Displays the status of a specific SNA node.
Syntax |
 |
SNACONTROL STATUS;NODE=NodeName
[;LUNAME[=LUName]]
[;NAU][NAUNumber]]
[;LFSID[=odai,sid]]
[;STATUS=ALL ]
[ ACTIVE ]
[ INACTIVE]
[ PENDING ]
[ RESET ]
[;SESSTYPE=ALL ]
[ SSCP ]
[ LU ]
[ LU_DEP]
[ LU_IND]
[;NCB]
[;HSCB]
[;ROUTE]
[;LURECORD]
[;LINK[=A[LL] ] ]]
[ [=L[INK[STATE]] ]]
[ [=C[ONF[IGURATION]]]]
[ [=S[TAT[ISTICS]] ]]
[ [=D[IAG[STATS]] ]]
[ [=R[ESET] ]]
|
Use |
|
SNACONTROL STATUS can be issued from a session, a job,
a program, or in break. Pressing BREAK has no effect on this
command.
Parameters |
|
- NodeName
Conditionally required. The name< of the configured SNA node whose status you want displayed. The name can be up to eight alphanumeric characters long; the first character must be alphabetic.
If only one SNA node is active, this parameter is optional: If you do not include it, the active node's status is displayed. If more than one node is active, this parameter is required: If you do not include it, a list of all configured SNA nodes is displayed, but no status is displayed; you can then reissue this command with the appropriate node name.
- LUName
The name of the LU whose session status you want displayed. The
name can be up to eight alphanumeric characters long. The first character
must be alphabetic. If this parameter is specified, neither the NAU
nor LFSID parameters can be specified. Specifying this parameter
without an LU name causes the sessions to be displayed in alphabetical
order.
- NAU
The NAU number of the dependent session whose status you want to
display. The NAU number must be a decimal number between 0 and 255. If
this parameter is specified, neither the LUNAME nor LFSID parameters
can be specified. Specifying this parameter without an NAU number
causes the sessions to be displayed in numerical order.
- LFSID
The LFSID number of the independent session whose status you want to
display. The LFSID must consist of the ODAI followed by the SID,
with a comma as a separator. The ODAI must be either 0 or 1. The
SID must be a hex number between $0000 and $FFFE. If this parameter
is specified, neither the LUNAME nor NAU parameters can be specified. Specifying
this parameter without an LFSID number causes the sessions to be displayed
in numerical order.
- STATUS
Specifies the status of the sessions that are to be displayed. Possible
values for this parameter are ALL (all sessions), ACTIVE
(only active sessions), INACTIVE (only inactive sessions),
PENDING (only sessions that are pending activation or pending
reset), and RESET (only reset sessions).
- SESSTYPE
Specifies the session type of the sessions that are to be displayed. Possible
values for this parameter are ALL (all sessions), SSCP
(only PU-SSCP and LU-SSCP sessions), LU (only LU-LU dependent
and LU-LU independent sessions), LU_DEP (only LU-LU dependent
sessions), and LU_IND (only LU-LU dependent sessions).
- NCB
Specifies that the node's Node Control Block (NCB) is to be displayed. This
parameter is for Hewlett-Packard debugging purposes, and should be
used only under HP recommendation.
- HSCB
Specifies that the session's Half Session Control Block (HSCB) is to be displayed.
This parameter is for Hewlett-Packard debugging purposes, and should be used only under HP recommendation.
- ROUTE
Specifies that the session's Routing Table entry (packets received) is to be displayed.
This parameter is for Hewlett-Packard debugging purposes, and should be used only under HP recommendation.
- LURECORD
Specifies that the session's LU record is to be displayed.
This parameter is for Hewlett-Packard debugging purposes, and should be used only under HP recommendation.
- LINK
This is the same as specifying the ALL
link status parameter (described below).
- ALL
All of the status information for the link is displayed:
Link state status (see the LINKSTATE parameter description)
Link configuration data (see
the CONFIGURATION parameter description)
Link statistics
(see the STATISTICS parameter description)
Note that if no other link status parameter (LINKSTATE,
CONFIGURATION, STATISTICS, DIAGSTATS,
and RESET) is specified, this parameter (ALL)
is the default.
- LINKSTATE
State status information for the link is displayed:
SDLC:
X.25:
Token Ring:
This information is explained in more detail after the
examples later in this command description.
