(Subsystem 148)

An error occurred in the file name from tape.

Incorrect file name read from tape.

Clean tape drive and retry. Clean tape drive and remake tape. Determine cause of incorrect file name on tape and correct.

The procedure failed to initialize the file system directory on INSTALL.

Error status returned from DRINIT file system initialize directory.

Determine cause of error from DRINIT and correct.

An internal file number error occurred upon trying to get the disk address of a boot file.

File number error while getting disk address. (Internal error.)

Call your Hewlett-Packard Representative.

An error occurred from file system FFILEINFO getting the disk address of a boot file.

Error returned from FFILEINFO.

Determine cause of error from FFILEINFO and correct.

An error occurred from file system LM_GET_1ST_EXTENT_INFO getting a disk address of a boot file.

Error returned from LM_GET_1ST_EXTENT_INFO

Determine cause of error from LM_GET_1ST_EXTENT_INFO and correct.

An error occurred from I/O system reading the label for a name file from tape for RENDEZVOUSIO.

Error returned by RENDEZVOUSIO reading MPEXLDIR file label.

Clean tape drive and retry. Clean tape drive, remake tape and retry. Determine cause of error from RENDEZVOUSIO and correct.

An error occurred from I/O system reading the label for a name file from the tape from SENDIO.

Error returned by SENDIO reading MPEXLDIR file label.

Determine cause of error from SENDIO and correct.

An error occurred reading the label for the name file. Bad tape or wrong tape position; not enough data read.

Error in length of data reading MPEXLDIR file label. Tape read expected 256 bytes and got less than 200 bytes.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error occurred from I/O system reading the name file from the tape from RENDEZVOUSIO.

Error returned by RENDEZVOUSIO reading MPEXLDIR file data.

Clean tape drive and retry. Clean tape drive, remake tape and retry. Determine cause of error from RENDEZVOUSIO and correct.

An error occurred from I/O system reading the name file from the tape from SENDIO.

Error returned by SENDIO reading MPEXLDIR file data.

Determine cause of error from SENDIO and correct.

An error occurred reading the name file from the tape; bad tape or wrong tape position; not enough data read.

Error in length of data reading MPEXLDIR file data. Tape read expected at least 80 bytes and got less than 80 bytes.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error occurred from HPFOPEN to create the name file.

Error from HPFOPEN for MPEXLDIR file.

Determine cause of error from HPFOPEN and correct.

Error from FWRITE on writing name file.

Error from FWRITE for MPEXLDIR file.

Determine cause of error from FWRITE and correct.

An error occurred from FCLOSE on the name file.

Error from FCLOSE for MPEXLDIR file.

Determine cause of error from FCLOSE and correct.

A failure occurred from INIT_BOOTCMD_AREA.

Error from INIT_BOOTCMD_AREA.

Determine cause of error from INIT_BOOTCMD_AREA and correct.

A failure occurred from SAVE_BOOTCMD_TO_DISK.

Error from SAVE_BOOTCMD_TO_DISK.

Determine cause of error from SAVE_BOOTCMD_TO_DISK and correct.

A failure occurred from COMPUTE_FREE_ADDRESS.

Error from COMPUTE_FREE_ADDRESS.

Determine cause of error from COMPUTE_FREE_ADDRESS and correct.

This is an invalid free space map address from COMPUTE_FREE_ADDRESS; conditional debug compile option.

Incorrect free space bit map address from COMPUTE_FREE_ADDRESS. Debug code not released.

Call your Hewlett-Packard Representative.

A failure occurred from SM_CREATE_HASH_TBL.

Error from SM_CREATE_HASH_TBL. Internal storage management routine.

Determine cause of error from SM_CREATE_HASH_TBL and correct.

A failure occurred from INSTALL_VOLUME_MGT.

Error from INSTALL_VOLUME_MGT while initializing a volume.

Determine cause of error from INSTALL_VOLUME_MGT and correct.

A failure occurred from local routine LOAD_POST writing to sector 0,1 of disk.

