (read cnt) OF 'TUNE' OPTION TO BE BETWEEN 1 and 12. SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 642)

The read cnt parameter is not in the correct range.

Retype the command and include a valid number.

EXPECTED '(queued writes),(outstanding writes)' AFTER 'TUNE=(read cnt)' IN 'TUNE' OPTION. SYNTAX 'TUNE=(read cnt),(queued writes),(outstanding writes)' (S/R 644)

You did not type the tune parameter correctly.