 |
» |
|
|
|
This section describes how to create your Customized System
Load Tape (CSLT) from CD-ROM source media using the CD-ROM tool,
hpinstal. To create the CSLT using hpinstal Start HPINSTAL. :RUN HPINSTAL.INSTALL.SYS
|
Select the appropriate option. If you select a subsys
option, your system software must be on the same release level as
the subsys product. Please enter the number corresponding to the software you want to install. 1Update this system 2 Update this system and install patches from a PowerPatch tape 3 Create a CSLT for another system 4 Create a CSLT with PowerPatch patches for another system 5 Complete the update of this system using a CSLT created on another system 6 Add SUBSYS products to this system 7 Add SUBSYS products and install patches from a Powerpatch tape 8 Exit ? Help on the above actions Enter your choice >>_
|
Reply to the prompt for the LDEV number. Press [Return]
to use the default of device class TAPE, or enter the LDEV number
of the device where you want the CSLT to be created. The device
you specify applies to all tape requests. The file equation for the output device (where the CSLT is created) defaults to DEV=TAPE. If you prefer to designate a specific tape device, please enter its LDEV number now (RETURN for default) >>
|
If you are creating a CSLT on a local system to
apply to a Remote system, proceed to Step 5. If you are performing an Add-on or Update task for a local
system only, proceed to Step 6.
Remote TasksRespond
to the prompt to specify a Base Group.
If you have
not added customized files or a different configuration
to your CSLT, press [Return]. This is the typical
condition. If you have added customized
files or a different configuration to your CSLT through the use
of a Base Group, specify that Base Group name now. (Refer to Appendix E “CD-ROM Resources” for directions
on creating a Base Group.) When ready to create the CSLT, HPINSTAL will copy your current configuration group to HPCONFIG.SYS and use that as the base group. If you have customized a configuration group that you would like HPINSTAL to use as the base group while creating the CSLT, please provide it now. Base group (RETURN for default) >>
|
Proceed to Step 6.
If needed, edit or create a PRODLIST.PUB.SYS
file. A master product list was included with the CD-ROM. This list
shows all products available to be installed, and needs to be checked
against your keyword certificate now. Respond YES to
accept the master list of products at the prompt. Begin validation of the master product list... Reading PRODLIST.PUB.SYS... DONE Your master list contains the following n subsystems: [The subsystems included in the PRODLIST file are listed here.] Is the master list of products correct (Y/N)?>
|
Type or verify the master product keyword at the
prompt. Your keyword validates the master product list. The keyword is included on the keyword certificate that comes
with the CD-ROM disks. The keyword is not
case sensitive. But you must enter it exactly as it appears including
the alphanumerics, slash (/), and hyphen (-). If you have a keyfile.pub.sys
file, hpinstal automatically reads
the keyword for your products from the keyfile.pub.sys
file. (Refer to Appendix E “CD-ROM Resources”
for directions on creating and using the keyfile.pub.sys
file.) Please enter your keyword. The keyword accompanies the CD-ROM. It is made up of fourteen (14) characters including alphanumerics, the slash(/) and the hyphen (-). You must enter your keyword EXACTLY AS IT APPEARS: Your keyword >>  |  |  |  |  | NOTE: Add-on product keyword can only be entered interactively. |  |  |  |  |
Select to install all or a portion of the listed
products: Enter Y to select all products
on the list. Enter N to select a subset
of the products, proceed to Step 10. Do you want to install all of the above products? (YES/NO)>> If you accidentally type N,
are viewing the list of products, and you do not wish to make any
changes to the list: Type two
slashes (//) or [Return]. Confirm the products as you did in Step 7.
Optionally, create a subset list of products from
the full list of products. This is typically done to create a CSLT for use on a remote
system, but can be done for your local system as well. To create a subset list of products: Enter N
to the prompt in Step 9. The N option puts HPINSTAL
into customization mode. HPINSTALL
displays the list of products in the current PRODLIST.install.sys
file. Review this list and make changes as needed. Edit the file to create the list of products that will be
installed using the CSLT. Use the CSLT created in this section to
modify your remote system.
If you are performing a PowerPatch task, proceed
to Step 12. If you are performing an Add-on or Update task without a PowerPatch,
proceed to Step13.
PowerPatch TasksRestore
patch information, qualify patches, and restore the patch files. Mount the
PowerPatch tape, as prompted. Reply to the tape request. Respond Y to accept
the list of qualified patches, as prompted: Do you want to incorporate these patches (Y/N)? Remount the PowerPatch tape, as prompted; Please remount the PowerPatch tape and put it on line so that HPINSTAL can retrieve the patch files selected. Reply to the tape request. Proceed to Step 13.
Create the CSLT. Mount a write-enabled tape on the appropriate tape drive and
reply to the tape request, as prompted. This can take up to two
and a half hours. hpinstal
determines the files that belong to your selected list of products. Resolving product-level dependencies ... DONE Determining the subsystem files to be installed ... DONE hpinstal stages
system libraries and creates the CSLT. This can take from one up
to two and a half hours. Making a temporary copy of the SL ... DONE Making a temporary copy of the XL ... DONE Making a temporary copy of the NL ... DONE The installer will next update staged copies of the System SL, XL, and NL HPINSTAL updates
the temporary copies of the system libraries and displays status
messages: Installing the SUBSYS and patch code, if any . . . Modifying SL.INSTALL.SYS ... done Translating SL.INSTALL.SYS ... done Modifying XL.INSTALL.SYS ... done Modifying NL.INSTALL.SYS ... done Modifying System Intrinsics ... done Creating a new START PME ... done Creating the CSLT ...
|
Insert the second CD-ROM disk if prompted, then press [Return]. The installer is done with the CD-ROM currently mounted. Please remove the CD-ROM and insert the second CD-ROM, marked MPE_v.uu.ff_2. When the second CD-ROM volume is mounted, press RETURN to continue >> Thank You Verifying the second CD-ROM . . . Done. The second CD-ROM volume has been mounted. Continuing with installing from the CD-ROM volume MPE_v.uu.ff_2.
|
After the CSLT is created, dismount the tape, label
it CSLT v.uu.ff,
and set it to read only. The final response messages vary depending upon the CSLT option
you selected. Basically, the response is: Phase I of HPINSTAL is now complete: A warning message displays, if applicable. WARNING -- This program cannot install the products listed below. (INSTWARN #1) Record on your checklist any products HPINSTAL
cannot completely install. HPINSTAL will automatically
cleanup files, exit, and return you to the MPE/iX prompt. Purging temporary files and cleaning up ... If you are creating a CSLT on a local system to
apply to a Remote system, proceed to Step 17. If you are performing an Add-on or Update task for a local
system only, omit Step 17, and go to the next section on your checklist.
Remote TasksRefer to
Appendix E “CD-ROM Resources” for directions
on creating multiple copies of the CSLT with the SLTCOPY
command for use at remote systems. If you are creating additional modified CSLTs for use on remote
systems, reinvoke HPINSTAL and
select option 3, "Create a CSLT for another system,"
for each CSLT you need. If each remote system is unique, you will
need to modify the PRODLIST file
for each system. Refer to Appendix E “CD-ROM Resources” for directions on creating additional
PRODLIST files. Creating the CSLT using
HPINSTAL completed. Go to the next section on your checklist.
|