HP 3000 Manuals HP 3000 Manuals
ERROR MESSAGES (continued)
Validation Errors
Error Message Cause/Action
201 Field ! not found in Input field in OUTPUT RECORD
form !. menu not found in specified form.
202 Field ! not found in any Input field in OUTPUT RECORD
form in input forms menu not found in any form in the
sequence. corresponding INPUT FORMS menu.
203 Reformat identifier ! is First form specified on INPUT
not a unique reformat FORMS menu is not unique to the
identifier. reformat file. Use a form name
that has not been specified as a
reformat identifier on another
menu.
204 Internal error: Data type See error 206.
is bad.
205 Output record length is Change either the total output
greater than globally record length on the OUTPUT RECORD
defined record length. menu, or the record length on the
GLOBALS menu, or start a new record
using the start record marker.
206 Internal error: Bad entry Internal descriptions of fields
in field table. Illegal are bad. Press ENTER again. If
field type. that fails, delete and recreate
the offending format.
207 Error opening reformat Refer to the file system error
file. (FSERR !!!!) for the cause of the open failure.
208 A unique reformat See error 203.
identifier is required.
210 Internal error: OFST table See error 206. OFST is Old Field
is bad. Symbol Table.
211 Internal error: Field table See error 206.
is bad. Set'next failed.
212 Form name must begin with Form name cannot start with a
an alphabetic character. special character or a digit.
213 Form name cannot have The only non-alphanumeric
embedded " "'s or "."'s. character allowed in a form name
is the underline "_".
214 Form name may contain only Use the correct naming conventions:
alphas, digits and "_"'s. A name may contain letters, digits,
or the underline, must start with
a letter, and have no more than
15 characters.
215 Internal error in Internal error in recording the
ADJUST'ALL'START'COL. change in the default starting
position of each field, a change
resulting from altering the field
or record separators in the
globals menu.
216 Internal error reading Error reading an internally
reformat intermediate used record from the reformat file.
record for !.
217 WARNING: Start column Starting column for output record
goes beyond global output specified on OUTPUT RECORD menu is
record length. greater than the record length on
the GLOBALS menu. To avoid
truncation, change one of the two
specifications.
218 Embedded blank form names A form name consisting of a blank
not allowed in a sequence. found in the INPUT FORMS menu.
Remove the blank line from the
sequence.
219 Internal error: Data type See error 204.
is bad.
220 WARNING: This field A field specified on the OUTPUT
causes output record size RECORD menu is beyond the record
to be too big. size set on the GLOBALS menu.
Change the GLOBALS specification
or delete the field.
Field Table Errors
Error Message Cause/Action
301 Internal error: OFST Space allocated for dynamic array
ALLOCATE failed. is insufficient.
302 Internal error: OFST Attempt to read internal record
record missing. Write failed because the record did not
failed previously. exist.
303 Internal error: OFST Attempt to write an internal
write failed. record failed.
(FSERR !!!!)
304 Internal error: OFST
does not have any more
room.
305 Output field name ! not Output field name on OUTPUT RECORD
unique. menu must be unique for the record.
Use output field name to provide
unique name.
306 Internal error: OFST See error 301.
search range error.
307 Internal error reading OFST Failure to read an intermediate
record. (FSERR !!!!) (internal) record.
308 Internal error: OFST start See error 301.
order.
309 Internal error: OFST end See error 301.
order.
313 Internal error: OFST See error 301.
unreferenced error.
316 Internal error: OFST See error 301.
update screen order error.
320 Internal error: OFST wrap See error 301.
loop error.
400 Internal error: Field table See error 301.
allocation failed.
401 Internal error: Field table See error 302.
record missing. Prev
write failed.
402 Internal error reading Field names in output record
FST from forms file. menu cannot be checked against
(FSERR !!!!) the forms file because of
internal inability to read
information from forms file.
403 Internal error writing See error 303.
FST to reformat file.