Error from LOAD_POST writing to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

A failure occurred from local routine LOAD_POST writing to sector 0,1 of disk.

Error from LOAD_POST writing to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

A failure occurred from file system FS_INITIALIZE_FILE_SYSTEM.

Error from FS_INITIALIZE_FILE_SYSTEM.

Determine cause of error from FS_INITIALIZE_FILE_SYSTEM and correct.

A failure occurred from file system FS_PROC_INIT.

Error from FS_PROC_INIT, file system initialize routine.

Determine cause of error from FS_PROC_INIT and correct.

A failure occurred from file system directory FAKE_LOGON.

Error from FAKE_LOGON, file system directory routine.

Determine cause of error from FAKE_LOGON and correct.

A failure occurred from file system FS_TDIRC_INIT.

Error from FS_TDIRC_INIT, file system routine.

Determine cause of error from FS_TDIRC_INIT and correct.

A failure occurred from local routine LOAD_POST writing to sector 0,1 of disk.

Error from LOAD_POST writing to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

A fatal option error occurred (file name wrong); INSTALL renamed UPDATE.

A copy of the PME INSTALL has been given control from the option routine with the indication that the command used to call the PME was not INSTALL. Probably was UPDATE. Probably a copy of INSTALL was renamed UPDATE.

Use a correct copy of INSTALL.

Disk sparing failed on LDEV 1.

Error returned from disk sparing of LDEV 1.

Determine cause of error from sparing and correct.

REBOOT_CPU returned control.

The routine REBOOT_CPU has returned control to the caller. The CPU was probably not rebooted.

Determine why control was returned from REBOOT_CPU and correct. Reboot the CPU and continue.

Hard loop failed, probably due to compiler or hardware error, or START/NO START error.

The compiler generated loop to stop the CPU on a nostart option has exited. Generated code or hardware error.

Determine why the code exited and correct. Reboot the CPU and continue.

An error occurred upon getting the size of the disk.

Error from GET_HPE_DISC_SIZE_PAGE. Internal routine to compute the number of pages on the disk.

Determine cause of error from GET_HPE_DISC_SIZE_PAGE and correct.

An error occurred from SM_CREATE_HASH_TBL.

Error from SM_CREATE_HASH_TBL, storage management routine.

Determine cause of error from SM_CREATE_HASH_TBL and correct.

An error occurred from START_VOLUME_MGT.

Error from START_VOLUME_MGT, volume management routine.

Determine cause of error from START_VOLUME_MGT and correct.

An error occurred from file system FS_INITIALIZE_FILE_SYSTEM.

Error FS_INITIALIZE_FILE_SYSTEM.

Determine cause of error from FS_INITIALIZE_FILE_SYSTEM and correct.

An error occurred from file system FS_PROC_INIT.

Error from FS_PROC_INIT, file system routine.

Determine cause of error from FS_PROC_INIT and correct.

An error occurred from file system directory FAKE_LOGON.

Error from FAKE_LOGON, file system directory logon.

Determine cause of error from FAKE_LOGON and correct.

An error occurred from file system FS_TDIRC_INIT.

Error from FS_TDIRC_INIT, file system routine.

Determine cause of error from FS_TDIRC_INIT and correct.

This is a fatal option error (filename wrong); UPDATE renamed INSTALL.

A copy of the PME UPDATE has been given control from the option routine with the indication that the command used to call the PME was not UPDATE. Probably was INSTALL. Probably a copy of UPDATE was renamed INSTALL.

Use a correct copy of UPDATE.

Disk sparing failed on LDEV 1.

Error returned from disk sparing of LDEV 1.

Determine cause of error from sparing and correct.

REBOOT_CPU returned control.

The routine REBOOT_CPU has returned control to the caller. The CPU was probably not rebooted.

Determine why control was returned from REBOOT_CPU and correct. Reboot the CPU and continue.

Hard loop failed, probably due to compiler or hardware error, or START/NO START option error.

The compiler generated loop to stop the CPU on a nostart option has exited. Generated code or hardware error.