- CONFIGURATION
Configuration data for the link is displayed:
SDLC:
X.25:
Network interface (NI) name
Virtual circuit (VC) type
For a permanent virtual circuit (PVC):
For a switched virtual circuit (SVC):
Token Ring:
This information is explained in more detail after the
examples later in this command description.
- STATISTICS
Statistics for the link, for both inbound (sent) and outbound
(received) paths of the link, are displayed:
SDLC:
Oversized frames received
X.25:
Total bytes sent and received
Data bytes sent and received
Control bytes sent and received
Total packets sent and received
Data packets sent and received
Control packets sent and received
Token Ring:
Number of frames sent and received without errors
Number of bytes sent and received without errors
Number of frames not successfully transmitted
Number of frames received with errors
This information is explained in more detail after the
examples later in this command description.
- DIAGSTATS
All of the status information for the link is displayed:
Link state status (see the LINKSTATE
parameter description)
Link configuration data (see
the CONFIGURATION parameter description)
Link statistics (see the STATISTICS parameter description)
This parameter is for Hewlett-Packard debugging purposes,
and should be used only under HP recommendation.
- RESET
Link statistics are gathered from
the time the link is started. This parameter resets those statistics
to 0. To gather link statistics for a specific time period, issue
this command (SNACONTROL STATUS) with this parameter (RESET)
specified, to reset the statistics to 0. Once the statistics have
been gathered for the desired time period, issue this command again,
with the ALL or STATISTICS parameter specified.
Description |
|
You can use SNACONTROL STATUS to display the status of
sessions on a specific SNA node. The status of a session can be displayed
only when a Half Session Control Block (HSCB) has been created for
that session by SNA Transport. An HSCB is created when an SNA service
initiates a session with SNA Transport, or if tracing is turned on
for a session. The status of a session is not displayed if an LU
has only been configured.
SDLC Link-Level Status Information |
|
An example of an SDLC link-level status display is given below, and the terminology used is described after the example. Note that when link-level status information is displayed, the corresponding session-level status information is also displayed. (Since the session-level status terminology is described later under "Session-Level Status Information," it is not described here.)
Example
If an SDLC link is being used, typing
SNACONTROL STATUS;NODE=IBMNODE;LINK=ALL
where IBMNODE is already active could generate this display:
Linkname: IBMNODE Linktype: SNA/SDLC Linkstate:
CONNECTING LEVEL 1
Physical Path 40
Phone Number
Auto Dial 0 Cable Type None
Station ID C1 Buffer Size 265 bytes
XID XID6789012 Connect Timeout 900 sec
Receive Timeout 180 sec Local Timeout 30 sec
Error Retries 7 Transmission Speed 9600 bps
Connect Duration 135:09:19 Tracing OFF
Data Bytes Sent 0 Data Bytes Rcvd 0
Overhead Bytes Sent 0 Overhead Bytes Rcvd 0
Total Frames Sent 0 Total Frames Rcvd 0
Data Frames Sent 0 Data Frames Rcvd 0
Bytes Retransmitted 0 Oversized Frames Rcvd 0
Frames Retransmitted 0 Aborted Frames Rcvd 0
DSR Losses 0 Receive Overruns 0
CTS Losses Unexpected 0 CRC Errors 0
DCD Carrier Losses 0 Statistics Resets 0
NAME TYPE NAU STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
XPORTPU PU_SSCP 0 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 1 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 2 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 3 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 4 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 5 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 6 RESET MANAGER.SYS OFF
PFA2 DEP_LU 2 PEND_ACT_R PITEST.PUT21R40 NMTC0090.PUB.SYS
PFA3 DEP_LU 3 ACTIVE PITEST.PU2140 OFF
PFA4 DEP_LU 4 PEND_RST_R PITEST.PU2140 OFF
PFA5 DEP_LU 5 PEND_SON PITEST.PU2140 OFF
PFACLASS DEP_LU 1 RESET PITEST.PU2140 OFF
NAME TYPE LFSID STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
INDLU1 IND_LU 1,0200 PEND_ACT_L PITEST.PUT21R40 OFF
INDLU2 IND_LU 1,0201 PEND_RST_L PITEST.PUT21R40 OFF
INDLU3 IND_LU 1,0202 PEND_RST_N PITEST.PUT21R40 OFF
INDLU4 IND_LU ------ RESET PITEST.PUT21R40 OFF
|
Terminology
The linkname is the same as the node name.
The linktype is "SNA/SDLC".
