 |
» |
|
|
|
This section lists procedures for preparing to use the CD-ROM
update and add-on tool, HPINSTAL.
Refer to Appendix E “CD-ROM Resources” for
additional CD-ROM set up information. To prepare your local system to create a CSLT using HPINSTAL: Log on. :HELLO MANAGER.SYS,INSTALL;HIPRI |
If you are not working at the console, allow yourself the
VSCLOSE and VSOPEN
commands. :ALLOW MANAGER.SYS;COMMANDS=VSCLOSE,VSOPEN |
Start the LP and
streams_device. :SPOOLER LP;START
:STREAMS streams_device |
An LP device must be configured in SYSGEN.
A common streams_device
value is 10. Already spooled and streamed messages might display. Load the CD-ROM disk labelled MPE_v.uu.ff_1 into the CD-ROM disk drive. v.uu.ff
is the version.update.fix
level of the software. Write the v.uu.ff
level on the checklist. HPINSTAL prompts for the
second disk when required. If you have SCSI CD-ROM drives, manually mount the
disk. where ldev#
is the logical device number of the SCSI CD-ROM disk drive. When the CD-ROM disk is loaded, AVRSCSI
returns the message: Successfully mounted LDEV n |
Verify that the CD-ROM drive status indicates MASTER-RO. This is a sample DSTAT response: LDEV-TYPE STATUS VOLUME (VOLUME SET - GEN)
11-CD-ROM MASTER-RO HPINSTAL (MPE_C.55.00_1-0)
12-CD-ROM MASTER-RO HPINSTAL (MPE_C.55.00_2-0) |
If the DSTAT status
shows LONER, put the CD-ROM disks
on-line. :VSOPEN MPE_v.uu.ff_1
:VSOPEN MPE_v.uu.ff_2 |
If you have only one CD-ROM drive, put only the first CD-ROM
disk on-line now. Run the DSTAT command again to verify the
drives have a status of MASTER-RO. Create directory entries to enable access to group
INSTUTIL on volume set MPE_v.uu.ff_1. If the INSTUTIL
group is non-existent, create the INSTUTIL
group and set home volume set. :NEWGROUP INSTUTIL;HOMEVS=MPE_v.uu.ff_1 |
If the home volume set field displays a different
v.uu.ff
than the new version: :ALTGROUP INSTUTIL.SYS;HOMEVS=MPE_v.uu.ff_1 |
If you are performing an Update task, proceed to
Step 11. If you are performing an Add-On task, proceed to Step 12.
Update TasksThis step
is optional. Create files for product and keyword references.
If you have
an old PRODLIST.PUB.SYS file, purge
it or verify all products. Create PRODLIST.PUB.SYS
file. This file lists all the products that are on your support
contract. The list should match the list on your keyword certificate.
Refer to "Creating a Product List" in Appendix E “CD-ROM Resources” for directions
on creating a PRODLIST file. HPINSTAL references this
file to determine automatically which products will be applied to
your system. Create KEYFILE.PUB.SYS
file. this file contains the keyword necessary to unlock the products
in PRODLIST.PUB.SYS on the CD-ROM.
Refer to Appendix E “CD-ROM Resources” for
directions on creating a keyfile
file. If you are adding-on new products, the new product
numbers and keyword will only be requested interactively as part
of the HPINSTAL process. Proceed to Step 13.
If you are creating a CSLT for applying to a Remote
system, proceed to Step 13. If you are performing a Add-on or Update task for the local
system only, proceed to Step 14.
Remote TasksThis step
is optional. If you are creating a CSLT on the local system, for
applying to a remote system, and you have additional files you want
to include on the STORE portion
of the CSLT: Create a
file, addfile,
that lists any files you want to include on the CSLT, such as third-party
or in-house product files. Set up a file equation to equate addfile
to indirlst. hpinstal
checks the indirlst file for additional
files and adds them to the CSLT. :FILE INDIRLST=addfile.group.account |
Proceed to Step 14.
Set up the HPINSTAL
environment by invoking the SETUP
script. Execute SETINIT command to cleanup any
previous HPINSTAL accounting structure,
if prompted. A series of messages display. The process takes about five
minutes. The final message is: If you are performing a PowerPatch task, proceed
to Step 16. If you are performing an Add-on or Update task without a PowerPatch,
proceed to the next section on your checklist.
PowerPatch TasksMount the
PowerPatch tape and restore the latest version of the HPINSTAL
tool. :FILE TAPE;DEV=TAPE
:RESTORE *TAPE;H@.INSTALL;SHOW;DEV=1 |
Two files, HPINSTAL and HICAT000,
are added to the INSTALL.SYS group.
Preparing to Run HPINSTAL
completed. Proceed to the next section on your checklist.
|