Determine why the code exited and correct. Reboot the CPU and continue.

Failure from SAVE_BOOT_CMD_TO_DISC.

Error from SAVE_BOOT_CMD_TO_DISC.

Determine cause of error from SAVE_BOOT_CMD_TO_DISC and correct.

An error was returned by CONFIGURE_DEVICE configuring the tape drive.

Error from CONFIGURE_DEVICE for tape control.

Determine cause of error from CONFIGURE_DEVICE and correct.

The procedure found a second IPL on tape; bad tape.

Found second IPL file on the tape. Invalid tape format.

Determine cause of the second IPL on the tape and correct. Remake the tape and redo the UPDATE or INSTALL.

An error was returned by ADD_DUMP_FILE.

Error returned from ADD_DUMP_FILE. Internal routine to add the dump file to the disk and the LIF directory.

Determine cause of error from ADD_DUMP_FILE and correct.

An error was received from LOAD_POST writing label sector 0,1 to LDEV 1.

Error from LOAD_POST writing to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

No IPL from the tape; disk will not boot.

No IPL file was found on the tape. Invalid tape format.

Determine the cause of missing IPL file and correct. Remake the tape and redo the UPDATE or INSTALL.

No NL.PUB.SYS from the tape; disk will not start.

No NL.PUB.SYS file was found on the tape. Invalid tape format. File is identified by start number in tape file header.

Determine the cause of missing NL.PUB.SYS file and correct. Remake the tape and redo the UPDATE or INSTALL.

An error was received from CREATE_OBJECT for global area.

Error returned from CREATE_OBJECT for global area.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for page 1 buffer.

Error returned from CREATE_OBJECT for page 1 buffer.

Determine cause of error from CREATE_OBJECT and correct.

Bad sector table index error.

An internal error occurred in the disk sparing routine change sector state. Bad sector table index error.

Retry the function (INSTALL or UPDATE or START or mount volume). Write over sector zero to bypass sparing on this volume and initialize it again. Consult a Hewlett-Packard System Engineer for help.

Error on read of TRACK TABLE from RENDEZVOUSIO.

Error returned from RENDEZVOUSIO for sparing read track table.

Determine cause of error from RENDEZVOUSIO and correct.

Error on read of TRACK TABLE from SENDIO.

Error returned from SENDIO for sparing read track table.

Determine cause of error from SENDIO and correct.

Error on write of TRACK TABLE from RENDEZVOUSIO.

Error returned from RENDEZVOUSIO for sparing write track table.

Determine cause of error from RENDEZVOUSIO and correct.

Error on write of TRACK TABLE from SENDIO.

Error returned from SENDIO for sparing write track table.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO reading bad sector.

Error returned from SENDIO for sparing read sector save sector.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO writing sector.

Error returned from SENDIO for sparing write sector save sector.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO reading sector from save area.

Error returned from SENDIO for sparing read sector for restore sector.

Determine cause of error from SENDIO and correct.

An error was received from RENDEZVOUSIO writing sector to new home.

Error returned from RENDEZVOUSIO for sparing write sector for restore.

Determine cause of error from RENDEZVOUSIO and correct.

An error was received from SENDIO writing sector to new home.

Error returned from SENDIO for sparing write sector for restore sector.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO reading sector from track.

Error returned from SENDIO for sparing read sector save track.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO writing sector to save area.

Error returned from SENDIO for sparing write sector save track.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO reading sector from track save area.

Error returned from SENDIO for sparing read sector for restore track.

Determine cause of error from SENDIO and correct.

An error was received from RENDEZVOUSIO writing sector to new home.

Error returned from RENDEZVOUSIO for sparing write sector for restore track.

Determine cause of error from RENDEZVOUSIO and correct.

An error was received from SENDIO writing sector to new home.

Error returned from SENDIO for sparing write sector for restore track.

Determine cause of error from SENDIO and correct.

This is a bad SECTOR TABLE index error.

Internal error. Error in sector state in bad sector table.