(FSERR !!!!)
404 Internal error: Field See error 301.
table has no more room.
405 Internal error reading See error 402.
input seq from reformat
file. (FSERR !!!!)
406 Internal error: Input See error 302.
seq table record missing.
Prev write failed.
407 Internal error writing seq
table to refmt file.
(FSERR !!!!)
450 Form ! does not exist Form name specified on INPUT
in the forms file. FORMS menu is not in forms
file. Check name and correct it.
451 Internal error reading Failure to read list of forms
glob forms buf from form in the forms file.
file. (FSERR !!!!)
452 Internal error: Global
forms file rec missing.
Prev write failed.
453 Internal error reading Failure to read list of all
field name table for fields for a particular form
form !. (FSERR !!!) in the forms file.
460 Internal error in reading
globals from forms file.
(FSERR !!!!)
461 Internal error: Allocation
of form'glob'buf failed.
462 Internal error: Allocation
of form'flds'buf failed.
463 Internal error: Allocation
of literal table failed.
464 Internal error: Literal
table record missing.
Prev write failed.
465 Internal error: Error
reading literal table
record. (FSERR !!!!)
466 Internal error writing
literal table record.
(FSERR !!!!)
468 Internal error: Allocation
of global buffer failed.
469 Form ! does not exist in
this forms file.
Menu Processing Errors
Error Message Cause/Action
501 Selection field cannot Enter one of the following codes
be blank. in the MAIN menu selection box:
A, X, G, F, L, or D.
502 Reformat identifier ! not A reformat id entered on the
found. MAIN menu is not in the reformat
file. Check the INPUT FORMS
menu or correct the identifier.
503 Output field name ! not An output field name entered
found. on the MAIN menu is not in the
reformat file. Check the
OUTPUT RECORD menus or correct
the field name.
504 No reformat identifier A selection on the MAIN menu
was specified. requires a reformat identifier.
Enter the identifier or change
the selection.
505 There are no input A reformat identifier was
form sequences in the specified, but no INPUT FORMS
reformat file. menu has been entered.
506 No reformat to be "D" was entered in MAIN menu
deleted was specified. selection box; specify the
reformat identifier to be
deleted.
507 No such reformat A reformat identifier on the
identifier exists. MAIN menu is not on any INPUT
FORMS menu.
508 Main selection field Enter one of the listed codes.
must be "A!, "X", "G",
"F", "L" or "D".
509 This field must be The reformat id for deletion
blank when deleting. should be in the righthand box;
clear in the lefthand box.
510 Listing is not done Enter "L" to list, and a
on a field level. reformat identifier in the
lefthand box; you cannot list
a single field.
511 Form name must be When you enter "X" to compile
blank for compile. the reformat file, you cannot
enter a reformat identifier.
512 Field name must be When you enter "X" to compile
blank for compile option. the reformat file, you cannot
enter an output field name.
513 Form name is not When you enter "A" to add a
specified when adding reformat, do not specify the
a form. reformat id; reformat id's are
entered on the INPUT FORMS menu.
514 Fields are not added Output fields are added on the
from the MAIN menu. OUTPUT RECORD menu, not using
the "A" option of the MAIN menu.
515 Form name must be blank A selection was made on the
for this option. MAIN menu that cannot use a
reformat id. Clear the
reformat id box.
516 Field name must be blank A selection was made on the
for this option. MAIN menu that cannot use an
output field name. Clear the
output field box.
Menu Processing Utility Errors
Error Message Cause/Action
600 NUMn can have digits only A value other than a digit was
from "O" to "9". entered for a NUMn type field;
change the data type or the
selection.
606 Must be NUMn, DIG, IMPn, Enter one of the listed codes as
MDY, DMY, YMD, or CHAR. the data type of this field; n
can be a digit 0-9 for NUM, 1-9
for IMP.
608 Justify field must be Enter one of the codes to justify
"L", "R", "C", or " ". field Left, Right, or Center;
default is Right justify for
numbers or dates, no
justification for characters.
