HP 3000 Manuals HP 3000 Manuals
Creating the HP36375 and DISKDUMP groups
AutoRestart/iX requires two groups, HP36375 and DISKDUMP, located in the
TELESUP account. Two NEWGROUP commands are required (if you are creating
a nonsystem volume set) to configure each of the new groups in both the
system volume set and the nonsystem volume set.
The following enables you to create both groups on your system:
1. Log on as MANAGER.SYS. At the system prompt, enter:
:HELLO MANAGER[/userpass].SYS[/acctpass]
2. Ensure that the TELESUP account exists on your system. At the
system prompt, enter:
:LISTACCT TELESUP
If TELESUP exists, proceed to step 3. If TELESUP does not exist,
you must create the account before proceeding. To create the
TELESUP account, enter:
:NEWACCT TELESUP,MGR;CAP=SM,AM,AL,GL,&
DI,OP,UV,LG,CS,ND,SF,BA,IA,PM,MR,DS,PH,CV
3. The ONVS option of the NEWACCT command allows the TELESUP account
groups to exist on any nonsystem volume set (for example, a
nonsystem volume set called DISKDUMP_VOLUME_SET).
To copy the TELESUP account structure to a nonsystem volume set,
enter:
:NEWACCT TELESUP,MGR;ONVS=DISKDUMP_VOLUME_SET
4. Ensure that the group HP36375.TELESUP resides on your system. At
the system prompt, enter:
:LISTGROUP HP36375.TELESUP
If HP36375.TELESUP does not reside on your system, go to step 5.
If HP36375.TELESUP resides on your system, it was created on your
system master volume set (MPE XL_SYSTEM_VOLUME_SET) when you
installed AutoRestart/iX, during an update or an installation. To
move HP36375.TELESUP to the nonsystem volume set (for example,
DISKDUMP_VOLUME_SET), perform the following steps:
a. Mount a write-enabled tape on the tape drive. Put the tape
drive online.
b. Store all files located in HP36375.TELESUP to tape. At the
system prompt, enter:
:FILE T;DEV=TAPE
:STORE @.HP36375.TELESUP;*T;SHOW
c. Reply to the tape request.
__________________________________________________________
NOTE Remove the write ring and keep the tape containing
the files stored from HP36375.TELESUP. You will
restore these files in step 8, after you create
HP36375.TELESUP on the nonsystem volume set.
__________________________________________________________
d. Use the PURGEGROUP command to purge HP36375.TELESUP. At the
system prompt, enter:
:PURGEGROUP HP36375.TELESUP
5. Use the HOMEVS option of the NEWGROUP command to create accounting
information for the group HP36375.TELESUP on the system volume
set. At the system prompt, enter:
:NEWGROUP HP36375.TELESUP;CAP=IA,&
BA,PM,MR,DS,PH;HOMEVS=DISKDUMP_VOLUME_SET
6. Use the ONVS option of the NEWGROUP command to create
HP36375.TELESUP on the nonsystem volume set (for example,
DISKDUMP_VOLUME_SET). At the system prompt, enter:
:NEWGROUP HP36375.TELESUP;ONVS=DISKDUMP_VOLUME_SET
7. Ensure that HP36375.TELESUP has been successfully installed on the
nonsystem volume set. At the system prompt, enter:
:LISTGROUP HP36375.TELESUP
The LISTGROUP command displays the home volume set where
HP36375.TELESUP currently exists.
8. If you had to purge HP36375.TELESUP prior to recreating it on the
nonsystem volume set, you must restore the AutoRestart/iX files to
HP36375.TELESUP, now located on the nonsystem volume set.
a. Mount a write-enabled tape on the tape drive. Put the tape
drive online.
b. Restore AutoRestart/iX files to HP36375.TELESUP. At the
system prompt, enter:
:FILE T;DEV=TAPE
:RESTORE *T;@.@.@;SHOW
c. Reply to the tape request.
9. Use the HOMEVS option of the NEWGROUP command to create accounting
information for the group DISKDUMP.TELESUP on the system volume
set. At the system prompt, enter:
:NEWGROUP DISKDUMP.TELESUP;CAP=IA,&
BA,PM,MR,DS,PH;HOMEVS=DISKDUMP_VOLUME_SET
10. Use the ONVS option of the NEWGROUP command to create
DISKDUMP.TELESUP on the nonsystem volume set (for example,
DISKDUMP_VOLUME_SET). At the system prompt, enter:
:NEWGROUP DISKDUMP.TELESUP;ONVS=DISKDUMP_VOLUME_SET
11. Confirm that DISKDUMP.TELESUP has been successfully installed on
the nonsystem volume set. At the system prompt, enter:
:LISTGROUP DISKDUMP.TELESUP