Retry the function (INSTALL, UPDATE, START or mount volume). Write over sector zero to bypass sparing on this volume and initialize it again. Call your Hewlett-Packard Representative.

An error was received from SENDIO running sector test.

Error returned from SENDIO for sparing run sector test.

Determine cause of error from SENDIO and correct.

This is an internal error; error in track start address.

Internal debug error. Not released. Invalid sector number from caller for run track test.

Call your Hewlett-Packard Representative.

An error was received from SENDIO running track test.

Error returned from SENDIO for sparing run track test.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO running R.O. track test.

Error returned from SENDIO for sparing run R.O. track test.

Determine cause of error from SENDIO and correct.

An error was received from SENDIO running controller test.

Error returned from SENDIO for sparing run controller test.

Call your Hewlett-Packard Representative.

This is an invalid sector address.

Internal debug error. Not released. Invalid sector number from caller for run track test.

Call your Hewlett-Packard Representative.

An error was received from RENDEZVOUSIO sparing a sector.

Error returned from RENDEZVOUSIO for sparing spare sector.

Determine cause of error from RENDEZVOUSIO and correct.

An error was received from SENDIO sparing a sector.

Error returned from SENDIO for sparing spare sector.

Determine cause of error from SENDIO and correct.

This is an internal error in sector state.

Internal error. Error in sector state in bad sector table.

Retry the function (INSTALL, UPDATE, START or mount volume). Write over sector zero to bypass sparing on this volume and initialize it again. Call your Hewlett-Packard Representative.

An error was received from SENDIO sparing a track.

Error returned from SENDIO for sparing spare track.

Determine cause of error from SENDIO and correct.

A failure occurred from RENDEZVOUSIO skipping forward a tape file.

Error returned from RENDEZVOUSIO for skip tape file.

Determine cause of error from RENDEZVOUSIO and correct.

A failure occurred from SENDIO skipping forward a tape file.

Error returned from SENDIO for skip tape file.

Determine cause of error from SENDIO and correct.

A failure occurred from RENDEZVOUSIO rewinding tape.

Error returned from RENDEZVOUSIO for rewind tape.

Determine cause of error from RENDEZVOUSIO and correct.

A failure occurred from SENDIO rewinding tape.

Error returned from SENDIO for rewind tape.

Determine cause of error from SENDIO and correct.

A failure occurred from RENDEZVOUSIO unloading a tape.

Error returned from RENDEZVOUSIO for unload tape.

Determine cause of error from RENDEZVOUSIO and correct.

A failure occurred from SENDIO unloading a tape.

Error returned from SENDIO for unload tape.

Determine cause of error from SENDIO and correct.

A failure occurred from RENDEZVOUSIO reading file label from tape.

Error returned from RENDEZVOUSIO for read tape file label. Possible tape read error.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

A failure occurred from SENDIO reading file label from tape.

Error returned from SENDIO for read tape file label.

Determine cause of error from SENDIO and correct.

Not enough data was read from tape reading the file label.

Tape read expected 256 bytes and got less than 200 bytes. Possible tape read error or tape position error.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

A failure was received from RENDEZVOUSIO skipping backwards on tape.

Error returned from RENDEZVOUSIO for skip record back.

Determine cause of error from RENDEZVOUSIO and correct.

A failure was received from SENDIO skipping backwards on tape.

Error returned from SENDIO for skip record back.

Determine cause of error from SENDIO and correct.

A second NL.PUB.SYS was found on the boot tape.

A second NL.PUB.SYS file was found on the tape. Invalid tape format. File is identified by start number in tape file header.

Determine the cause of the extra NL.PUB.SYS file and correct. Remake the tape and redo the UPDATE or INSTALL.

Can not purge NL.PUB.SYS from disk.

Error returned from HPOPEN for create of NL.PUB.SYS. File is identified by start number in tape file header.

Determine cause of error from HPOPEN and correct.

A failure occurred from RENDEZVOUSIO reading user label block.

Error returned from RENDEZVOUSIO for read user label block of a system file.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

Length error reading user label block.