609 Checkdigit must be If you want to insert a check
either "10" or "11". digit, specify 10 for modulus 10,
11 for modulus 11.
610 Checkdigit can only be If you want to add a checkdigit,
added to fields of type change the data type on the
DIGIT or CHAR. OUTPUT FIELD menu.
611 Internal error: Substring Intrinsic ASCII failed.
start column value could
not be displayed.
612 Numeric fields cannot be When the input field is a number,
converted to fields of you cannot specify a data type
date type. of MDY, DMY, or YMD on the
OUTPUT FIELD menu. Change the
data type.
613 Date fields cannot be When the input field is a date,
converted to fields you cannot specify DIG, IMPn, or
of numeric type. NUMn as the data type on an
OUTPUT FIELD menu. Change the
data type to a date or CHAR.
614 Fields of type CHAR When the input field is type CHAR,
cannot be converted to you cannot change the data type
other data types. on an OUTPUT FIELD menu. Leave
the type as CHAR.
615 Internal error: Input Intrinsic ASCII failed.
length value could not
be displayed.
617 Only fields of type NUM, If the input field is not one
NUMn and IMP can be signed. of the listed types, you cannot
specify a sign on the OUTPUT FIELD
menu.
618 Sign must be "L", "R", Only the listed codes or a space
"F", "Z", "N" or " ". can be entered on the SIGN box
of the OUTPUT FIELD menu. Correct
your entry.
620 Plus field must be "Y" If you want the plus sign
or"N". retained in the field, enter Y in
the PLUS SIGN? box; if N or blank,
only minus signs are inserted.
621 Expected "F", "V", or Enter one of the listed codes in
"U" in record format field. the Output Record Format box of the
GLOBALS menu; default is F (fixed
length).
622 Recordsize must be a Enter a positive integer less
numeric value less than than 32767 in the Record Length
32767. box of the GLOBALS menu, or leave
the default length of 80
characters.
624 Expected literal, system Record terminator or field
constant or ASCII separator string can only be a
equivalent in string. quoted string, the numeric
equivalent of an ASCII c.haracter
preceded by $, or a system
constant: $LF, $CR, $GS, $US, or
$RS.
625 Output field must be If you enter 10 or 11 in the
expanded to allow for CDIGIT box of the OUTPUT FIELD
checkdigit. menu, be sure to increase the
size of the output field on the
OUTPUT RECORD menu.
626 Internal error: Checkdigit See error 610
option not valid for data
type.
627 Strip fields must start Enclose any characters in a STRIP
and end with a quote. box of the OUTPUT FIELD menu
between quotes.
628 Use "" or " to indicate Use double quotes for any
" or ' inside a literal. quotation marks within a literal
(literal is entered in the
GLOBALS menu.)
629 Plus option cannot be If you want a plus sign, you
"Y" if sign option is "N". must also specify where you
want any sign in the SIGN box
of the OUTPUT FIELD menu.
630 Fill all has already Enter a character in Fill ALL
filled leading blanks. OR Fill Leading, not both.
631 Fill all has already Enter a character in Fill ALL
filled trailing blanks. OR Fill Trailing, not both.
632 IMPn can have digits Number of implied decimal
only from "0" to "9". places must be a digit.
Menu Init and Processing Errors
Error Message Cause/Action
702 Internal error. Intrinsic
ASCII failed.
703 Largest legal integer Error in Record Length field of
value is 32767. GLOBALS menu.
704 Length of field cannot Negative value specified as
be negative. field length on OUTPUT RECORD
menu.
705 Internal error Internal error in writing the
initializing OUTPUT header part of the output record
RECORD menu. menu.
(COMSTATUS !!!!)
706 Internal err writing Internal error in writing
old output recdef to user's specifications--part of
to screen (COMSTATUS !!!!) output menu.
