HP 3000 Manuals HP 3000 Manuals
900 Series HP 3000 Computer Systems AutoRestart/iX User's Guide HP Part No. 36375-90001 Printed in U.S.A. Edition Third Edition E1092
________________________________________________________________________ |The information contained in this document is subject to change | |without notice. | | | |Hewlett-Packard makes no warranty of any kind with regard to this | |material, including, but not limited to, the implied warranties of | |merchantability or fitness for a particular purpose. Hewlett-Packard | |shall not be liable for errors contained herein or for direct, | |indirect, special, incidental, or consequential damages in connection | |with the furnishing or use of this material. | | | |Hewlett-Packard assumes no responsibility for the use or reliability | |of its software on equipment that is not furnished by Hewlett-Packard.| | | |This document contains proprietary information that is protected by | |copyright. All rights are reserved. Reproduction, adaptation, or | |translation without prior written permission is prohibited, except as | |allowed under the copyright laws. | ________________________________________________________________________ Copyright (c) 1992 by Hewlett-Packard Company ________________________________________________________________________ |Use, duplication, or disclosure by the U.S. Government is subject to | |restrictions as set forth in subparagraph (c) (1) (ii) of the Rights | |in Technical Data and Computer Software clause at DFARS 252.227-7013. | |Rights for non-DoD U.S. Government Departments and agencies are set | |forth in FAR 52.227-19 (c) (1,2). | | | |Hewlett-Packard Company | |3000 Hanover Street | |Palo Alto, CA 94304 U.S.A. | ________________________________________________________________________ Restricted Rights Legend Printed 1992 Printing History The following table lists the printings of this document, together with the respective release dates for each edition. The software version indicates the version of the software product at the time that this document was issued. Many product releases do not require changes to the document; therefore, do not expect a one-to-one correspondence between product releases and document editions. Edition Date Software Version --------------------------------------------------------------------------------------- First Edition April 1990 A.40.00 Second Edition June 1992 B.40.00 Third Edition October 1992 C.45.00 Preface The AutoRestart/iX User's Guide (36375-90001) provides the information necessary to configure and manage AutoRestart/iX, a product that enables a 900 Series HP 3000 to automatically reset itself in the event of a system abort, to save dump failure state information to disk, and to restart itself, all without the need for operator intervention. This user's guide is written for the system administrator who has completed Hewlett-Packard system administrator training courses. This manual is divided into five chapters: Chapter 1 Introduction provides an introduction to AutoRestart/iX functionality, as well as hardware and software requirements for the product. Chapter 2 Preparing Your System describes the steps necessary to prepare the hardware and software required by AutoRestart/iX. Chapter 3 Configuring and Managing the Dump-to-Disk and Mini-Dump Features describes the steps necessary to configure the dump-to-disk and mini-dump functionality provided by AutoRestart/iX. In addition, dump-to-disk and mini-dump management tasks are described in detail. Chapter 4 Configuring and Managing the Autoboot Feature describes the steps necessary to configure and manage the restart and autoboot functionality provided by AutoRestart/iX. In addition, autoboot management tasks are described in detail. Chapter 5 Managing Your AutoRestart/iX System describes tasks related to managing an AutoRestart/iX system after initial configuration. Conventions UPPERCASE In a syntax statement, commands and keywords are shown in uppercase characters. The characters must be entered in the order shown; however, you can enter the characters in either uppercase or lowercase. For example: COMMAND can be entered as any of the following: command Command COMMAND It cannot, however, be entered as: comm com_mand comamnd italics In a syntax statement or an example, a word in italics represents a parameter or argument that you must replace with the actual value. In the following example, you must replace filename with the name of the file: COMMAND filename bold italics In a syntax statement, a word in bold italics represents a parameter that you must replace with the actual value. In the following example, you must replace filename with the name of the file: COMMAND(filename) punctuation In a syntax statement, punctuation characters (other than brackets, braces, vertical bars, and ellipses) must be entered exactly as shown. In the following example, the parentheses and colon must be entered: (filename):(filename) underlining Within an example that contains interactive dialog, user input and user responses to prompts are indicated by underlining. In the following example, yes is the user's response to the prompt: Do you want to continue? >> yes { } In a syntax statement, braces enclose required elements. When several elements are stacked within braces, you must select one. In the following example, you must select either ON or OFF: COMMAND { ON } { OFF} [ ] In a syntax statement, brackets enclose optional elements. In the following example, OPTION can be omitted: COMMAND filename [OPTION] When several elements are stacked within brackets, you can select one or none of the elements. In the following example, you can select OPTION or parameter or neither. The elements cannot be repeated. COMMAND filename [ OPTION ] [ parameter] Conventions (Continued) [...] In a syntax statement, horizontal ellipses enclosed in brackets indicate that you can repeatedly select the element(s) that appear within the immediately preceding pair of brackets or braces. In the example below, you can select parameter zero or more times. Each instance of parameter must be preceded by a comma: [,parameter][...] In the example below, you use the comma only as a delimiter if parameter is repeated; no comma is used before the first occurrence of parameter: [parameter][,...] |...| In a syntax statement, horizontal ellipses enclosed in vertical bars indicate that you can select more than one element within the immediately preceding pair of brackets or braces; however, each particular element can be selected only once. In the following example, you must select A, AB, BA, or B. The elements cannot be repeated. { A} |...| { B} ... In an example, horizontal or vertical ellipses indicate where portions of an example have been omitted. In a syntax statement, the space symbol shows a required blank. In the following example, parameter and parameter must be separated with a blank: (parameter) (parameter) The symbol indicates a key on the keyboard. For example, RETURN represents the carriage return key or Shift represents the shift key. CTRLcharacterCTRLcharacter indicates a control character. For example, CTRLY means that you press the control key and the Y key simultaneously.