The linkstate is one of the following:
NOT CONNECTED = The connection
is closed.
CONNECTED LEVEL 1 = A level
1 connection has been established.
CONNECTED LEVEL 2 = A level
2 connection has been established.
CONNECTING LEVEL 1 = A level
1 connection is in progress.
CONNECTING LEVEL 2 = A level
2 connection is in progress.
DISCONNECTING LVL 1 = A level
1 disconnection is in progress.
DISCONNECTING LVL 2 = A
level 2 disconnection is in progress.
ERROR = The SDLC link driver has detected
a link error.
The physical path is the address of the PSI.
The phone number is the number the link dials into, if an auto-dial modem is being used.
Auto dial is "0" if a leased line, a manual-dial modem, or no modem is being used; "1" if an auto-dial modem is being used.
The station ID is the HP 3000's link station identifier to the remote system's communications controller.
The XID is the station identification that is transmitted to the remote system whenever the HP 3000 receives an Exchange Station Identification (XID) request frame.
The receive timeout is the number of seconds the link-level software will wait for the remote system poll before closing the line.
Error retries is the maximum number of times the SDLC link manager will retry after errors or timeouts before setting the line to idle.
The cable type is one of the following:
The buffer size is the longest frame (in bytes) that the PSI is allowed to receive.
The connect timeout is the number of seconds the SDLC link driver will wait for a link Set Normal Response Mode (SNRM) command after telling the PSI to enable the Data Terminal Ready (DTR) signal, before closing the line.
The local timeout is the number of seconds the SDLC link driver will wait for PSI card activity before reporting a PSI failure.
The transmission speed is the transmission speed (in bits per second) of the line being used by the link if a modem is not being used. If a modem is being used, the modem determines the speed.
The connect duration is how long a level 2 connection has been maintained.
Data bytes sent is the total number of bytes that have been sent in the information field of an Information (I) frame.
Overhead bytes sent is the total number of SDLC bytes that have been sent. The total includes flags and Frame Check Sequence (FCS) bytes.
Total frames sent is the total number of frames that have been sent.
Data frames sent is the total number of Information (I) frames that have been sent.
Bytes retransmitted is the number of non-SDLC data bytes that have been retransmitted.
Frames retransmitted is the number of frames that have been retransmitted because the frame was not acknowledged.
DSR losses is the total number of times the Data Set Ready (DSR) signal has dropped unexpectedly.
CTS losses unexpected is the total number of times the Clear To Send (CTS) signal has dropped unexpectedly.
DCD carrier losses is the total number of times the Data Carrier Detector (DCD) signal has dropped unexpectedly.
Tracing is "ON" if link-level tracing is on, or "OFF" if the tracing is off.
Data bytes rcvd is the total number of bytes that have been received in the information field of an Information (I) frame.
Overhead bytes rcvd is the total number of SDLC bytes that have been received. The total includes flags and Frame Check Sequence (FCS) bytes.
Total frames rcvd is the total number of frames that have been received.
Data frames rcvd< is the total number of Information (I) frames that have been received.
Oversized frames rcvd is the total number of received frames that exceed the maximum configured frame size.
Aborted frames rcvd is the total number of aborted frames that were received.
Receive overruns is the total number of received frames that contained no control bytes.
CRC errors is the total number of received frames that contained a Cyclical Redundancy Check (CRC) error.
Statistics resets is the total number of times the statistics have been cleared.
X.25 Link-Level Status Information |
|
Two examples of X.25 link-level status displays are given below, and the terminology used is described after the examples. Note that when link-level status information is displayed, the corresponding session-level status information is also displayed. (Since the session-level status terminology is described later under "Session-Level Status Information," it is not described here.)
