 |
» |
|
|
|
A numerical list of validation error messages and actions
for each follows. Path: NMMGRpath —
A read error encountered while reading the data record (bad file).
(DTSERR=3) | Cause:
Either a hardware problem occurred or the data record is too long. Action:
Try to print the network management configuration file. Rebuild
the file from a copy of the sample file NMSAMP1.PUB.SYS.
If the problem persists, contact your Hewlett-Packard support representative. |
Path: NMMGRpath —
A write error encountered while updating the data record (bad file).
(DTSERR=4) | Cause:
Either a hardware problem occurred or the data record file is too
small. Action:
If the data record file has been compressed, it is impossible to
validate the file. Go to the UTILITY screen
and use the compression utility to make the file larger. Try to
validate the file. If it still fails, build the file from a copy
of the sample file NMSAMP1.PUB.SYS.
If the problem persists when verifying the new file, contact your
Hewlett-Packard support representative. |
Path: NMMGRpath —
The data record is empty (use Update Data function key). (DTSERR=5) | Cause:
The data record was not created for the NMMGRpath. Action:
Go back to the screen specified by the NMMGRpath
and update the screen. |
Path: NMMGRpath —
The same physical path is being used at LINK.linkname. (DTSERR=6) | Cause:
The physical path specified for this link is being used. Action:
Go back to the screen specified by the NMMGRpath
or go to the link screen specified by the linkname
and modify the physical path. |
Path: NMMGRpath —
The same station address is being used at LINK.linkname. (DTSERR=7) | Cause:
The IEEE 802.3 station address is already used. Each station address
must be unique. Action:
Go back to the screen specified by the NMMGRpath
or go to the screen specified by the linkname
and correct the station address. |
Path: NMMGRpath —
LINK.linkname is not defined. (DTSERR=8) | Cause:
The linkname specified on the DTS Configuration
screen is not defined; therefore, the link data record was not created. Action:
Verify the linkname on the Host Configuration
screen. If the link data record does not exist, update the DTS Configuration
screen. |
Path: NMMGRpath —
DTS.PROFPC.profilename is not defined. (DTSERR=9) | Cause:
The profilename on the screen specified by
the NMMGRpath is not defined; therefore, the
profile data record does not exist. Action:
Check that the profile name exists on the DTS Profile Selection
screen and, if it does, check that the data record for this profile
was created. |
Path: NMMGRpath —
The same station address or node name is being used at DTS.DTC.SELECT.DTCname.
(DTSERR=10) | Cause:
The station address or node name used on the screen specified by
the NMMGRpath is also used on the screen specified
by the path DTS.DTC.SELECT.DTCname
screen. Action:
Go to the screen specified by the NMMGRpath
or to the screen specified by the DTC name
and modify the station address or node name. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.
(DTSERR=11) | Cause:
The logical device (ldev) number is being used on the screen specified
by the NMMGRpath and on the DTS.DTC.SELECT.DTCname.CARD012
screen. Action:
Go to one of the two screens and change the ldev number. The ldev
number must be unique for each port. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.
(DTSERR=12) | Cause:
The same logical device (ldev) number is being used on the screen
specified by the NMMGRpath and on the DTS.DTC.SELECT.DTCname.CARD345. Action:
Go to one of the two screens and change the ldev number. The ldev
number must be unique for each port. |
Path: NMMGRpath —
LDEV #nnn is too big (must be <=4679). (DTSERR=14) | Cause:
The logical device (ldev) number is bigger than the allowed maximum
ldev number. Action:
Go to the screen specified by the NMMGRpath
and modify the ldev number. |
Path: NMMGRpath —
Too many LDEVs are being used (must be <=4649). (DTSERR=15) | Cause:
Too many logical device (ldev) numbers are being used. Action:
Review the screens that use ldevs and delete some ldev numbers.
The validation procedure allows a total of 4649 ldevs. |
Path: NMMGRpath —
Defined LINK.linkname is not being used. (DTSWARN=17) | Cause:
The defined linkname is not used by DTS or
the network interface. Action:
This is a warning only. No action is required. |
Path: NMMGRpath —
Too many links are being used (max. number allowed = 8).
