 |
» |
|
|
|
Listed are the messages that are generated by the Link Trace
Formatter. They are displayed on the user terminal when running
NMDUMP. If you must submit an SR or call your HP representative, please
copy the error exactly as it appears on the terminal;
it will make determining the CAUSE of the problem easier. These
messages are not logged. The messages are listed in numerical order according to the
error number. MESSAGE: SUBSYSxxTRACEFORMAT
CM STUB ERROR (nnn,sss) FROM HPLOADNMPROC UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 995) | CAUSE: The CM
Stub could not load an NM WAN Trace Formatter routine for subsystem
"xx" from the system library XL.PUB.SYS. ACTION: Incorrect software
installation to run Native-Mode Trace Formatters. The SWITCH error
number is "nnn" and the subsystem reporting the
error is "sss". Call your HP representative. |
MESSAGE: SUBSYSTEM_xx_MENU
CM STUB ERROR (nnn,sss) FROM HPSWTONMNAME UNABLE TO CALL NM MENU ROUTINE (FMTERR 996) | CAUSE: The CM
Stub could not call the named NM WAN Trace Formatter options menu
routine for subsystem "xx" from the system library
XL.PUB.SYS. ACTION: Incorrect software
installation to run Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels. The SWITCH error number
is "nnn" and the subsystem reporting the error
is "sss". Call your HP representative. |
MESSAGE: SUBSYSxxTRACEFORMAT
CM STUB ERROR (nnn,sss) FROM HPSWTONMPLABEL UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 998) | CAUSE: The CM
stub successfully loaded the NM WAN Trace Formatter routine for
subsystem "xx" from the system library XL.PUB.SYS,
but could not call it. ACTION: Incorrect software
installation to run Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels or a bug in the NM WAN Trace
Formatter CM Stub. The SWITCH error number is "nnn"
and the subsystem reporting the error is "sss".
Call your HP representative. |
MESSAGE: SUBSYSxxTRACEFORMAT
CM STUB ERROR (nnn,sss) FROM HPSWTONMNAME UNABLE TO CALL NM TRACE FORMATTER ROUTINE (FMTERR 999) | CAUSE: The CM
Stub could not call the named NM WAN Trace Formatter routine for
subsystem "xx" in the system library XL.PUB.SYS. ACTION: Incorrect software
installation to run Native-Mode Trace Formatters. This could also
be CAUSEd by incorrect privilege levels. The SWITCH error number
is "nnn" and the subsystem reporting the error
is "sss". Call your HP representative. |
MESSAGE: ALL overrides
other selections entered at the same time | CAUSE: Among the
filter-set numbers you entered, you also specified the number for
ALL. This is a warning. ACTION: Check your input.
Unless you mistyped one of the other set-numbers, it does not make
sense to specify ALL along with other items, beCAUSE ALL would include
the other sets anyway. To retype your input after this warning you
must first return to the filter-set selection menu. |
MESSAGE: Warning:
Errors always print; for Errors only don't include other
sets | CAUSE: Among the
filter-set numbers you entered, you also specified the number for
ERRORS-ONLY. This is a warning. ACTION: Check your input.
Unless you mistyped one of the other set-numbers, it does not make
sense to specify ERRORS-ONLY along with other items, beCAUSE including
the other items would defeat the meaning of ERRORS-ONLY. To retype
your input after this warning you must first return to the filter-set
selection menu. |
MESSAGE: Input truncated
to 80 characters | CAUSE: The input
file to the user menu was given more than 80 characters
of input, but the menu can only accept 80. This is a warning. ACTION: If the extra characters
are just extra blanks, ignore this message or reduce the width of
the input file. But if the extra characters are non-blank, you must
edit the input file, finding a way to reduce the width of the input
data to no more than 80 characters. |
MESSAGE: Extra input
ignored | CAUSE: Only one
number was expected, but you entered more than one, and the extra
number(s) were ignored. This is a warning. ACTION: Check your input
and, if necessary, return to that prompt and retype the input. |
MESSAGE: Range error
at position shown; other values accepted if allowed | CAUSE: One of
the numbers you entered was out of range; a "^^"
indicator appears below the illegal number. The number entered was
probably much too large. ACTION: The bad value was
not accepted. You may press the Return key to keep the other values
on the same line, or else retype the entire input using only legal
values. |
MESSAGE: Syntax error
at position shown; other values accepted if allowed | CAUSE: Some of
the numbers on the input line contained illegal characters, or were
separated by illegal characters. Legal inputs are digits 0-9
and the question mark "?". Legal separators for
a list are the comma "," and the blank " ". ACTION: Retype the input. |
MESSAGE: Invalid
set number NN; reenter all or hit RETURN to keep others | CAUSE: One of
the filter-set numbers you selected is not one of the valid filter
sets for this formatter. ACTION: Check your input
against the available sets shown in the menu. You may press the
Return key to keep the other number(s) you entered on the same line,
or you may retype the entire input. You may also return to the main
menu and "set all options back to their default values." |
MESSAGE: Output limit
out of range; enter another number or hit RETURN | CAUSE: You have
selected a value which is less than the lower output limit or greater
than the upper output limit. ACTION: The value you selected
was not accepted. Reenter a value which is within the range shown
in the prompt. The prompt is meant as a reminder; values up to 4096
are also legal. |
MESSAGE: Invalid
option number NN ignored; others accepted | CAUSE: One of
the option numbers you selected at the main menu was not a valid
option number for this formatter. ACTION: The illegal option
number was ignored, but any other options on the same line were
executed. Check your input and retype if necessary. |
MESSAGE: Number of
inputs exceeds storage capacity, rest ignored | CAUSE: Bug in
Trace-Formatter numeric input processing. The formatter could not
process all the numbers entered by the user. ACTION: Check your input
and retype if necessary. If the problem continues to occur, submit
an HP Service Request form against the Trace Formatter, specifying
the input you tried and the subsystem you were trying to format.
A temporary solution might be to type fewer numbers. |
MESSAGE: CIERROR
NNNN while executing MPE command | CAUSE: The MPE
command you tried encountered an error. MPE returned error number
NNNN to the Formatter (MPE warnings are ignored). ACTION: Check your input.
If necessary, retype the MPE command. You may look up the Command
Interpreter error number in the NS 3000/iX Error Messages
Reference Manual. |
MESSAGE: MISSING
OPT EXECUTOR #NN; PLEASE SUBMIT HP SERVICE REQUEST | CAUSE: Bug in
Trace-Formatter option-execution processing. The formatter recognized
an option you typed, but could not find processing for the option. ACTION: Submit an HP Service
Request form against the Formatter, specifying what input you typed
and what subsystem you were trying to format. |
MESSAGE: MISSING
MESSAGE #NNNN | CAUSE: Bug in
Trace-Formatter error message processing. The explanatory text for
error number NNNN is missing from the formatter. ACTION: Submit an HP Service
Request form against the Formatter, specifying what input you typed
and what subsystem you were trying to format. |
|