Example 1
If an X.25 link is being used, typing
SNACONTROL STATUS;NODE=IBMNODE;LINK=ALL
where IBMNODE is already active, and a permanent virtual circuit (PVC) is being used, could generate this display:
LINKNAME : IBMNODE LINKTYPE : SNA X.25 LINKSTATE:
SNA CONNECTED
TRACING : ON TRACEFILE: TRACE.PUB.SYS
LINK CONFIGURATION DATA:
NINAME : X25NI
INACTIVITY TIMEOUT: 0
VC TYPE : PVC
PVC NUMBER : 10
LINK STATISTICS:
SENT RECEIVED
- - - - - -
TOTAL BYTES : 8100 TOTAL BYTES : 8100
DATA BYTES : 8080 DATA BYTES : 8080
CONTROL BYTES : 20 CONTROL TYPES : 20
TOTAL PACKETS : 10 TOTAL PACKETS : 10
DATA PACKETS : 8 DATA PACKETS : 8
CONTROL PACKETS: 2 CONTROL PACKETS: 2
NAME TYPE NAU STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
XPORTPU PU_SSCP 0 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 1 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 2 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 3 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 4 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 5 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 6 RESET MANAGER.SYS OFF
PFA2 DEP_LU 2 PEND_ACT_R PITEST.PUT21R40 NMTC0090.PUB.SYS
PFA3 DEP_LU 3 ACTIVE PITEST.PU2140 OFF
PFA4 DEP_LU 4 PEND_RST_R PITEST.PU2140 OFF
PFA5 DEP_LU 5 PEND_SON PITEST.PU2140 OFF
PFACLASS DEP_LU 1 RESET PITEST.PU2140 OFF
NAME TYPE LFSID STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
INDLU1 IND_LU 1,0200 PEND_ACT_L PITEST.PUT21R40 OFF
INDLU2 IND_LU 1,0201 PEND_RST_L PITEST.PUT21R40 OFF
INDLU3 IND_LU 1,0202 PEND_RST_N PITEST.PUT21R40 OFF
INDLU4 IND_LU ------ RESET PITEST.PUT21R40 OFF
|
Example 2
If an X.25 link is being used, typing
SNACONTROL STATUS;NODE=IBMNODE;LINK=ALL
where IBMNODE is already active, and a switched virtual circuit (SVC) is being used, could generate this display:
LINKNAME : IBMNODE LINKTYPE : SNA X.25 LINKSTATE:
SNA CONNECTED
TRACING : ON TRACEFILE: TRACE.PUB.SYS
LINK CONFIGURATION DATA:
NINAME : X25NI CALL DIRECTION : OUT
INACTIVITY TIMEOUT: 0 MAX CALL RETRIES: 10
@COMPUTERTEXTW = VC TYPE : SVC CALL
RETRY DELAY: 60
REMOTE ADDRESS : FFFFFFFFFFFFFF CALL RETRY COUNT: 0
LINK STATISTICS:
SENT RECEIVED
- - - - - -
TOTAL BYTES : 8100 TOTAL BYTES : 8100
DATA BYTES : 8080 DATA BYTES : 8080
CONTROL BYTES : 20 CONTROL TYPES : 20
TOTAL PACKETS : 10 TOTAL PACKETS : 10
DATA PACKETS : 8 DATA PACKETS : 8
CONTROL PACKETS: 2 CONTROL PACKETS: 2
NAME TYPE NAU STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
XPORTPU PU_SSCP 0 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 1 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 2 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 3 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 4 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 5 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 6 RESET MANAGER.SYS OFF
PFA2 DEP_LU 2 PEND_ACT_R PITEST.PUT21R40 NMTC0090.PUB.SYS
PFA3 DEP_LU 3 ACTIVE PITEST.PU2140 OFF
PFA4 DEP_LU 4 PEND_RST_R PITEST.PU2140 OFF
PFA5 DEP_LU 5 PEND_SON PITEST.PU2140 OFF
PFACLASS DEP_LU 1 RESET PITEST.PU2140 OFF
NAME TYPE LFSID STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
INDLU1 IND_LU 1,0200 PEND_ACT_L PITEST.PUT21R40 OFF
INDLU2 IND_LU 1,0201 PEND_RST_L PITEST.PUT21R40 OFF
INDLU3 IND_LU 1,0202 PEND_RST_N PITEST.PUT21R40 OFF
INDLU4 IND_LU ------ RESET PITEST.PUT21R40 OFF
|
Terminology
The linkname is the same as the node name.
The linktype is "SNA X.25".
The linkstate is one of the following:
SNA CONNECT PENDING = The
virtual circuit to the remote system has been established and an SNA
connection (which must use the virtual circuit) is in the process
of being established.
SNA CONNECTED = The SNA and X.25
connections to the remote system have been established.
SNA DISCONNECT PENDING
= The SNA connection is in the process of terminating. However, the
X.25 connection still exists.
SNA ERROR RECOVERY = The X.25
link has received invalid frames from the remote system and is in
the process of recovery. Note that the SNA connection, the X.25 connection,
and the SNA node are all still active.