(DTSERR=18) | Cause:
The link specified in the NMMGRpath cannot
be processed. Too many links are already defined. Action:
Go back to the DTS Configuration screen and delete the link specified
in the NMMGRpath. Delete all unused links so
that eight or less links are being used. |
Path: NMMGRpath —
Too many paths are being used (max. number allowed = 8).
(DTSERR=19) | Cause:
The link specified in the NMMGRpath cannot
be processed. Too many physical paths are already defined. Action:
Go back to the DTS Configuration screen and delete the link specified
in the NMMGRpath. Delete all unused links so
that eight or less links are being used. |
Path: NMMGRpath —
Too many DTCs are being used (max. number allowed = 120).
(DTSERR=20) | Cause:
The DTC specified in the NMMGRpath cannot be
processed. Too many DTCs are already configured. Action:
Go back to the DTC Configuration screen and delete the DTC specified
in the NMMGRpath. |
Path: NMMGRpath —
Too many nodes are being used (max. number allowed = 129).
(DTSERR=21) | Cause:
The DTC specified in the NMMGRpath cannot be
processed. Too many nodes are being used. Action:
Go back to the DTC Configuration screen and delete the DTC specified
in the NMMGRpath. |
Path: NMMGRpath —
Too many classes are being used (max. number allowed = 1000).
(DTSERR=22) | Cause:
The total number of classes exceeds the maximum allowed number. Action:
Delete class names so that no more than 1000 different class names
are associated with asynchronous devices. |
Path: NMMGRpath —
Too many profiles are being used (max. number allowed = 1024).
(DTSERR=23) | Cause:
The total number of defined profiles exceeds the maximum allowed. Action:
Delete profiles so that no more than 1024 are specified. |
No link is defined.
(DTSWARN=24) | Cause:
A link is not configured. Action:
Without a configured link, the network management configuration
file is useless. Return to the configuration screens and add a link,
making sure that all necessary data records are created. |
No DTC is defined.
(DTSWARN=25) | Cause:
A DTC is not configured. Action:
An action is not required if neither terminals, printers, nor both
are needed. If terminals and printers are required, return to the
configuration screens and add a DTC, making sure that all necessary
data records are created. |
Path: NMMGRpath —
LINK.linkname is shared with network interface. (DTSWARN=26) | Cause:
The same link is shared between the DTS and NS subsystem. A separate
link must exist for each of the two subsystems. Action:
Decide which of the two subsystems should use the existing link
and configure an additional link for the remaining subsystem. |
Path: NMMGRpath —
Modem type not supported. (DTSERR=30) | Cause:
The modem type specified on the DTS Terminal Profile screen is not
0, 1, or 2. A problem occurred while adding the ldev to a device
class. This could be caused because the class is used by a different
type of device such as a HPIB printer. Action:
Remove the class name from the profile for the ldev and delete and
re-add the ldev. Cross-validate the NMCONFIG.PUB.SYS
file with SYSGEN. Correct any problems found then restart DTS. |
Path: NMMGRpath —
Must supply a Physical Path. (DTSERR=32) | Cause:
A physical path was not specified in the Physical Path of LANIC
field. Action:
Go to the DTS Configuration screen and enter the appropriate physical
path. |
Path: NMMGRpath —
Duplicate profile class name profilename used. (DTSWARN=34) | Cause:
The same class name is used in several terminal profiles or the
same class name is used in several printer profiles. Action:
No action is required. Informational message only. |
Path: NMMGRpath —
Class name duplicated between printer and terminal profiles. (DTSERR=35) | Cause:
The same class name is used for both a terminal profile and a printer
profile. Action:
Remove the duplicate class name from the terminal profile or the
printer profile. |
Path: NMMGRpath —
Profile profilename specified for non-nailed terminals is of PRINTER
type. (DTSERR=36) | Cause:
A printer profile is specified where only a terminal profile is
allowed. Action:
Change the printer profile to be a terminal profile. |
Path: NMMGRpath —
Profile profilename specified for non-nailed PAD terminals is of
PRINTER type. (DTSERR=37) | Cause:
A printer profile is specified where only a terminal profile is
allowed. Action:
Change the printer profile to be a terminal profile. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD0.
