HP 3000 Manuals HP 3000 Manuals
Displaying Current File Information
The SHOW command (abbreviated SH) displays the file information currently
set through SYSFILE. SHOW has the following parameters:
SHOW (SH) [FILE = AUTO ]
[ BOOT ]
[ CATALOG ]
[ CMSL ]
[ DCC ]
[ IPL ]
[ NMLIB ]
[ SPROG ]
[ ALL ]
[DEST = OFFLINE ]
AUTO shows all the autoboot images.
BOOT shows all the boot images currently configured.
CATALOG shows the system catalog in use.
CMSL shows the CMSL (compatibility mode segmented library) in use.
DCC shows which file will be used for network configuration.
IPL shows the IPL images in use.
NMLIB shows the NM library names.
SPROG shows the specified system program names.
ALL shows all of the above information.
OFFLINE redirects the output of the SHOW command to SYSGEN's listing
file, SYSGLIST. Using OFFLINE does not immediately generate a printout.
The information is sent to SYSGLIST until you either enter the OCLOSE
command or exit SYSGEN. Exiting SYSGEN or using OCLOSE closes SYSGLIST
and prints the file.
To see current file information, enter the SHOW command and at least one
parameter:
sysfile>SH NMLIB
NM LIB = NL.PUB.SYS
To show all the current system file information for system libraries,
programs and the message catalog, enter SHOW ALL or SHOW:
______________________________________________________________________________________
| |
| |
| sysfile>SHOW ALL |
| DISC AUTOBOOT = NONE |
| TAPE AUTOBOOT = NONE |
| SYSTEM CATALOG = CATALOG.PUB.SYS |
| CM SL = SL.PUB.SYS |
| NMCONFIG FILE = NONE |
| NM LIB = NL.PUB.SYS |
| |
| BOOT FILE FILENAME TYPE |
| --------- -------- ---- |
| ISL.MPEXL.SYS ISL.MPEXL.SYS disc boot |
| DUMP.MPEXL.SYS DUMP.MPEXL.SYS disc boot |
| START.MPEXL.SYS START.MPEXL.SYS disc boot |
| INSTALL.MPEXL.SYS INSTALL.MPEXL.SYS tape boot |
| UPDATE.MPEXL.SYS UPDATE.MPEXL.SYS tape boot |
| A1002AI.MPEXL.SYS A1002AI.MPEXL.SYS both boot |
| A1002AM.MPEXL.SYS A1002AM.MPEXL.SYS both boot |
| A1002AP.MPEXL.SYS A1002AP.MPEXL.SYS both boot |
| A1100AI.MPEXL.SYS A1100AI.MPEXL.SYS both boot |
| A1100AM.MPEXL.SYS A1100AM.MPEXL.SYS both boot |
| A1100AP.MPEXL.SYS A1100AP.MPEXL.SYS both boot |
| CAEXR.MPEXL.SYS CAEXR.MPEXL.SYS both boot |
| IOMAP.MPEXL.SYS IOMAP.MPEXL.SYS both boot |
| CLKUTIL.MPEXL.SYS CLKUTIL.MPEXL.SYS both boot |
| DISCUTIL.MPEXL.SYS DISCUTIL.MPEXL.SYS both boot |
| SADPATCH.MPEXL.SYS SADPATCH.MPEXL.SYS both boot |
| SAT.MPEXL.SYS SAT.MPEXL.SYS both boot |
| MPROC.MPEXL.SYS MPROC.MPEXL.SYS both boot |
| UNIPROC.MPEXL.SYS UNIPROC.MPEXL.SYS both boot |
| MDIAG.MPEXL.SYS MDIAG.MPEXL.SYS both boot |
| TDIAG.MPEXL.SYS TDIAG.MPEXL.SYS both boot |
| EDBC.MPEXL.SYS EDBC.MPEXL.SYS both boot |
| EDPROC.MPEXL.SYS EDPROC.MPEXL.SYS both boot |
| |
| IPL FILE FILENAME TYPE |
| --------- -------- ---- |
| ISL2.MPEXL.SYS ISL2.MPEXL.SYS tape ipl |
| MMSAVE.MPEXL.SYS MMSAVE.MPEXL.SYS disc ipl |
| |
______________________________________________________________________________________
Example 8-5. SYSFILE Configurator SHOW ALL Output
________________________________________________________________________________________
| |
| |
| SYSTEM PROGRAM FILENAME TYPE |
| -------------- -------- ---- |
| IFHPIBFS.PUB.SYS IFHPIBFS.PUB.SYS system prog |
| XL.PUB.SYS XL.PUB.SYS system prog |
| PSIMDBDL.DIAG.SYS PSIMDBDL.DIAG.SYS system prog |
| PSINIODL.DIAG.SYS PSINIODL.DIAG.SYS system prog |
| SYSDIAG.PUB.SYS SYSDIAG.PUB.SYS system prog |
| . . . |
| . . . |
| DTCSWI04.PUB.SYS DTCSWI04.PUB.SYS system prog |
| DTCSWJ04.PUB.SYS DTCSWJ04.PUB.SYS system prog |
| DTCSWK04.PUB.SYS DTCSWK04.PUB.SYS system prog |
| DTCSWL04.PUB.SYS DTCSWL04.PUB.SYS system prog |
| DTCSWM04.PUB.SYS DTCSWM04.PUB.SYS system prog |
| |
________________________________________________________________________________________
Example 8-5. SYSFILE Configurator SHOW ALL Output (continued)
The add commands (AAUTO, ABOOT, ACMSL, and ASPROG) add objects to the
list of files dumped onto SYSGEN's tape:
AAUTO adds an autoboot file to the list of files.
