HP 3000 Manuals HP 3000 Manuals
(Subsystem 236) (contd.)
5288 MESSAGE Could not create output spoolfile directory
symbol table.
---------------------------------------------------------------
5289 MESSAGE Could not create a virtual object to hold output
spoolfile queue entries.
---------------------------------------------------------------
5290 MESSAGE Could not create output spoolfile queue head
symbol table.
---------------------------------------------------------------
5291 MESSAGE Could not re-open a spoolfile already opened by
the current process.
---------------------------------------------------------------
5292 MESSAGE Could not gain access to the label of a file
already opened by the current process.
---------------------------------------------------------------
5293 MESSAGE FCLOSE of a spoolfile failed.
---------------------------------------------------------------
5294 MESSAGE Read or write of a spoolfile's label extension
failed.
---------------------------------------------------------------
5295 MESSAGE Spoolfile does not exist on any of the volumes
currently mounted.
---------------------------------------------------------------
5296 MESSAGE Low-level open of spoolfile failed due to file
descriptor allocation limitations.
---------------------------------------------------------------
5297 MESSAGE System error performing low-level open of
spoolfile.
---------------------------------------------------------------
5298 MESSAGE The spoolfile was still in the CREATE state when
the system was interrupted. It could not be
recovered, and has been deleted.
---------------------------------------------------------------
5299 MESSAGE Infinite loop corruption detected in output
spoolfile directory. Reboot your system to rebuild
the directory. If the problem recurs, CONTACT YOUR
SE.
---------------------------------------------------------------
5300 MESSAGE Unknown error performing low-level open of
spoolfile.
---------------------------------------------------------------
5302 MESSAGE Output spoolfile has invalid state.
---------------------------------------------------------------
5303 MESSAGE Attempt to add a new output spoolfile queue head
entry failed due to existence of a queue head for
the same output device or class.
---------------------------------------------------------------
5304 MESSAGE Output spoolfile queue head table overflow.
CONTACT YOUR SE.
---------------------------------------------------------------
5305 MESSAGE Output spoolfile queue corruption detected.
Invalid link to a queue's first entry. CONTACT
YOUR SE.
---------------------------------------------------------------
5306 MESSAGE Output spoolfile queue corruption detected.
Invalid forward link. CONTACT YOUR SE.
---------------------------------------------------------------
5307 MESSAGE Output spoolfile queue corruption detected.
Invalid backward link. CONTACT YOUR SE.
---------------------------------------------------------------
5309 MESSAGE Unexpected escape encountered inserting an output
spoolfile into a spoolfile queue.
---------------------------------------------------------------
5310 MESSAGE Could not find the device or class queue head
entry matching the target device or class of an
output spoolfile.
---------------------------------------------------------------
5312 MESSAGE Could not remove a spoolfile from the spooling
queues.
---------------------------------------------------------------
5313 MESSAGE Could not retrieve the address of a workarea
created for spooling subsystem command execution.
---------------------------------------------------------------
5315 MESSAGE Could not create a spooling command/AIF work
area.
---------------------------------------------------------------
5316 MESSAGE Could not expand a spooling command/AIF work
area.
---------------------------------------------------------------
5317 MESSAGE Could not deallocate a spooling command/AIF work
area.
---------------------------------------------------------------
5318 MESSAGE Directory error while preparing to retrieve file
system directory information for a set of
spoolfiles.
---------------------------------------------------------------
5319 MESSAGE Directory error while retrieving file system
directory information for a set of spoolfiles.
---------------------------------------------------------------
5320 MESSAGE Unknown/invalid spooler process type.
---------------------------------------------------------------
5321 MESSAGE Encountered transaction management error while
updating creator of an output spoolfile in its
label and label extension.
---------------------------------------------------------------
5322 MESSAGE Encountered error writing changes to an output
spoolfile's file label extension when changing its
creator.
---------------------------------------------------------------
5323 MESSAGE When changing creator of an output spoolfile in
its label and label extension, the changes to these
structures were aborted because a user transaction
under which these system transactions occurred was
aborted.
---------------------------------------------------------------
5340 MESSAGE SPOOLF ;PRINT encountered an error reading source
file.
---------------------------------------------------------------
5341 MESSAGE SPOOLF ;PRINT encountered an error writing to
target file.
---------------------------------------------------------------
5342 MESSAGE You cannot SPOOLF ;PRINT a Private output
spoolfile.
---------------------------------------------------------------
5343 MESSAGE You cannot SPOOLF ;SPSAVE a Private output
spoolfile.
---------------------------------------------------------------
5344 MESSAGE You cannot SPOOLF ;DEFER a spoolfile in the
PROBLEM state unless you also ALTER it to a valid
target device/class.
---------------------------------------------------------------
5345 MESSAGE You cannot SPOOLF ;DEFER an output spoolfile
which has already been printed and has moved to the
'SPSAVE' state.
---------------------------------------------------------------
5346 MESSAGE You cannot alter the output priority of a
spoolfile in the SPSAVE state.
---------------------------------------------------------------
5347 MESSAGE You cannot alter the number of copies of a
spoolfile which is either Private or in the SPSAVE
state.
---------------------------------------------------------------
5348 MESSAGE You cannot alter the target device/class of a
spoolfile in the SPSAVE state.
---------------------------------------------------------------
5349 MESSAGE SPOOLF ;ALTER or SPOOLF ;DELETE of more than one
spoolfile is disabled until the output spoolfile
directory has been rebuilt following a system
startup.
CAUSE You entered SPOOLF [O]@; ALTER or DELETE while the
output spoolfile directory was still being rebuilt.
This is not allowed because the command could miss
some files which had not yet been inserted into the
directory.
ACTION This situation only occurs for a few minutes
following system startups. Try your command again
a few minutes later.
---------------------------------------------------------------
5350 MESSAGE The specified or defaulted target device/class
does not exist, is not output spoolable, or does
not have its spooling queues open.
---------------------------------------------------------------
5351 MESSAGE Unable to obtain file information, the FFILEINFO
intrinsic failed.
---------------------------------------------------------------
5352 MESSAGE The specified file is not a spoolfile.
---------------------------------------------------------------
5353 MESSAGE You tried to SPOOLF ;PRINT an empty file.
---------------------------------------------------------------
5354 MESSAGE SPOOLF ;PRINT aborted by BREAK.
---------------------------------------------------------------
5355 MESSAGE Could not change the STDLIST device in
JOB/SESSION tables.
---------------------------------------------------------------
5356 MESSAGE File does not exist or could not be created.
---------------------------------------------------------------
5357 MESSAGE SPOOLF ;PRINT -- valid range of copies is 1 to
65535.
---------------------------------------------------------------
5358 MESSAGE SPOOLF ;PRINT -- valid range of priorities is 0
to 14.
---------------------------------------------------------------
5359 MESSAGE Cannot open the file for exclusive access because
it is already open.
---------------------------------------------------------------
5360 MESSAGE The specified lockword does not match the
lockword on the file.
---------------------------------------------------------------
5361 MESSAGE You cannot UNDEFER a spoolfile in the PROBLM
state.
---------------------------------------------------------------
5362 MESSAGE You cannot UNDEFER a spoolfile in the SPSAVE
state.
---------------------------------------------------------------
5367 MESSAGE You cannot alter the attributes of an input
spoolfile.
---------------------------------------------------------------
5368 MESSAGE You cannot delete an ACTIVE ":DATA" input
spoolfile, that is, one currently being submitted
via the STREAM command.
---------------------------------------------------------------
5369 MESSAGE You cannot delete an output spoolfile which is in
the CREATE state.
---------------------------------------------------------------