 |
» |
|
|
|
Throughout the activities described in Chapter 5 “Modifying Your System” several types
of messages may display. Below is a description of some of the more
common error and warning messages and a general description of the
appropriate response to those messages. Disk Space Messages |  |
At different stages, AUTOINST
searches for required amounts of non-contiguous and contiguous disk
space. In the section "3.6 Estimating Disk Space"
in Chapter 3 “Planning for Your Task” you verified
if you had sufficient disk space. If however, AUTOINST
cannot find sufficient non-contiguous disk space, it displays an
error message and terminates. If AUTOINST cannot
find sufficient contiguous disk space, it will display an error
message and prompt you whether to continue. You can continue while
you are creating the CSLT, but you must find the required contiguous
disk space prior to applying the CSLT. Refer to Appendix C “Managing Disk Space” for additional
information on clearing disk space.
AUTOINST Disk Space MessagesThe following messages are generated by AUTOINST.
While the operating system is running, AUTOINST
attempted to put files into a holding area in the install
group prior to calling SYSGEN to
create a SLT. Warning -- The Installer cannot find enough contiguous disk space on LDEV #1 for UPDATE to update with the CSLT created by the Installer. (INSTWARN #5) You must create 60000 sectors of contiguous disk space on LDEV #1 BEFORE updating with the CSLT created by the Installer. If you wish to continue with this installation and create the disk space after the Installer is done (but before updating with the CSLT) respond with ``YES'' to the following prompt. If you wish to stop the Installer now to create the disk space, respond with a ``NO'' Continue with the installation now and create disk space later >> Y/N Warning -- The Installer cannot find enough contiguous disk space on LDEV #1 for UPDATE to update with the CSLT created by the Installer. (INSTWARN #5) You must create 60000 sectors of contiguous disk space on LDEV #1 BEFORE updating with the CSLT created by the Installer.
|
To recover from the above two messages, ensure that you have
sufficient disk space before proceeding with your modification task. UPDATE Disk Space MessageThe following message is generated by the UPDATE
utility. UPDATE was not able to
put all the files on disk. UPDATE
skips non-critical files and exists. WARNING: UPDATE tried to find 60,000 sectors of contiguous disk space on LDEV1 for its work, but it could only find nnnnnnn sectors. Before continuing, refer to the Installation Manual for instructions on collecting enough contiguous space on LDEV1 for the update. If you still have questions after attempting the procedures outlined in the manual, call your HP support representative for help. You may override this warning and continue with the update, but HEWLETT-PACKARD STRONGLY DISCOURAGES THIS COURSE OF ACTION. DO NOT override this warning unless you have a full backup available and the time to REINSTALL your system. If UPDATE runs out of space on LDEV1, you risk having to REINSTALL. Override this warning message [OVERRIDE/NO; default=NO]?
|
At the end of UPDATE, where the system normally boots, the
system will stop. The operator must boot the machine manually. Messages
will stay on the console. The console will have the following message
on it. ERROR. This UPDATE did not restore all files from the tape.(UPDERR 1001) There were # files not restored because of out of disk space. (1) There were # files not restored for other than disk space reasons. (2) There is more information about the error conditions in previous messages. START the system, create more free disk space and run this UPDATE again. (1) Correct the problems and run this UPDATE again. (2) Correct the problems, START the system, create more free disk space and run this UPDATE again. (3) END of LOAD (update).
|
INSTALL Group Capabilities |  |
The INSTALL group is created
with certain capabilities which AUTOINST
needs to run. If these capabilities are not present, the following
message is displayed: Program requires more capabilities than group is allowed. (LDRERR505) Native mode loader message 505 UNABLE TO LOAD PROGRAM TO BE RUN. (CIERR 625)
|
If this message appears on the console where AUTOINST
is invoked, use CHGROUP to change
to the PUB.SYS group, use ALTGROUP
to add the BA, IA, PM, MR, DS,
and PH capabilities to the INSTALL
group. Use CHGGROUP to return to
your original group. Zero Installation Files |  |
When installation files are streamed, progress messages display.
The message may indicate zero installation files. This only means
that the products you are installing do not require an installation
file. AUTOINST continues with the product installation. Qualified Patch List |  |
When the patch evaluation is complete, each patch is listed
with the result of its qualification process. Some patches are followed
by one or more additional patches listed as dependencies. For a
patch to qualify, all of its patch dependencies must also qualify. The absence of a product, or the presence of a product that
has been patched with a site-specific patch can cause a patch to
not qualify. Decide whether you want to install the patches that qualified
for your system. For additional information on available patches,
refer to READ BEFORE INSTALLING for PowerPatch
Releases or Communicator 3000 for Express
Releases. Manually Installed Products Warning |  |
Manually installed products, have installation files that
cannot be streamed automatically and require special attention.
If there are products like this on your SUBSYS tape, a warning message
is displayed with the product name(s). These products must be installed after updating with the CSLT.
Refer to Appendix A “Manually Installed Products” for
installation instructions.
|