(DTSERR=38) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD1.
(DTSERR=39) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD2.
(DTSERR=40) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD3.
(DTSERR=41) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD4.
(DTSERR=42) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD5.
(DTSERR=43) | Cause:
A PAD name is used more than once. Action:
Remove all of the duplicate references to the PAD name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD0.
(DTSERR=44) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD1.
(DTSERR=45) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.PAD2.
(DTSERR=46) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD3.
(DTSERR=47) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD4.
(DTSERR=48) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.PAD5.
(DTSERR=49) | Cause:
The same logical device (ldev) number is used more than once. Action:
Remove the duplicate ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD012.
(DTSERR=50) | Cause:
The logical device (ldev) number is used more than once in the CARD012
configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTCPC.SELECT.DTCname.CARD345.
(DTSERR=51) | Cause:
The logical device (ldev) number is used more than once in the CARD345
configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same node name is being used at linkname. (DTSERR=52) | Cause:
The same node name is used more than once. Action:
Remove the duplicate reference to the node name. |
Path: NMMGRpath —
Blank NODENAME. (DTSERR=53) | Cause:
A host node name is not specified on the screen specified in the
path. Action:
Enter a host node name on the screen specified in the path. |
Path: NMMGRpath —
The profile for LDEV #nnn, profilename, is not defined. (DTSERR=54) | Cause:
An incorrect profile name was used for the logical device (ldev). Action:
Verify the profile name for the logical device in the DTS Profile
Selection screen. |
Path: NMMGRpath —
Too many ldevs are configured using device class name devicename
(max allowed num = 255). (DTSERR=55) | Cause:
Too many logical devices are configured under the specified device
class name. The maximum allowed is 255. Action:
Reduce the number of logical devices configured under the specified
device class name. |
Path: NMMGRpath —
Profile profilename specified for non-nailed PAD terminals is of
PRINTER or PADPRINT type. (DTSERR=57) | Cause:
A printer or PAD printer profile is specified where only a terminal
or pad terminal profile is allowed. Action:
Change the printer profile to be a terminal profile. |
Path: NMMGRpath —
The profile for LDEV #nnn, profilename, is of PADTERM or PADPRINT
type. (DTSERR=58) | Cause:
A PAD terminal or PAD printer profile is specified where only a
terminal or printer profile is allowed. Action:
Change the PAD terminal or PAD printer profile to be a terminal
or printer profile. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD0.
(DTSERR=59) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD1.
(DTSERR=60) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD2.
(DTSERR=61) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD3.
(DTSERR=62) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD4.
(DTSERR=63) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
PAD device name for LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD5.
(DTSERR=64) | Cause:
The same PAD device name is used more than once in the configuration. Action:
Remove any duplicate references to the PAD device name. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD0.
(DTSERR=65) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD1.
(DTSERR=66) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD012.PAD2.
(DTSERR=67) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD3.
(DTSERR=68) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD4.
(DTSERR=69) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
The same LDEV #nnn is being used at DTS.DTC.SELECT.DTCname.CARD345.PAD5.