707 Internal error reading Attempt to read the output
output recdef from screen. record menu failed.
(COMSTATUS !!!!)
708 Internal error in writing
output recdef to refmt file.
(FSERR !!!!)
709 Internal error reading
source rec from reformat
file. (FSERR !!!!)
710 Internal error in writing If trying to change the forms
source rec to reformat file name in REFSPEC make sure
file. (FSERR !!!!) that the original forms file does
not exist by temporarily renaming
it.
714 Internal error writing the
window. (COM'STATUS !!!!)
716 Internal error writing the
error cursor pos'n.
(COM'STATUS !!!!)
742 Internal error: Start Intrinsic ASCII failed.
column could not be
displayed.
743 Internal error: Length Intrinsic ASCII failed.
could not be displayed.
744 Forms file is not a The forms file specified on the
valid forms file or forms FORMS FILE menu is not valid.
file is not compiled. Correct the name or go back to
FORMSPEC and compile the
forms file.
745 Internal error in
T'READ'NO'HOME. Bad key
read. (COMSTATUS !!!!)
746 Internal error in cursor
positioning before read.
747 Internal error writing the
current reformat rec
for !. (FSERR !!!)
748 Internal error
initializing Input Form
Menu for reformat id !.
749 Internal error reading
MAIN MENU form.
(COMSTATUS !!!!)
750 Internal error showing
MAIN MENU form.
(COMSTATUS !!!!)
751 Internal error getting
MAIN MENU form.
(COMSTATUS !!!!)
752 Internal error in
initializing output
record menu.
(COMSTATUS !!!!)
753 Internal error: VSETERROR
failed. (COMSTATUS !!!!)
754 Internal error: FGETINFO
failed.
755 File is not a forms file. File name specified on the FORMS
FILE menu does not name an
existing forms file. Correct
the name.
756 File is not a reformat The file name specified on the
file. REFORMAT file menu does not
identify an existing reformat
file.
757 Internal error: Could not Intrinsic FGETINFO failed.
get information from
reformat file.
758 Internal error: Could not Intrinsic FGETINFO failed.
get information from
forms file.
Menu Controller Errors
Error Message Cause/Action
802 The PREV key is not There is no previous menu.
allowed here.
803 The function key just This key has not meaning on the
hit is not defined for current menu.
this mode.
805 Error getting next form !.
(COM'STATUS !!!)
806 Internal error in
VSHOWFORM. (COM'STATUS !!!!)
807 Internal error in
VREADFIELDS.
(COM'STATUS !!!!)
808 Internal error in VGETBUF.
(COM'STATUS !!!!)
810 Internal error in writing
reformat rec for reformat !.
(FSERR !!!)
811 Internal error in reading
reformat rec for reformat !.
(FSERR !!!)
812 Internal error in reading
globals record.
(FSERR !!!!)
815 NEXT is not meaningful Enter a forms file name on the
until a forms file name FORMS FILE menu before using
is specified. the NEXT key.
816 NEXT is not appropriate. Use the MAIN menu to go to
There are no more reformats. a particular reformat, or use
PREV REFORMAT key to go to a
prior reformat.
817 NEXT is not meaningful Enter a reformat file name
until a reformat file name on the REFORMAT FILE menu
is specified. before using the NEXT key.
818 You cannot specify more You have already entered 255
than 255 reformats. INPUT FORMS menus; try to use
fewer.
819 The NEXT REFORMAT key is There are no more INPUT FORMS
inappropriate. There are menus in the file.
no more reformats.
820 There are no previous The current reformat is the first
reformats. one. Use the main menu to go
to a particular reformat or use
the NEXT REFORMAT key to go to
the next input forms sequence.
821 Internal error in writing
globals table record.
(FSERR !!!!)
822 WARNING: Changes in The OUTPUT FIELD menu may be
input forms menu may have affected by changes to the
invalidated this menu INPUT FORMS menu.