ABOOT adds a boot image to the list of files.
ACMSL adds a segment to a temporary copy of the CMSL, which SYSGEN
automatically manages.
ASPROG adds a system program or other file to the list of files.
Adding autoboot files
The AAUTO command (abbreviated AA) adds an autoboot file to the list of
files dumped onto SYSGEN's tape. The command has the following
parameters:
AAUTO (AA) [FILE =] autobootfilename
[TYPE = DISC ]
[ TAPE ]
[ BOTH ]
FILE specifies the file name that contains autoboot commands. If it is
not fully qualified with group and account name, it defaults to the
current group and account. If the specified file does not exist, an
error occurs, and the system issues a message.
NOTE Always use fully qualified file names.
TYPE specifies the type of autoboot files to add. TYPE allows the
following types:
DISC Specifies that the file is applicable to a disk
boot only.
TAPE Specifies that the file is applicable to a tape
boot only.
BOTH Specifies that the file is applicable to both
disk boot and tape boot.
There can be only one disk and one tape autoboot file, although neither
is required. The tape and disk autoboot files become TAPEAUTO.MPEXL.SYS
and AUTOBOOT.MPEXL.SYS, respectively.
Adding boot files
The ABOOT command (abbreviated AB) adds a boot image to the system file
configuration. The command has the following parameters:
ABOOT (AB) [IMAGE =] bootimagename
[FILE =] filename
[TYPE = DISC ]
[ TAPE ]
[ BOTH ]
IMAGE specifies the name of a boot image. If the specified boot image
already exists, an error occurs.
FILE adds the file name of the boot image. If the file name is not fully
qualified, it defaults to the current group and account. If SYSGEN is
run from a different group and account when the tape is made, unexpected
results occur (for example, cannot find the specified files). If the
file to be added does not exist, an error occurs.
TYPE specifies the type of boot images to add. TYPE allows the following
types:
DISC Specifies that the file is applicable to a disk
boot only.
TAPE Specifies that the file is applicable to a tape
boot only.
BOTH Specifies that the file is applicable to both
disk boot and tape boot.
To add file information for the boot image, enter the ABOOT command, file
name, and at least one parameter:
sysfile>ABOOT START2.UTIL.SYS START2.UTIL.SYS TYPE=DISC
Adding a segment to the compatibility mode segmented library (CMSL)
The ACMSL command (abbreviated AC) adds a segment to the CMSL. The
command has the following parameters:
ACMSL (AC) [SEG =] segmentname
[FILE =] filename
[MODE = S ]
[ C ]
[ P ]
[ U ]
SEG specifies a new segment name with a maximum of eight characters. If
an existing segmentname is specified, an error occurs.
FILE specifies a file name to be added to the CMSL. The filename
parameter can be fully qualified with group and account. If not, it
defaults to the current group and account. If filename cannot be found,
an error occurs.
MODE indicates where the added SL segment is to reside. It expects one
of the four options listed below. Other entries cause errors.
P Declares a segment to be a permanently allocated
user segment. This parameter performs the same
function as the ALLOCATE command.
S Declares a segment to be a permanently allocated
system intrinsic segment (in virtual memory).
C Declares a segment to be a core-resident system
intrinsic segment.
U Declares a segment to be a temporarily allocated
user segment.
Adding file names to dump to tape
The ASPROG command (abbreviated AS) adds a system program or other file
to the list of files to be saved on tape. The command has the following
parameters:
ASPROG (AS) [PROG =] program-name
[FILE =] filename
PROG expects a system program name. If the specified program-name
already exists in the system program list, an error occurs.
FILE expects a file name to be used as the system program. If it is not
fully qualified with group and account name, it defaults to the current
group and account. If the specified filename does not exist, an error
occurs.
To add a program to tape, enter the program and file name:
sysfile>ASPROG FCOPY.PUB.SYS FCOPY.PUB.SYS