(NLIO WARN, NLIO ERR)

TERMINAL n IS SHUT.

PRINTER n IS SHUT.

TERMINAL n IS OPENED IN LANGUAGE n.

PRINTER n IS OPENED WITH LANGUAGE n.

TERMINAL n IS OPENED WITH LANGUAGE n, RECCONV.

TERMINAL n IS OPENED WITH LANGUAGE n, NORECCONV.

PRINTER n IS OPENED WITH LANGUAGE n, RECCONV.

PRINTER n IS OPENED WITH LANGUAGE n, NORECCONV.

LATIN MODE, WIDTH = n, SHAPE = n.

NONLATIN MODE, WIDTH = n, SHAPE = n.

TERMINAL n : LANGUAGE IS SET TO n.

PRINTER n : LANGUAGE IS SET TO n.

TERMINAL n : RECCONV IS SET.

TERMINAL n : NORECCONV IS SET.

PRINTER n : RECCONV IS SET.

PRINTER n : NORECCONV IS SET.

PRINTER n : LATIN MODE IS SET.

PRINTER n : NONLATIN MODE IS SET.

PRINTER n : WIDTH IS SET TO n.

PRINTER n : SHAPE IS SET TO n.

TERMINAL n IS ALREADY OPENED. (NLIO WARN 1200)

PRINTER n IS ALREADY OPENED. (NLIO WARN 1201)

You tried to OPEN a device which was already OPENed.

Use the SHOW command to check the status. Check the ldev.

TERMINAL n IS CONTROLLED BY OTHER PROCESS. (NLIO WARN 1202)

Same as message.

Re-try the same command.

TERMINAL n IS IN USE, SHUT PENDING. (NLIO WARN 1204)

Same as message.

No action required.

PRINTER n IS IN USE, SHUT PENDING. (NLIO WARN 1205)

Same as message.

No action required.

TERMINAL n HAS NOT BEEN OPENED YET. (NLIO WARN 1206)

You tried to SHUT a device which was not OPENed. Or, a device which you SHOWed was not OPENed.

Check the ldev if necessary

PRINTER n HAS NOT BEEN OPENED YET. (NLIO WARN 1207)

You tried to SHUT a device which was not OPENed. Or, a device which you SHOWed was not OPENed.

Check the ldev if necessary

NO TERMINAL/PRINTER HAS BEEN OPENED. (NLIO WARN 1208)

You tried to SHUT devices, or SHOWed the status when no device had been OPENed.

No action is required.

TERMINAL n IS SHUT PENDING. (NLIO WARN 1211)

Same as message.

No action required.

PRINTER n IS SHUT PENDING. (NLIO WARN 1212)

Same as message.

No action required.

"NLIODEF.PUB.SYS" FILE BEING ACCESSED. (NLIO WARN 1300)

UNKNOWN COMMAND WAS ENTERED. (NLIO ERR 2100)

Command name incorrect.

Re-enter the command. Use HELP to check the syntax.

TOO MANY PARAMETERS WERE ENTERED. (NLIO ERR 2101)

Same as message.

Re-enter the command using the correct syntax. Use HELP to check the syntax.

INVALID DELIMITER WAS ENTERED. (NLIO ERR 2102)

The second OPEN delimeter is incorrect.

Re-enter the command using the correct syntax. Use HELP to check the syntax.

LDEV CANNOT BE OMITTED FOR NON-INTERACTIVE STDIN. (NLIO ERR 2110)

Same as message.

Re-enter the command, specifying the ldev.

NO DEVICE IS DESIGNATED FOR SPECIFICED DEVICE. (NLIO ERR 2111)

The device or device class specified does not refer to a configured device.

Check the system configuration and re-enter the command, specifying the correct ldev.

SPECIFIED LDEV n IS NOT A TERMINAL OR PRINTER. (NLIO ERR 2113)

The specified ldev was other than a terminal or a printer.

Check the system configuration and re-enter the command, specifying the correct ldev.

SPECIFIED DEVICE CLASS IS NOT A TERMINAL OR PRINTER. (NLIO ERR 2114)

The specified device class does not apply to terminals or printers.`

Check the system configuration and re-enter the command, specifying the correct device class.

INVALID PARAMETER WAS ENTERED. (NLIO ERR 2115)

The specified ldev was other than a terminal or a printer.

Check the system configuration and re-enter the command, specifying the correct ldev.

TMUX TERMINAL WAS SPECIFIED. (NLIO ERR 2116)

INVALID LANGUAGE WAS ENTERED. (NLIO ERR 2120)

The input language ID was not a valid one.

Check the language ID and re-enter the command, specifying a correct language ID.

UNKNOWN LANGUAGE WAS ENTERED. (NLIO ERR 2121)

Unsupported language ID was entered. as the system default language.

Check the language ID and re-enter the command.

INVALID LANGUAGE IS USED. (NLIO ERR 2122)

Unsupported language ID was set as the user interface language set, or as the system default language.

Re-enter the command, specifying the correct language ID.

SPECIFIED LANGUAGE IS NOT CONFIGURED ON THE SYSTEM. (NLIO ERR 2123)

The specified language is not supported on the system.

Check and set the valid language, then re-enter the command.

INVALID WIDTH PARAMETER WAS ENTERED. (NLIO ERR 2130)

INVALID WIDTH VALUE WAS ENTERED. (NLIO ERR 2131)

INVALID SHAPE PARAMETER WAS ENTERED. (NLIO ERR 2140)

INVALID SHAPE VALUE WAS ENTERD. (NLIO ERR 2141)

UNKNOWN COMMAND FOR HELP. (NLIO ERR 2150)

You entered a command that HELP does not recognize.

Check the valid command names by entering the HELP command without any parameters. Then re-enter the HELP command using the correct parameter.

BOTH RECCONV AND NORECCONV PARAMETER WERE ENTERED. (NLIO ERR 2160)

BOTH LATIN AND NONLATIN PARAMETER WERE ENTERED. (NLIO ERR 2161)

REDUNDANT RECCONV PARAMETER. (NLIO ERR 2162)

REDUNDANT NORECCONV PARAMETER. (NLIO ERR 2163)

REDUNDANT LATIN PARAMETER. (NLIO ERR 2164)

REDUNDANT NONLATIN PARAMETER. (NLIO ERR 2165)

REDUNDANT WIDTH PARAMETER. (NLIO ERR 2166)

REDUNDANT SHAPE PARAMETER. (NLIO ERR 2167)

LANGUAGE WAS NOT ASIAN LANGUAGE. (NLIO ERR 2170)

LANGUAGE WAS NOT MEA LANGUAGE. (NLIO ERR 2171)

TERMINAL CANNOT BE OPENED WITH MEA LANGUAGE. (NLIO ERR 2180)

OP CAPABILITY IS REQUIRED. (NLIO ERR 2201) OP capability is required to specify an STDIN other than your own. You currently do not have OP capability. Check the ldev, or contact your System Manager to extend your capabilities.

MISSING MESSAGE CATALOG FILE = NLIOCAT.PUB.SYS. (NLIO ERR 2300) The message catalog for the NLIOUTIL program is missing. Contact your System Manager to locate the message catalog.

MISSING "NLIODEF.PUB.SYS FILE". (NLIO ERR 2301)