823 WARNING: Changes in input The OUTPUT RECORD menu may
forms menu may have be affected by changes to the
invalidated this menu INPUT FORMS menu.
824 Internal error: Missing
record for reformat !.
Prev write failed.
825 NEXT'REFORMAT is not
meaningful until forms
file name is specified.
826 NEXT'REFORMAT not
meaningful until reformat
file name is specified.
827 Cannot go to MAIN MENU
until reformat file name
has been specified.
828 Cannot go to MAIN MENU until Do not press MAIN key until you
forms file name has been have entered forms file name
specified. on FORMS FILE menu.
829 Reformat file was modified You pressed EXIT before
since last compile. Press compiling the reformat file;
EXIT to exit. press MAIN to go to MAIN menu
to compile, or press EXIT to
exit without compiling.
Init and Compile Errors
Error Message Cause/Action
906 Error writing reformat !.
(FSERR !!!)
913 Internal error closing
your forms file.
(FSERR !!!!)
914 Internal error in storing
the field symbol table.
(FSERR !!!! )
917 Internal error in storing
OFST. (FSERR !!!!)
918 Error closing reformat
file. (FSERR !!!!)
919 Internal error in
closing REFSPEC forms file.
(FSERR !!!!)
920 Internal error in closing
terminal file. (FSERR !!!!)
921 Internal error in writing
globals record on exit.
(FSERR !!!!)
922 Internal error in storing
literal table. (FSERR !!!!)
923 Error in opening user's Refer to the file system error
forms file. (FSERR !!!!) to determine the cause of the
open failure.
Compile Error
Error Message Cause/Action
1000 Internal error on compile.
Bad field type.
1001 Internal error writing
field intermediate code
rec. (FSERR !!!!)
1002 Internal error writing
reformat code record.
(FSERR !!!!)
1003 Internal error: Allocation
of compile buffer failed.
1004 Internal error writing
globals code record.
(FSERR !!!!)
1005 Internal error reading
field intermediate code
rec. (FSERR !!!!)
1006 REFSPEC version has The specified reformat file
been changed. Reformat was produced on an earlier
file invalid. version of REFSPEC.
1007 Reformat file is empty. Enter A to add a reformat
There is nothing to before entering X to compile.
compile.
1008 Error in output record Go to the OUTPUT RECORD menu
menu in reformat !. for the specified reformat,
and make correction.
1009 Error in input forms Go to the specified reformat
menu in reformat !. (INPUT FORMS menu) and make
correction.
1010 Output field ! of Go to the specified OUTPUT
reformat ! is in error. FIELD menu and make correction.
1011 Internal error writing
code rec for input forms
seq. (FSERR !!!!)
VPLUS INTRINSIC MESSAGES
VOPENTERM and VCLOSETERM Messages
Error Message Cause/Action
001 Internal error: Terminal FCONTROL or FSETMODE intrinsic
file initialization failed.
failed.
002 Your terminal is not VPLUS works on the
supported by VPLUS. HP terminals listed in
Appendix G.
003 VPLUS does not VPLUS does not run on an
run on a series I. HP Series I computer system.
004 The terminal status VOPENTERM's request for terminal
request failed. status failed. Check that
strapping is correct. May also
be data comm problem.
005 The terminal allocation Message used only with the
failed. 2640A terminal, which is not
supported by VPLUS.
Reserved words in the COMAREA
are not initialized to zeros.
006 The terminal needs the Refer to Appendix G for
H strap in (closed). instructions on how to strap your
terminal for VPLUS.
007 Internal error: HP2640 Possible block mode or data
mode could not be comm problem.
correctly set.
008 Internal error: HP2645 See error 007.
mode could not be
correctly set.
009 The terminal open FOPEN intrinsic failed.
failed. (FSERR !)
010 The terminal close failed. FCLOSE intrinsic failed.
(FSERR !)
011 Sorry, this device is not Refer to Appendix G for a list of
supported by VPLUS. supported terminals.
