 |
» |
|
|
|
|  |  |
This chapter lists the messages that you may encounter while managing
printers, tapes and spoolers. - 1
- MESSAGE
(MAX CHARS=num)?
- CAUSE
A message was sent to you by the PRINTOPREPLY intrinsic.
- ACTION
REPLY/=REPLY to the message.
- 2
- MESSAGE
CAN'T INITIALLY SPOOL LDEV#nnn
- CAUSE
A nonspoolable ldev was configured to be initially spooled. You need
to specify either a legitimate spoolee (an ldev capable of being
spooled) or an ldev that is job/session accepting.
- ACTION
This indicates a system configuration error.
The device specified cannot be spooled.
The ACCEPT [JOBS,]ldev command can be used to allow the JOB
command if the device is a legitimate input spoolee; then
use STARTSPOOL ldev to start the spooler.
- 3
- MESSAGE
FORMS: formsmessage
- CAUSE
A user has requested special forms to be mounted on a line printer. The device file and job number are printed on the following device assignment request by the PIN.
- ACTION
Information only.
- 4
- MESSAGE
LDEV nnn,UNABLE TO ALLOCATE $STDLIST
- CAUSE
$STDLIST not able to be allocated.
- ACTION
Recovery from this type of overload is automatic in a session.
In a batch job, the spooling queues have shut or the system has exceeded
the MAX # OF OPEN SPOOLFILES. Check the output device of the jobs
in the WAIT state with SHOWDEVnn to see if it is
unavailable (queue shut). If so, reopen the spool queue
with OPENQ. If the printer is listed as AVAIL,
enter an OPENQ command or a STARTSPOOL command to
restart the printer.
If there is a lack of disk space, you may
have to store off spoolfiles, or use START NORECOVERY with the RECOVER LOST DISC SPACE option, before using OPENQ.
- 5
- MESSAGE
LDEV#nnn FORMS ALIGNED OK (Y/N)?
- CAUSE
You are asked by the system, following the printing of the standard "forms alignment image," if the forms are positioned correctly on the specified ldev.
- ACTION
You are required to enter =REPLY pin, YES or =REPLY pin , NO. If the image is correctly positioned, =REPLY, YES and the requesting program will continue.
If the image is not correctly positioned, reposition the forms
and ~~=REPLY, ~~NO''. This will cause the alignment
image to be printed again, and the question will be reissued.
For a CIPER device, the forms alignment image must be printed using
printer controls. It is not automatically printed by MPE/iX.
- 6
- MESSAGE
LDEV#nnn IN USE, DOWN PENDING
- CAUSE
You have issued a DOWN command, but the device is in use by a process.
- ACTION
As soon as the use count goes to zero, the device will be down,
and you will be notified.
- 7
- MESSAGE
LDEV#nnn NOT READY
- CAUSE
The specified device is offline or the media is not mounted. If other action is required such as changing the tape reel, the program will display messages to that effect.
- ACTION
Place the device online.
- 8
- MESSAGE
LDEV#nnn OFFLINE
- CAUSE
You are trying to access a device that is no longer available to the file system.
- ACTION
If the device is functional, enter UP ldev to place device online.
- 9
- MESSAGE
LDEV#nnn PAPER OUT
- CAUSE
You ran out of paper on the indicated device.
- ACTION
Install and align the paper, and place the device online.
- 10
- MESSAGE
LDEV#nnn QUEUE EMPTY NO I/O TO ABORT FOR DEVICE nnn
- CAUSE
You attempted an ABORTIO or =ABORTIO,
and no requests were pending on the device.
- ACTION
Information only.
- 11
- MESSAGE
LDEV#nnn UNIT FAILURE
- CAUSE
Bad status was returned from the specified logical device.
- ACTION
Retry. If the problem persists call your Application Engineering Organization (AEO).
- 12
- MESSAGE
MAX SPOOFLE KILOSECTORS IN USE, ALL QUEUES SHUT
- CAUSE
The configured maximum number of spooled device file kilosectors
are in use. MPE/iX shuts all output queues (equivalent to
SHUTQ ldev), on all ldevs and SHUTQ
devclass on all device classes), so users are automatically
prevented from creating new spooled device files.
- ACTION
When space becomes available, you may reopen the queues with the OPENQ command.
- 13
- MESSAGE
NO MORE SPACE IN SPOOL CLASS, ALL QUEUES SHUT
- CAUSE
No more space exists in the (disk) class SPOOL. MPE/iX shuts all
output queues (equivalent to SHUTQ ldev on all ldevs and SHUTQ devclass on all device classes), so users are automatically prevented from creating new spooled device files.
- ACTION
Store on tape unnecessary spoolfiles
and purge them from the system.
A long term solution would be to reconfigure the system
using SYSGEN for more disk space.
When space becomes available, you may reopen the queues with the OPENQ command.
- 14
- MESSAGE
REQUEST REQUIRING OPERATOR REPLY FOR PIN pin HAS BEEN ABORTED.
