(Subsystem 113)

The operation was successful with retries.

An I/O was attempted and was successful, but retries were required.

None, unless an excessive number of retries occurred. If there are an excessive number, then changing the device or the media should be looked into. Call your Hewlett-Packard Representative for assistance.

Beginning of devices media encountered.

Beginning of media encountered when an I/O operation was issued.

None.

An attempt was made to lock a device or device manager which was already locked or unlock one not currently locked by this process.

Same as message content.

None.

Disk contains marginal (possibly unreliable) data.

Same as message content.

Call your Hewlett-Packard Representative.

A timeout occurred during a bind (software connect) operation.

A device did not respond during configuration.

Check to see if device is present.

Hardware error detected during a BIND operation.

A device did not respond during configuration.

Check to see if device is connected.

An end of file was detected.

Same as message content.

None.

The end of the media was detected.

Same as message content.

None.

The I/O completed successfully with some status available to be read.

Same as message content.

None.

The read was terminated by an alternate end of record (aeor).

Same as message content.

None.

Tape density requested is unknown or unsupported.

Same as message content.

Verify that the tape density is appropriate for the device.

A save-set mark was detected.

During an I/O operation involving the HPC1501A/HPC1511A cassette tape drive, a save-set mark (a type of index mark) was detected.

None.

Device adapter does not support asynchronous event notification (aen).

Device or device adaptor does not support asynchronous event notification.

None.

Trying to remotely load a tape device that is already loaded.

Same as message.

None.

Reservation conflict.

A device (or element in the device) cannot be accessed due to a reservation conflict.

Retry acquisition of the device later.

Incorrect hardware type.

The device or card is not of the proper type for the configured software.''

Verify that the configuration and involved devices are correct.

Device is unavailable.

When trying to do a remotely-waited FOPEN of a device, the device is not available.

Retry the request later or determine why the remote device is not responding.

File does not have a correct file code.

Same as message.

None.

Cannot open file.

Same as message.

None.

A tape device has reported that a tape tension loss condition has occurred.

Same as message.

None.

Special character passed in by previous FDEVICE control call.

Same as message.

None.

A device data format error has occurred after a device power failure.

Same as message.

None.

I/O read has been terminated by a subsystem BREAK.

Same as message.

None.

The procedure cannot back space beyond the beginning of the media.

Same as message content.

None.

The procedure cannot READ past the end of the volume.

Same as message content.

None.

The device does not support the requested density.

Same as message content.

Check file equation for incorrect density.

The device parity error count exceeded the maximum retry count.

Same as message content.

Call your Hewlett-Packard Representative.

The I/O completed successfully, and the last available device status should now be read.

Same as message content.

None.

The download of the firmware failed.

This could be caused by a number of problems. Most likely the device being downloaded to is not present, or a hardware failure has occurred.

Call your Hewlett-Packard Representative.

The device could not be cleared/reset.

This could be caused by a number of problems. Most likely the device is not present, or a hardware failure occurred.

Call your Hewlett-Packard Representative.

An incorrect hardware identification code was returned from device.

Device configured does not match device type.

Make sure device configured matches device type.

A transmission error occurred; send the data block again.

Same as message content.

Call your Hewlett-Packard Representative to examine link connection.

An error has occurred.

An I/O error has occurred. Device status is now available that should further explain the problem.

None.

An invalid internal software error occurred.

The operating system software module had an internal problem.

Call your Hewlett-Packard Representatiave.

A BREAK error occurred.

Same as message content.

None.

READ TIME was returned.

Same as message content.

None.

No Control Y process ID (PIN) is present.

Operating system software problem.

Call your Hewlett-Packard Representative.

The device is off-line.

Same as message content.

Place device online.

A RECEIVER OVERRUN occurred.

Operating system software problem.

Call your Hewlett-Packard Representative.

A READ TIMEOUT error occurred.

Device timeout occurred.

Call your Hewlett-Packard Representative.

A DATA TRANSMISSION error occurred.

Possible problem with media or link.

Call your Hewlett-Packard Representative.

A data parity error was detected.

A media defect or link error occurred.

Retry I/O operation. If problem persists, call your Hewlett-Packard Representative.

An invalid request code was detected by I/O MANAGER.

Operating system software error.

Call your Hewlett-Packard Representative.

The request was not started or completed due to an error condition.

Same as message content.

Determine if device is present or online. If so, call your Hewlett-Packard Representative.

Suspect data was encountered during I/O operation.

Same as message content.

Call your Hewlett-Packard Representative.

A generic hardware problem occurred.

Error condition occurred in using a device with which additional status is not available.

Call your Hewlett-Packard Representative.

The length of requested transfer is invalid for this device.

Same as message content.

Length of I/O is not supported by device. Change file equation to match device supported lengths.

The format, or order of command to a device is invalid.

Operating system software error.

Call your Hewlett-Packard Representative.

A CHANNEL TIMEOUT caused failure.

A device hardware or link failure was detected.

Call your Hewlett-Packard Representative.

The request failed due to a device time out.

Same as message content.

