HP 3000 Manuals HP 3000 Manuals
Class Errors (Cont'd.)
Class Error 9: Console Path Test
Class Error 9
Console path related errors and/or channel I/O errors take the following
multiplexed code form:
01wx
9yzz
where:
w = CIO slot number (<> C)
x = Device address (always 0 for the console)
y = CIO mid-bus slot number
zz = IODC driver error code 00 - 7F.
-------------------------------------------------------------
0100 MESSAGE None.(I)
9y80
CAUSE I/O dependent code (IODC) from channel I/O bus
(CIO) in console path fails.
ACTION None. If problem recurs or is suspected cause of a
future system problem or failure, contact your
Hewlett Packard Support Representative.
-------------------------------------------------------------
0100 MESSAGE No message. System halts. (E)
9y88
CAUSE No working console is found. Autoboot disabled.
ACTION Connect console or replace existing console.
Reboot system.
-------------------------------------------------------------
01C0 MESSAGE No message. Self-test continues. (W)
9yzz
CAUSE Access port self-test fails. "zz" = AP self-test
code (00-7F).
ACTION If AP not functional, reset the system from the
front panel. If a soft reset/transfer of control
is needed, set switch 3 on the system monitor card
to the open position and reset the system from the
front panel. If AP is functional and can reset the
system, note the error as a possible console path
or CIO bus problem should a future problem or
system failure occur.
-------------------------------------------------------------
01C0 MESSAGE No message. Self-test continues. (W)
9yF0
CAUSE Access port read of the hexadecimal display fails.
ACTION None. Note error should a future system problem
occur.
-------------------------------------------------------------
01C0 MESSAGE No message. Self-test continues. (W)
9yFF
CAUSE No access port is found.
ACTION If an access port exists and remains functional,
note error should the problem cause a future
problem or system failure. If AP is disabled or
not functioning and you have reset the system from
the front panel, ignore warning message.
-------------------------------------------------------------
Class Error A: Boot Path Test
Boot device related errors and/or channel I/O errors take the following
multiplexed code form:
01wx
Ayzz
where:
w = CIO slot number (<> C)
x = Device address (always 0 for the console)
y = CIO mid-bus slot number
zz = IODC driver error code 00 - 7F.
-------------------------------------------------------------
0100 MESSAGE Boot Error: First display. Boot Error: Second
Ay80 display. Boot from Primary Path (Y or N)?>
CAUSE IODC load from the CIO channel in console path
fails.
ACTION Check that the tape drive is functional. (Check
switch setting if switch selector is used.)
Recable new drive. If measures fail, contact your
Hewlett-Packard Support Representative and boot
from primary path if possible.
-------------------------------------------------------------
0100 MESSAGE Boot Error: First display. Boot Error: Second
AyF0 display. Boot from Primary Path (Y or N)?>
CAUSE LIF volume label error occurs. The media may have
been improperly initialized.
ACTION Check that the tape drive is functional. (check
switch setting, if switch selector is used.) check
that the mounted tape is a boot tape. Recable new
drive or replace suspect tape. If measures fail,
contact your Hewlett-Packard Support Representative
and boot from primary path if possible.
-------------------------------------------------------------
01wx MESSAGE Boot Error: First display. Boot Error: Second
AyF8 display. Boot from Primary Path (Y or N)?>
CAUSE IPL checksum fails. The utility (or ISL) being
read from tape is possibly corrupted.
ACTION Try using the utility from another tape, such as
from the master backup. If problem persists,
contact your Hewlett-Packard Support Representative
and boot from the system disk.
-------------------------------------------------------------
Class Error B: Initialization Messages
When the system halts, the reason for the halt can be seen on the SPU
control panel status display (hex display). The first number is the
source of the halt call, and following it are numbers of the form 0nxx
where n is a number that starts at 1 and increments. The reason can be
interpreted by stringing the xx values together to form a number.
When the monitor is the source of the halt, the first number is B000.
System abort uses B007. The following codes relate the cause of the
error.
-------------------------------------------------------------
0001 MESSAGE No message. System halts. (E)
thru
0019
CAUSE The break handler (to RDB) was reentered.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0020 MESSAGE No message. System halts. (E)
CAUSE A break zero (0) instruction is encountered without
RDB.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0021 MESSAGE No message. System halts. (E)
CAUSE An unknown high priority machine check occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0022 MESSAGE No message. System halts. (E)
CAUSE A nonrecoverable low priority machine check occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0028 MESSAGE No message. System halts. (E)
CAUSE Reinit_iodc fails to read entry_init.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
0029 MESSAGE No message. System halts. (E)
CAUSE Reinit_iodc fails to read entry_io.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0030 MESSAGE No message. System halts. (E)
CAUSE Image does not fit the first memory controller.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
003E MESSAGE No message. System halts. (E)
CAUSE A nonrecoverable taken branch or break trap occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
003F MESSAGE No message. System halts. (E)
CAUSE A bad instruction is received from RDB.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
0040 MESSAGE No message. System halts. (E)
CAUSE A configured module is lost on powerfail.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0041 MESSAGE No message. System halts. (E)
CAUSE A bus converter is lost on powerfail.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0042 MESSAGE No message. System halts. (E)
CAUSE A bus converter was added on powerfail.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
0043 MESSAGE No message. System halts. (E)
CAUSE memory was added on powerfail.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0044 MESSAGE No message. System halts. (E)
CAUSE A module was added on powerfail and it generated an
address conflict.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0045 MESSAGE No message. System halts. (E)
CAUSE Memory self-test fails in map_system_state.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0046 MESSAGE No message. System halts. (E)
thru
004E
CAUSE Error occurs on call to entry_init in reinit_iodc.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
005B MESSAGE No message. System halts. (E)
thru
005F
CAUSE The parallel card driver (RDB communications)
encounters an error.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0066 MESSAGE No message. System halts. (E)
thru
006E
CAUSE Error occurs on call to entry_io in CONSOLE_READ or
CONSOLE_WRITE.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0080 MESSAGE No message. System halts. (E)
thru
0099
CAUSE A trap which neither RDB nor the operating system
is prepared for occurs.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
00F1 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable instruction TLB error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F2 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable data TLB error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F3 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable bus address error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F4 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable bus error on I/O space occurs.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
00F5 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable bus error on memory read or write
occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F6 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable bus error I/O space write occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F7 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable bus error with slave processor
occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00F8 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable cache tag error occurs.
ACTION Contact your Hewlett-Packard Support
Representative.
-------------------------------------------------------------
00F9 MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable data cache error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00FA MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable assist (coprocessor) error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
00FB MESSAGE No message. System halts. (E)
CAUSE Nonrecoverable instruction cache error occurs.
ACTION Try rebooting the system. If error recurs, contact
your Hewlett-Packard Support Representative.
-------------------------------------------------------------
0131 MESSAGE Illegal configuration.
CAUSE You may have an illegal configuration, such as
trying to run MPE/iX on an 800-series CPU.
ACTION CAll your HP service representative. Do not try to
INSTALL or UPDATE or the system will halt with a
message, B0000 DEAD 0131.
-------------------------------------------------------------