EOF read from tape while reading user label data. Invalid tape. Possible tape read error or tape position error.

Determine cause of error and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

A failure occurred from SENDIO reading user label block.

Error returned from SENDIO for read user label block.

Determine cause of error from SENDIO and correct.

An error occurred from FWRITELABEL writing user label.

Condition code error returned by FWRITE for user label block.

Determine cause of error from FWRITE and correct.

A failure occurred from RENDEZVOUSIO reading system file block from tape.

Error returned from RENDEZVOUSIO for read file block. Possible tape read error or tape position error.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

This is a premature EOF on tape reading the system file block.

An EOF was read from the tape before expected while reading system file data. Invalid tape. Possible tape read error or tape position error.

Determine cause of error and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

A failure was received from SENDIO reading system file block.

Error returned from SENDIO for system file block.

Determine cause of error from SENDIO and correct.

An error occurred from FWRITE on system file block.

Condition code error returned by FWRITE for file data block.

Determine cause of error from FWRITE and correct.

An error occurred from FCLOSE on system file.

Error from FCLOSE for system file.

Determine cause of error from FCLOSE and correct.

There is an error in the number of blocks on tape for system file; file length error.

Record count error from tape while reading system file data. Invalid tape. Possible tape read error or tape position error.

Determine cause of error and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

HPOPEN error occurred for DUMPAREA.

Error returned from HPOPEN for create of DUMPAREA.MPEXL.SYS.

Determine cause of error from HPOPEN and correct.

An error was received from FWRITE for DUMPAREA.

Condition code error returned by FWRITE for DUMPAREA.MPEXL.SYS.

Determine cause of error from FCLOSE and correct.

Error from FCLOSE for DUMPAREA.

Error from FCLOSE for DUMPAREA.MPEXL.SYS file.

Determine cause of error from FCLOSE and correct.

An error was received from HPOPEN for creating boot file.

Error returned from HPOPEN for create of a boot file.

Determine cause of error from HPOPEN and correct.

An error occurred on reading the tape boot file block.

Error returned from SENDIO for read file block from tape.

Determine cause of error from SENDIO and correct.

There was an error in the number of blocks on the tape for the boot file; file length error.

User label numbers in tape file label are incorrect. Invalid tape format. User labels are invalid for a boot file.

Determine cause of incorrect numbers and correct. Remake tape and retry the UPDATE or INSTALL.

An error was received from FWRITE on the boot file.

EOF read from tape before expected while reading boot file data. Invalid tape. Possible tape read error or tape position error.

Determine cause of error and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

Failure posting page 1 to disk.

Error from LOAD_POST writing to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

An error was received from FCLOSE of boot file.

Error from FCLOSE for a boot file.

Determine cause of error from FCLOSE and correct.

The procedure failed to add boot file to the LIF directory.

Error returned from ADD_NEXT_DIR_ENTRY for a boot file while attempting to add an entry to the LIF directory.

Determine cause of error from ADD_NEXT_DIR_ENTRY and correct.

There was an error in the number of blocks on tape for the boot file; file length error.

Record count error from tape while reading boot file data. Invalid tape. Possible tape read error or tape position error.

Determine cause of error and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from RENDEZVOUSIO reading first label from tape.

Error returned from RENDEZVOUSIO for read labels. First read from the tape. Possible tape read error or tape position error.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from SENDIO reading the first label from the tape.

Error returned from SENDIO for read labels. First read from the tape.

Determine cause of error from SENDIO and correct.

An error occurred on the first read; not enough data read.

Tape read expected 256 bytes and got less than 200 bytes. Possible tape read error or tape position error. First read from the tape. Reading labels.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from RENDEZVOUSIO reading the second label from the tape.

Error returned from RENDEZVOUSIO for read labels. Second read from the tape. Possible tape read error or tape position error.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from SENDIO reading the second label from the tape.

Error returned from SENDIO for read labels. Second read from the tape.

Determine cause of error from SENDIO and correct.

An error occurred on the second read; not enough data read.