012 The HP2640B needs straps You must strap this terminal
A, C, H in (closed); (and the 2644A) yourself; other
D, F, G out. terminals are strapped
automatically. (Refer to
Appendix G.)
013 The HP2644A needs straps You must strap this terminal
A, C, H in (closed); (and the 2640B) yourself;
D, G out. other terminals are strapped
automatically. (Refer to
Appendix G.)
014 The HP2645A/41A/48A Note that these terminals
needs straps A, C, H, J should be configured
in (closed); D, G out. automatically by VPLUS.
015 Terminal type incorrectly Possible block mode or data
determined. comm problem. Check straps.
Note: 2645 multipoint straps
should never be touched!
016 Internal error HP2645A See error 015.
multipoint terminal mode
not correctly set.
017 Comarea too short for The Comarea must be 85 words
run-time HP3075/6 for HP 3075/6 terminals. Set
terminals. Comarealen to 85.
018 Non-page/block mode Redefine terminal type.
terminal types not (Note: VPLUS requires a terminal
supported. which supports page/block mode.)
019 Internal error: See System Manager.
FDEVICECONTROL should not
return ccg.
021 Invalid terminal type. TERMTYPE used is a printer
terminal type.
General Intrinsic Error Messages
Error Message Cause/Action
020 Error detected by host Check the Comarea item
language. FILERRNUM for the host language
error number.
021 Invalid terminal type. See 021 above.
023 Environment control file
access failed.
VOPENFORMF and VCLOSEFORMF Messages
Error Message Cause/Action
040 Internal error: DLSIZE Stack size or MAXDATA too small.
failed; there is not Re-PREP your application program
enough DL area space. with a larger MAXDATA parameter.
041 Internal error: DLSIZE Stack size or MAXDATA too small.
failed; the stack is Re-PREP your application program
frozen.
042 Formsfile name not The name of the forms file to
passed to VOPENFORMF. be opened must be included in the
call to VOPENFORMF.
043 Comarea length may not The Comarea length as specified
be less than 60. by the item Comarealen must be
60 words for HP terminals and
85 words for data capture devices.
044 Comarea length is too large. The Comarea length as
specified by the item
comarealeng must not
be longer than the longest
length documented.
045 TERMINAL or FORMSFILE
has not yet been opened.
046 Unrecognized Comarea
language code passed.
050 Forms File open failed. FOPEN intrinsic failed. Check
(FSERR !) forms file name.
051 The file is not a Check the formfile parameter to
VPLUS Forms File. make sure the file name is correct.
052 Internal error: Forms FGETINFO intrinsic failed.
File FGETINFO failed.
(FSERR !)
053 Forms File probably Run FORMSPEC and compile the
hasn't been compiled. forms file.
(FSERR !)
060 The program supplied If you are using BASIC, check
COMAREA extension is too word 4 of COMAREA (USRBUFLEN),
small. and increase the length of the
COMAREA extension.
061 Internal error: Failure
to obtain required PASCAL
Heap area.
062 Internal error: Failure to
return PASCAL Heap area.
063 Failure to close Forms An error occurred while trying to close
File. (FSERR !) the forms file. Check that the forms file
is open before VCLOSEFORMF is called.
067 Invalid form store size A number outside the range of
specified. -1 to 255 is specified in the
FORM'STORE'SIZE variable, which
is the 39th word of the
VPLUS communication area.
068 VPLUS internal error; For languages other than BASIC,
there is not enough DL VPLUS uses the DL area
area space. as the COMAREA extension. See
error 040.
069 VPLUS internal See error 041.
error; the stack is
frozen.
9001 Native Language Support Check with System Manager to
software not installed. install Native Language Support
software.
9002 Language specified is not Select another language or check
configured on this system. with System Manager to configure
the desired language.
9500 Language of forms file is See System Manager to configure
not configured on this the language or use forms files
system. on a system with that language
configured.