(DTSERR=70) | Cause:
The logical device (ldev) number is used more than once in the configuration. Action:
Remove any duplicate references to the ldev number. |
Path: NMMGRpath —
Modem behavior DCE high for LDEV #nnn, defined in Profile profilename,
is not supported on DTC16 and DTC48. (DTSERR=71) | Cause:
DCE high modem behavior is not supported for devices on a DTC 16
or DTC 48. DCE high is being specified for LDEV #nnn,
which is on a DTC 16 or DTC 48. Action:
Modify the modem behavior to one that is supported for the DTC,
or make sure you have specified the right DTC type (not a DTC 16
or DTC 48) for the device with LDEV #nnn. |
Path: NMMGRpath —
Hardware handshaking for LDEV #nnn, defined in Profile profilename,
is not supported on DTC16 and DTC48. (DTSERR=72) | Cause:
Hardware handshaking is not supported for devices on a DTC 16
or DTC 48. Hardware handshaking is being specified for
LDEV #nnn, which is on a DTC 16 or
DTC 48. Action:
Make sure you have specified the right DTC type (not a DTC 16
or DTC 48), or if you are configuring ports on a DTC 16
or DTC 48, do not use a profile that specifies hardware
handshaking. |
Path: NMMGRpath —
Modem behavior is not supported. (DTSERR=73) | Cause:
An invalid modem behavior has been specified. Valid modem behavior
values are: 0, 1, 2, or 3. The configuration file may be corrupt. Action:
Modify the modem behavior specified on the Terminal Profile or Printer
Profile screens to a valid value. |
Path: NMMGRpath —
Invalid AFCP timer selection. (DTSERR=74) | Cause:
You have specified an invalid AFCP timer selection. Action:
Go to the Tune DTC — Timer Selection Screen and choose
a value from 1 to 6 for an AFCP timer selection. |
Path: NMMGRpath —
Invalid Management timer selection. (DTSERR=75) | Cause:
You have specified an invalid management timer selection. Action:
Go to the Tune DTC — Timer Selection Screen and choose
a value of 1 or 2 for a management timer selection. |
Path: NMMGRpath —
Baud rate 38400 for LDEV #nnn, defined in Profile profilename, is
not supported on DTC16 and DTC48. (DTSERR=76) | Cause:
You have used a profile that specified a baud rate of 38400 for
a device that is connected to a DTC 16 or DTC 48. Action:
Make sure you specified the right DTC type (not a DTC 16 or DTC
48), or do not use this profile for the port with LDEV #nnn. |
Internal error. Failed
to get memory. (DTSERR=77) | Cause:
The operating system was unable to allocate the memory needed to
store data used during validation. Action:
Build a new file from the sample file NMSAMP1.PUB.SYS.
Try to validate the file. If the same error message appears when
verifying the new file, contact your Hewlett-Packard support representative. |
Path: NMMGRpath —
Back-to-Back, currently configured on LDEV #nnn, must use LDEV #
-1. (DTSERR=78) | Cause:
A profile of type HOST
has been configured on a DTC port and the ldev specified is not
-l. Action:
Ports using HOST
profiles are for back-to-back and must have an ldev of -l. Go to
the screen specified in NMMGRpath and change
the ldev to -l or use a different profile that is not of type HOST. |
Path: NMMGRpath —
X.25 card is not allowed in slot s. (DTSERR=79) | Cause:
An X.25 card has been configured in a slot that is not allowed for
the DTC type. Action:
Go to the DTC specified in the NMMGRpath and
delete the X.25 card from the slot number s. |
Path: NMMGRpath —
Too many X.25 cards are configured. Maximum is 3. (DTSERR=80) | Cause:
To many X.25 cards have been configured in the DTC specified in
NMMGRpath. Action:
Go to the DTC specified in the NMMGRpath and
delete one or more X.25 cards. |
Path: NMMGRpath —
LAN cardtype is not allowed on DTC16 or DTC48. (DTSERR=81) | Cause:
The configuration for the DTC specified in NMMGRpath
has a cardtype of "L" configured. This is not
allowed for DTC 16 or DTC 48. Action:
Go to the DTC Configuration screen specified in NMMGRpath
and enter the correct cardtypes. |
Path: NMMGRpath —
Too many LAN cards configured. Only one is allowed. (DTSERR=82) | Cause:
The configuration for the DTC specified in NMMGRpath