Tape read expected 256 bytes and got less than 200 bytes. Possible tape read error or tape position error. Second read from the tape. Reading labels.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from RENDEZVOUSIO reading the LIF directory from the tape.

Error returned from RENDEZVOUSIO for read labels. Third read from the tape. Possible tape read error or tape position error.

Determine cause of error from RENDEZVOUSIO and correct. Clean tape drive and retry. Clean tape drive, remake tape and retry.

An error was received from SENDIO reading the LIF directory from the tape.

Error returned from SENDIO for read labels. Third read from the tape.

Determine cause of error from SENDIO and correct.

An error occurred reading the LIF directory from the tape; not enough data.

Tape read expected 256 bytes and got less than 200 bytes. Possible tape read error or tape position error. Third read from the tape. Reading labels.

Clean tape drive and retry. Clean tape drive, remake tape and retry.

This is not an MPE/iX boot tape; LIF label bad.

LIF label check failed. Not a valid boot tape.

Retry with a valid boot tape.

This is not an MPE/iX boot tape; MPE/iX label bad.

MPE/iX label check failed. Not a valid boot tape.

Retry with a valid boot tape.

An error was received from SENDIO writing disk page 1.

Error from LOAD_POST writing to sector zero and one of LDEV 1. First write to sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

An error was received from CREATE_OBJECT for first tape I/O buffer.

Error returned from CREATE_OBJECT for tape I/O buffer 1.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for a second tape I/O buffer.

Error returned from CREATE_OBJECT for tape I/O buffer 2.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for the tape LIF directory buffer.

Error returned from CREATE_OBJECT for tape LIF directory buffer.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for the disk LIF directory buffer.

Error returned from CREATE_OBJECT for disk LIF directory buffer.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for the tape LIF label buffer.

Error returned from CREATE_OBJECT for tape LIF label buffer.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from CREATE_OBJECT for the tape MPE/iX label.

Error returned from CREATE_OBJECT for tape MPE/iX label buffer.

Determine cause of error from CREATE_OBJECT and correct.

An error was received from HPOPEN for creating LIF directory.

Error from HPOPEN for LIFDIREC file.

Determine cause of error from HPOPEN and correct.

An error was received from FWRITE for the LIF directory.

Error from FWRITE for LIFDIREC file.

Determine cause of error from FWRITE and correct.

An error was received from FCLOSE, closing the LIF directory.

Error from FCLOSE for LIFDIREC file.

Determine cause of error from FCLOSE and correct.

An error occurred writing page 1 of the disk.

Error from LOAD_POST writing sector zero and one of LDEV 1.

Determine cause of error from LOAD_POST and correct.

An error was received from RENDEZVOUSIO reading the disk labels.

Error returned from RENDEZVOUSIO for read disk page 1, sector zero and one.

Determine cause of error from RENDEZVOUSIO and correct.

An error was received from SENDIO reading the disk labels.

Error returned from SENDIO for read disk page 1, sector zero and one.

Determine cause of error from SENDIO and correct.

This is not an MPE XL disk. UPDATE failed; INSTALL required.

Disk LDEV 1 is not a valid MPE/iX system master volume.

Replace with a valid MPE/iX system master and retry. Volume cannot be updated, INSTALL is required.

System Abort 345

Internal error. Invalid spare state. Debug code not released.

Call your Hewlett-Packard Representative.

A failure was received from CREATE_OBJECT for a semaphore to use to interlock the label.

Error returned from CREATE_OBJECT for volume label semaphore.

Determine cause of error from CREATE_OBJECT and correct.

A failure was received from CREATE_BAD_SECTOR_TABLE.

Error returned from CREATE_BAD_SECTOR_TABLE.

Determine cause of error from CREATE_BAD_SECTOR_TABLE and correct.

A failure was received from XM_INITXM.

Error from STARTGOLDENXID, transaction management routine.

Determine cause of error from STARTGOLDENXID and correct.

A failure was received from XM_INITXM.

Error from ENDGOLDENXID, transaction management routine.

Determine cause of error from ENDGOLDENXID and correct.