Verify that the device is connected properly and has power. Call your Hewlett-Packard Representative.

A LOWER LEVEL MANAGER error occurred; status is unknown or not available.

Operating system software error.

Call your Hewlett-Packard Representative.

Data was lost due to a transfer error.

Some sort of data transmission error.

Call your Hewlett-Packard Representative.

An invalid device address was requested.

Operating system software error.

Verify that the device configuration is correct. If it is, and problem persists, call your Hewlett-Packard Representative.

Unformatted media is being used.

Same as message content.

Format media and try operation over.

A parity, CRC, or other data type error was detected.

Possible hardware, media, or link failure.

Call your Hewlett-Packard Representative.

The device was physically reset or the I/O request was aborted by a reset request.

Same as message content.

None.

A device powering on condition was detected.

Same as message content.

Determine reason for device power failure.

A write operation to a read-only device was attempted.

Same as message content.

Determine process that attempted operation. Call your Hewlett-Packard Representative for assistance.

Operator attention is required, for example, printer is out of paper; tape needs next reel.

Same as message content.

Take action to correct condition. For example, put paper in the printer.

An unexpected end-of-file or resource occurred; for example, disk transfer hit the end of the volume or tape hit the end-of-tape mark.

Same as message content.

Call your Hewlett-Packard Representative.

The device is not ready or is not responding.

Same as message content.

Place device online.

The I/O MANAGER must be locked for this request and it is not.

Operating system or product software error.

Call your Hewlett-Packard Representative.

The I/O MANAGER has been locked by another module.

Possibly an operating system or product software error.

This may be a normal situation if a device diagnostic tool has obtained exclusive access to the device (e.g., tape device diagnostic tools such as REELDIAG and DIAG7978 do this). Check for this situation and if this is NOT the case, call your Hewlett-Packard Representative.

A memory request error occurred.

Operating system software error—Memory Manager returned an error.

Call your Hewlett-Packard Representative.

The procedure was unable to obtain memory necessary to continue operation.

Operating system software error—Memory Manager services of the operating system returned an error.

Call your Hewlett-Packard Representative.

An attempt to release memory failed.

Operating system software error—Memory Manager services of the operating system returned an error.

Call your Hewlett-Packard Representative.

Some resource was not released.

Operating system software problem.

Call your Hewlett-Packard Representative.

The request contained incorrect higher manager port number.

Operating system software problem.

Call your Hewlett-Packard Representative.

The DO_UNBIND operation failed.

Operating system software problem.

Call your Hewlett-Packard Representative.

The port number of lower level I/O MANAGER is incorrect.

Operating system software problem.

Call your Hewlett-Packard Representative.

A DO_UNBIND request was made to a nonexistent I/O MANAGER.

Operating system problem.

Call your Hewlett-Packard Representative.

The procedure cannot UNBIND because I/O is still pending.

Operating system or hardware failure.

Call your Hewlett-Packard Representative.

The BIND operation did not work or an UNBIND was requested of an I/O MANAGER that was not bound.

Operating system software problem.

Call your Hewlett-Packard Representative.

The BIND request failed; manager is already bound.

Operating system software problem.

Call your Hewlett-Packard Representative.

The BIND to lower manager failed.

Operating system software problem.

Call you Hewlett-Packard Representative.

Bad time on bus for this BIND or DO_BIND request.

Hardware failure occurred during configuration sequence.

Call your Hewlett-Packard Representative.

Bad critical response for this BIND or DO_BIND request.

Operating system software problem.

Call your Hewlett-Packard Representative.

Bad bandwidth for this BIND or DO_BIND request.

Operating system software problem.

Call your Hewlett-Packard Representative.

A bad hardware address was detected for a BIND or DO_BIND request.

Operating system software problem.

Call your Hewlett-Packard Representative.

A bad revision code was detected for a BIND or DO_BIND request.

Operating system software problem—version mismatch between modules and procedures.

Call your Hewlett-Packard Representative.

A bad meta tag was detected for a BIND or a DO_BIND request.

Operating system software problem occurred during configuration of device manager components.

Call your Hewlett-Packard Representative.

A bad subsystem identifier was detected for a BIND or a DO_BIND request.

Operating system problem occurred during configuration of device managers.

Call your Hewlett-Packard Representative.

An unclassified software problem occurred.

Operating system software problem.

Call your Hewlett-Packard Representative.

The state of the I/O MANAGER is in appropriate for this request.

Operating system software problem.

Call your Hewlett-Packard Representative.

The last available status was requested, but none is available yet.

Possible hardware failure.

Call your Hewlett-Packard Representative.

The requested operation cannot be understood by the I/O MANAGER.

Operating system software problem.

Call your Hewlett-Packard Representative.

The requested function/operation is not implemented by this I/O MANAGER.

Operating system software problem.

Call your Hewlett-Packard Representative.

A system power failure occurred. An I/O operation was aborted or not started.

Same as message content.

Determine why system power failure occurred.

An I/O operation was aborted by user.

Same as message content.

Determine why I/O was aborted.