has more than one LAN card specified in the cardtypes. Action:
Go to the DTC Configuration screen specified in NMMGRpath
and change the extra "L" cardtypes to another
valid type. |
Path: NMMGRpath —
Unknown cardtype specified for card c. (DTSERR=83) | Cause:
The configuration for the DTC specified in NMMGRpath
has been corrupted. Action:
Delete the DTC specified in NMMGRpath and re-enter
the data for this DTC. |
Path: NMMGRpath —
Cardtype for card c does not match DTC card configuration. (DTSERR=84) | Cause:
The configuration for the DTC specified in NMMGRpath
has been corrupted. Action:
Delete the DTC specified in NMMGRpath and re-enter
the data for this DTC. |
Path: NMMGRpath —
Cardtype configured on card c not allowed on dtctype. (DTSERR=85) | Cause:
The configuration for the DTC specified in NMMGRpath
has been corrupted. Action:
Delete the DTC specified in NMMGRpath and re-enter
the data for this DTC. |
Path: NMMGRpath —
Ldev #nnn> is not valid (must be >= -l and <=4679). (DTSERR=86) | Cause:
The logical device (ldev) number is outside the allowed range. Action:
Go to the screen specified in NMMGRpath and
modify the ldev number. |
Path: NMMGRpath —
Ldev of -l is not allowed with printer or terminal profile. (DTSERR=87) | Cause:
An ldev number of -l has been specified on a port that has a profile
configured that is of type terminal or printer. Action:
Go to the screen specified in NMMGRpath and
change the ldev or specify a profile that is a type HOST. |
Path: NMMGRpath —
Profile for ldev #nnn, <profname>, is of HOST type. (DTSERR=88) | Cause:
Profile <profname> is of type HOST
and has been configured on a DTC port where ldev specified is not
-l. Action:
Ports using HOST
profiles are for back-to-back and must have an ldev of -l. Go to
the screen specified in NMMGRpath and change
the ldev to -l or use a different profile that is not of type HOST. |
Path: NMMGRpath —
Too few non-nailed ldevs available above TIO start ldev. (DTSERR=89) | Cause:
There are not enough ldevs available above the TIO start ldev number
to configure the number of ldev specified. Action:
Lower the number of TIO non-nailed ldevs or delete all TIO non-nailed
ldevs and specify a lower starting ldev number. Then add the desired
number of ldevs. |
Path: NMMGRpath —
Too few non-nailed ldevs available above PAD start ldev. (DTSERR=90) | Cause:
There are not enough ldevs available above the PAD start ldev number
to configure the number of ldev specified. Action:
Lower the number of PAD non-nailed ldevs or delete all PAD non-nailed
ldevs and specify a lower starting ldev number. Then add the desired
number of ldevs. |
Path: NMMGRpath —
Attached device for LDEV #nnn, defined in Profile <profname>,
is not supported on DTC16 and DTC48. (DTSERR=92) | Cause:
Modem devices configured (either US inout modem or European inout
modem) are not supported on DTC16 or DTC48. Action:
Go to DTC specified in NMMGRpath and change
the modem type to required modem type other than US inout or European
inout. |
Path: NMMGRpath —
Eight bit with parity for LDEV #nnn, defined in Profile <profname>,
is not supported on DTC16 and DTC48. (DTSERR=93) | Cause:
Eight bit data length with odd/even parity ("8odd"
or "8eve") feature is not supported
on DTC16 or DTC48. Action:
Go to DTC specified in NMMGRpath and change
the entry for the parity to the required value other than "8eve"
or "8odd". |
Path: NMMGRpath —
Two stop bits for LDEV #nnn, defined in Profile <profname>,
is not supported on DTC16 and DTC48. (DTSERR=94) | Cause:
Two stops bits feature is not supported on DTC16 or DTC48. Action:
Go to DTC specified in NMMGRpath and change
the entry for the number of stop bits to one. |
Path: NMMGRpath —
Binary port config for LDEV #nnn, defined in Profile <profname>,
is not supported on DTC16 and DTC48. (DTSERR=95) | Cause:
The feature for forcing data length and parity when binary mode
is selected is not supported on DTC16 or DTC48. Action:
Go to DTC specified in NMMGRpath and change
the entry for the binary port config field to "N". |
|