- CAUSE
A request for operator response (for example, =REPLY/REPLY)
for pin is no longer pending. The user probably hit BREAK and
entered ABORT
- ACTION
Informational only.
- 15
- MESSAGE
SP#nnn/#Onnn DEFERRED
- CAUSE
The output spooler on the specified ldev has deferred the
spooled device file with the specified device file identification
Onnn), due to some action taken by you (for example,
refusing a spooler's forms request).
- ACTION
To allow the deferred device file to print from the beginning,
enter ALTSPOOLFILE #Onnn;PRI=k (where k
is a value above the current outfence).
- 16
- MESSAGE
SP#nnn/#Onnn DEFERRED, SPOOFLE I/O ERROR
- CAUSE
The output spooler on ldev has encountered an error while opening or reading the spooled device file with identification #Onnn. The spooler has deferred the file.
- ACTION
To allow the deferred device file to try to print again use ALTSPOOLFILE #Onnn;PRI=k (where k is a value above the current outfence). To delete the file, enter DELETESPOOLFILE command.
- 17
- MESSAGE
SP#nnn/#Innn DELETED, SPOOFLE I/O ERROR
- CAUSE
The input spooler on the specified spoolee ldev has deleted
spooled device file #Innn due to a disk I/O error or a problem obtaining disk space.
- ACTION
Ensure that a sufficient space exists for the spooled device file.
The system operator should enter the DISCFREE command.
Check free space for all SPOOL class disks. Delete unnecessary
spooled device files if possible. Allow output spoolers to free
up space and try input operation again. Try to recover transient disk
space by doing a START NORECOVERY, if trouble is not indicated.
- 18
- MESSAGE
SP#nnn/IS jobnum;filename ON LDEV#nnn (Y/N)?
- CAUSE
You are asked to verify that you did request jobnum;filename
forms on the device (ldev) indicated.
- ACTION
Enter ~~=REPLY pin, YES to confirm that forms were requested or ~~=REPLY pin, NO to reject the request, and defer the spoolfile.
- 19
- MESSAGE
SP#nnn/SPOOLED IN
- CAUSE
The spooler on the specified spoolee ldev has begun input spooling.
- ACTION
Information only.
- 20
- MESSAGE
SP#nnn/SPOOLED OUT
- CAUSE
The spooler on the specified spoolee ldev has begun output spooling.
- ACTION
Information only.
- 21
- MESSAGE
SP#nnn/STOPPED
- CAUSE
A spooler has terminated on the specified spoolee ldev.
- ACTION
None.
- 22
- MESSAGE
SP#nnn/#InnnDELETED, SPOOFLE I/O ERROR
- CAUSE
The input spooler on the specified spoolee ldev has detected
a disk I/O error or a problem obtaining disk space for a spooled device file. The spooler stops, and the active device file is deleted.
- ACTION
Ensure that sufficient space exists for the spooled device file.
Have the system manager use the DISCFREE command to check
the free space for all SPOOL class disks. Delete unnecessary
spooled device files if possible. Allow output spoolers to free
up space and try input operation again. If the trouble is not
disk space, then a disk I/O error is indicated.
- 23
- MESSAGE
SP#nnn/STOPPED, SPOOLEE I/O ERROR
- CAUSE
The spooler on the indicated spoolee ldev has detected an error in attempting to read, write, or control its spoolee. The
spoolee stops immediately; an input spooler will delete its
currently ACTIVE spooled device file, while an
output spooler will close its currently ACTIVE spooled
device file. May be
attempting a rewind on a magnetic tape device
without a tape mounted. This generally indicates a hardware
problem, but can also occur in response to an ABORTIO
command.
- ACTION
Try to restart the spooler STARTSPOOLldev. If the
problem persists, the device or the medium (disk, magnetic tape)
is faulty. If device is magnetic tape, check that a
tape is mounted.
- 24
- MESSAGE
SP#nnn/STOPPED, SPOOLEE NOT ACCEPTING
- CAUSE
The specified ldev is neitherjob-accepting nor data-accepting,
causing the input spooler to stop. It cannot recognize
further JOB or DATA commands.
- ACTION
Use the ACCEPT JOBS,ldev command or the ACCEPT DATA,ldev command and STARTSPOOL ldev to restart the input spooler.
- 25
- MESSAGE
STANDARD FORMS ON LDEV #nnn
- CAUSE
You have special forms mounted on a device, and a device file not requiring special forms is assigned to the device.
- ACTION
Reply to the message by entering either ~~=REPLY pin, YES
when standard forms are mounted or ~~=REPLY pin, NO
when special forms are mounted and printing is to be deferred.
- 26
- MESSAGE
UNABLE TO ALLOCATE $STDLIST FOR Jnn JOB WAITING
- CAUSE
$STDLIST not able to be allocated.
- ACTION
None.
- 27
- MESSAGE
LDEV #nnn Tape Has Lost Tension - MISLOAD ERROR
- CAUSE
The leader on the tape is not long enough. It must be at least
12 feet.
- ACTION
Load a new tape, or move the "Beginning Of
Tape" marker on the current tape.
|