VC CONNECT PENDING = A request
for a virtual circuit from the X.25 network has been made, but the
virtual circuit has not been obtained. Note that this state is
valid for a switched virtual circuit (SVC) only.
VC CONNECTED = The virtual circuit
to the remote system has been established; however, no SNA connection
has been made. Note that this state is valid for a switched virtual
circuit (SVC) only.
Tracing is "ON" if link-level tracing is on, or "OFF" if the tracing is off.
The tracefile is the name of the link trace file.
The NI name is the NS network interface that the link is using.
The inactivity timeout is the number of minutes the Qualified Logical Link Control (QLLC) module will wait between incoming packets. If the value is "0", the timer is disabled.
The VC type is "PVC" for an X.25 permanent virtual circuit, or "SVC" for an X.25 switched virtual circuit.
The PVC number is the number that identifies the permanent virtual circuit for the X.25 link. Note that this information is displayed for a PVC only.
The remote address is the X.25 network address of the remote system. Note that this information is displayed for an SVC only.
The call direction is "IN" if the remote system initiated the call, or "OUT" if the HP 3000 initiated the call. Note that this information is displayed for an SVC only.
Max call retries is the maximum number of times the Qualified Logical Link Control (QLLC) module will try to connect to the remote system without success. Note that this information is displayed for an outgoing SVC only.
The call retry delay is the number of seconds the QLLC module will wait between attempts to connect to the remote system. Note that this information is displayed for an outgoing SVC only.
The call retry count is the number of times call retries have been attempted. Note that this information is displayed for an outgoing SVC only.
Total bytes is the total number of bytes sent from and received by the link.
Data bytes is the total number of bytes of data sent from and received by the link.
Control bytes is the total number of bytes of control information sent from and received by the link.
Total packets is the total number of packets sent from and received by the link.
Data packets is the total number of packets of data sent from and received by the link.
Control packets is the total number of packets of control information sent from and received by the link.
Token Ring Link-Level Status Information |
|
An example of a Token Ring link-level status display is given below, and the terminology used is described after the example. Note that when link-level status information is displayed, the corresponding session-level status information is also displayed. (Since the session-level status terminology is described later under "Session-Level Status Information," it is not described here.)
Example
If a Token Ring link is being used, typing
SNACONTROL STATUS;NODE=IBMNODE;LINK=ALL
where IBMNODE is already active could generate this display:
Linkname: IBMNODE Linktype: IEEE8025 Linkstate:
CONNECTED
Physical Path: 48 Data Rate: 16 Mbps
Current Station Address: 10-00-90-00-00-07
Default Station Address: 10-00-90-90-C8-46
Functional Address Mask: 00-00-00-00
Transmits no error: 6614976 Receives no error: 6620830
Transmit byte count: 2368752825 Receives byte count: 2367702513
Transmit errors: 0 Receive errors: 0
NAME TYPE NAU STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
XPORTPU PU_SSCP 0 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 1 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 2 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 3 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 4 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 5 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 6 RESET MANAGER.SYS OFF
PFA2 DEP_LU 2 PEND_ACT_R PITEST.PUT21R40 NMTC0090.PUB.SYS
PFA3 DEP_LU 3 ACTIVE PITEST.PU2140 OFF
PFA4 DEP_LU 4 PEND_RST_R PITEST.PU2140 OFF
PFA5 DEP_LU 5 PEND_SON PITEST.PU2140 OFF
PFACLASS DEP_LU 1 RESET PITEST.PU2140 OFF
NAME TYPE LFSID STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
INDLU1 IND_LU 1,0200 PEND_ACT_L PITEST.PUT21R40 OFF
INDLU2 IND_LU 1,0201 PEND_RST_L PITEST.PUT21R40 OFF
INDLU3 IND_LU 1,0202 PEND_RST_N PITEST.PUT21R40 OFF
INDLU4 IND_LU ------ RESET PITEST.PUT21R40 OFF
|
Terminology
The linkname is the same as the node name.
The linktype is "IEEE8025".
The linkstate is one of the following:
NOT CONNECTED = The Token Ring
device adapter has not been inserted into the network.
CONNECTED = The Token Ring device adapter
has been inserted into the network.
RETRY = The Token Ring device adapter is retrying
to insert into the network.
The physical path is the address of the token ring adapter card.
The data rate is the speed of the token ring (in megabits per second).
