 |
» |
|
|
|
|  | |
- 1
- MESSAGE
LDEV #\ Cannot access serial disc using system buffers (SDERR 1)
- 2
- MESSAGE
LDEV #\ ATTACHIO failure - reading/writing disc label (SDERR 2)
- 3
- MESSAGE
LDEV #\ Fatal error - serial disc interface disabled (SDERR 3)
- 4
- MESSAGE
LDEV #\ Invalid length in WRITE'BUFFER (internal error) (SDERR 4)
- 5
- MESSAGE
LDEV #\ End of tape detected (SDERR 5)
- 6
- MESSAGE
LDEV #\ ATTACHIO failure - reading DTT/DSCT (SDERR 6)
- 7
- MESSAGE
LDEV #\ Pack overflow - probably ignored EOT (SDERR 7)
- 8
- MESSAGE
LDEV #\ ATTACHIO failure - writing DTT/DSCT (SDERR 8)
- 9
- MESSAGE
LDEV #\ Contig and non-contig data mixed in RECBUFF (SDERR 9)
- 10
- MESSAGE
LDEV #\ Can't call FINDSDISCGAP unless file is open (SDERR 10)
- 11
- MESSAGE
LDEV #\ FINDSDISCGAP - Block number must be > 0. (SDERR 11)
- 12
- MESSAGE
LDEV #\ ATTACHIO failure - assigning alternate tracks (SDERR 12)
- 13
- MESSAGE
LDEV #\ ATTACHIO failure - reading Gap Table (SDERR 13)
- 14
- MESSAGE
LDEV #\ Invalid control code (SDERR 14)
- 15
- MESSAGE
LDEV #\ ATTACHIO failure - writing Gap Table (SDERR 15)
- 16
- MESSAGE
LDEV #\ Attempted to write on protected drive (SDERR 16)
- 17
- MESSAGE
LDEV #\ Out of sync with Gap Table while reading (SDERR 17)
- 18
- MESSAGE
LDEV #\ Gap Table overflow - probably ignored EOT (SDERR 18)
- 19
- MESSAGE
LDEV #\ Too many EOFs for this disc (SDERR 19)
- 20
- MESSAGE
LDEV #\ No spare blocks available. (SDERR 20)
- 21
- MESSAGE
LDEV #\ Uninitialized media. (SDERR 21)
- 22
- MESSAGE
LDEV #\ Attempted to read past end of data (SDERR 22)
- 23
- MESSAGE
LDEV #\ Buffer pointer exceeds buffer (internal error) (SDERR 23)
- 24
- MESSAGE
LDEV #\ Attempted a Backspace File while at Load Point. (SDERR 24)
- 25
- MESSAGE
LDEV #\ Attempted to space backward at Load Point. (SDERR 25)
- 26
- MESSAGE
LDEV #\ Not a serial disc (disc label or internal error) (SDERR 26)
- 27
- MESSAGE
LDEV #\ Runaway serial disc (access beyond end of data) (SDERR 27)
- 28
- MESSAGE
LDEV #\ Access beyond end of Gap Table (internal error) (SDERR 28)
- 29
- MESSAGE
LDEV #\ ATTACHIO failure - writing data. (SDERR 29)
- 30
- MESSAGE
LDEV #\ Leading/trailing lengths don't match (corrupt disc) (SDERR 30)
- 31
- MESSAGE
LDEV #\ Tried to overfill SDISC buffer (internal error) (SDERR 31)
- 32
- MESSAGE
LDEV #\ ATTACHIO failure - reading data (SDERR 32)
- 33
- MESSAGE
LDEV #\ Corrupt Defective Track/Sector Table (SDERR 33)
- 34
- MESSAGE
LDEV #\ Not enough memory for data buffers. (SDERR 34)
- 35
- MESSAGE
LDEV #\ Device not allocated or LDTX corrupted (SDERR 35)
- 36
- MESSAGE
LDEV #\ Extra data segment too small for this device. (SDERR 36)
- 37
- MESSAGE
LDEV #\ Attempted to write past EOT without capability (SDERR 37)
- 38
- MESSAGE
LDEV #\ ATTACHIO failure - loading or unloading (SDERR 38)
- 39
- MESSAGE
LDEV #\ Request aborted externally. (SDERR 39)
- 40
- MESSAGE
LDEV #\ "Write" capability denied by operator (SDERR 40)
- 41
- MESSAGE
LDEV #\ System or device powerfail. (SDERR 41)
- 42
- MESSAGE
LDEV #\ ATTACHIO failure - setting IR on/off (SDERR 42)
- 43
- MESSAGE
LDEV #\ Required GPTMOD parameter missing. (SDERR 43)
|