The current station address is the currently-active station address.
The default station address is the factory-configured default station address.
The function address mask is the address mask as described in the IBM Token-Ring Network Architecture Reference.
Transmits no error is the number of frames transmitted without errors.
Receives no error is the number of frames received without errors.
Transmit byte count is the number of bytes transmitted without errors.
Receive byte count is the number of bytes received without errors.
Transmit errors is the number of frames not successfully transmitted because of errors.
Receive errors is the number of frames received with errors.
Session-Level Status Information |
|
Regardless of the type of link being used, the same session-level status information is displayed. An example of a session-level status display is given below, and the terminology used is described after the example.
Example
If either an SDLC, X.25, or token ring link is being used, typing
SNACONTROL STATUS;NODE=IBMNODE
where IBMNODE is already active could generate this display:
SESSION STATE STATUS FOR NODE : IBMNODE
NAME TYPE NAU STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
XPORTPU PU_SSCP 0 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 1 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 2 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 3 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 4 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 5 ACTIVE MANAGER.SYS OFF
XPORTLU LU_SSCP 6 RESET MANAGER.SYS OFF
PFA2 DEP_LU 2 PEND_ACT_R PITEST.PUT21R40 NMTC0090.PUB.SYS
PFA3 DEP_LU 3 ACTIVE PITEST.PU2140 OFF
PFA4 DEP_LU 4 PEND_RST_R PITEST.PU2140 OFF
PFA5 DEP_LU 5 PEND_SON PITEST.PU2140 OFF
PFACLASS DEP_LU 1 RESET PITEST.PU2140 OFF
NAME TYPE LFSID STATE USER TRACE FILE
======== ======= ====== ========== =============== ==========================
INDLU1 IND_LU 1,0200 PEND_ACT_L PITEST.PUT21R40 OFF
INDLU2 IND_LU 1,0201 PEND_RST_L PITEST.PUT21R40 OFF
INDLU3 IND_LU 1,0202 PEND_RST_N PITEST.PUT21R40 OFF
INDLU4 IND_LU ------ RESET PITEST.PUT21R40 OFF
|
Terminology
The name is the PU or LU name. Note that XPORTPU and XPORTLU are the internal names that are used by SNA Transport. XPORTPU is a PU name used for maintaining the PU-SSCP session. XPORTLU is the LU name used for maintaining the LU-SSCP sessions (for dependent LUs).
The type is the type of the session. This is either PU-SSCP for PU-SSCP sessions, LU-SSCP for LU-SSCP sessions, DEP_LU for dependent LU-LU sessions, or IND_LU for independent LU-LU sessions.
The NAU is the session's Network Addressable Unit number in decimal. All PU-SSCP, LU-SSCP, and dependent LU-LU sessions have a NAU.
The LFSID is the session's Local-form session identifier. It consists of the OAF-DAF assignor indicator (ODAI) followed by the session identifier (SID) in hexadecimal. Only independent LU-LU sessions have an LFSID. If an independent LU-LU session is in RESET state, it will not have an LFSID.
The session state is one of the following:
ACTIVE = The session with the remote system
has been established. Note that the SNA services are connected to
the remote system in this state only.
PEND_ACT_L = Pending activation local. An
activation request has been sent by the HP 3000. However, a response
to the activation request has not yet been received.
PEND_ACT_R = Pending activation remote. An
activation request has been received by the HP 3000. However, a
response to the activation request has not yet been sent.
PEND_RST_B = Pending reset both. Both
the HP 3000 and the remote system have sent UNBIND requests. The
HP 3000 received the remote system's UNBIND request before receiving
the response to the UNBIND the HP 3000 sent.
PEND_RST_L =Pending reset local. An
UNBIND has been sent to the remote system, but no response has been
received.
PEND_RST_N = Pending reset negative
response. A BIND has been sent to the remote LU session, a negative
response (-RSP) has been received from an intermediate routing node,
and the SNA service must generate an UNBIND to send to the remote
LU session.
PEND_RST_R = Pending reset remote. A
deactivation request has been received from the remote system, but
no response has been sent.
PEND_SON = Pending session outage notification. A
Session Outage Notification (SON) deactivation request has been generated
internally or received on the link. However, no response has been
sent.
RESET = The initial state. No sessions
exist.
The user is the name of the user or program that owns the session.
The trace file is the name of the trace file, if tracing has been turned on. If tracing is off, OFF is displayed.
