HP 3000 Manuals HP 3000 Manuals
SNA NRJE/V and SNA NRJE/iX Configuration
JES2 Requirements (SNA NRJE)
The JES2 configuration consists of defining the remote workstation to
JES2 in a configuration file. JES2 requires (either specifically or by
default) that the following information be defined for each workstation:
* JES2 global parameters
* LINEnnnn--line definition
* RMTnnnn--remote workstation definition
* Rnnnn.PRm--remote printer definition
* Rnnnn.PUm--remote punch definition
* Rnnnn.RDm--remote reader definition
Table 2-1 contains the parameters and values required by Hewlett-Packard
for SNA NRJE for JES2 version 4.1 and earlier versions. For programmers
experienced in configuring 8100 DPPX/RJE workstations and 3770
workstations, the table provides most of the needed information. For
more information, see the parameter descriptions at the end of this
chapter.
Table 2-1. SNA NRJE: JES2 Parameters
----------------------------------------------------------------------------------
| | | |
| Pre-version 4.1 | Version 4.1 Parameters | Comments |
| Parameters | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| LINEnnnn macro | | |
| | | |
- - - -
| UNIT=SNA | UNIT=SNA | Required. |
| | | |
- - - -
| RMTnnnn macro | | |
| | | |
- - - -
| LUTYPE1 | DEVTYPE=LUTYPE1 | Required. |
| | | |
| LUNAME | LUNAME | Do NOT specify. |
| | | |
| BUFSIZE=256 or | BUFSIZE=256 or | |
| | | |
| BUFSIZE=512 | BUFSIZE=512 | Required. |
| | | |
| CONSOLE | CONS=YES | Required. |
| | | |
| NOCMPCT | COMPACT=NO | Required. |
| | | |
| NUMRDR | NUMRDR | Required (specify from |
| | | 1-7). |
| | | |
| SETUPHDR | SETUP=PDIR | Required. |
| | | |
| SETUPINF | LOCAL190=INFO | Required. |
| | | |
| WAITIME=1 | WAITIME=1 | Required. |
| | | |
----------------------------------------------------------------------------------
Table 2-1. SNA NRJE: JES2 Parameters (cont.)
----------------------------------------------------------------------------------
| | | |
| Pre-version 4.1 | Version 4.1 Parameters | Comments |
| Parameters | | |
| | | |
----------------------------------------------------------------------------------
| | | |
| | | |
| Rnnnn.PRm macro | | |
| | | |
- - - -
| AUTO | | Required for Ver. 1.3.2 |
| | | and earlier. |
| | | |
| CCTL | CCTL=YES | Required. |
| | | |
| CMPCT/NOCMPCT | COMPACT=NO/YES | Do NOT specify. |
| | | |
| COMP/NOCOMP | COMPRESS=NO/YES | Do NOT specify. |
| | | |
| START | START=YES | Required. |
| | | |
| FCBLOAD/NOFCBLOAD | FCBLOAD=YES/NO | Do NOT specify. |
| | | |
| LRECL | LRECL | If specified, must be |
| | | between 40 and 255. |
| | | |
| PRWIDTH | PRWIDTH | Required (value must be |
| | | between 40 and 255). |
| | | |
| SELECT | SELECT | Do NOT specify. |
| | | |
| SEP | SEP | Required. |
| | | |
| UCS=O | UCS=O | Required. |
| | | |
| Rnnnn.PUm macro | | |
| | | |
- - - -
| AUTO | | Required for Ver. 1.3.3 |
| | | and earlier. |
| | | |
| CCTL | CCTL=YES | Required. |
| | | |
| CMPCT/NOCMPCT | CMPCT=YES/NO | Do NOT specify. |
| | | |
| COMP/NOCOMP | COMPRESS=YES/NO | Do NOT specify. |
| | | |
| START | START=YES | Required. |
| | | |
| SELECT | SELECT | Do NOT specify. |
| | | |
| SEP | SEP | Required. |
| | | |
- - - -
| Rnnnn.RDm macro | | |
| | | |
- - - -
| START | START | Required. |
| | | |
----------------------------------------------------------------------------------
JES3 Requirements (SNA NRJE)
The JES3 configuration consists of defining the remote workstation to
JES3 in a configuration file. JES3 requires (either specifically or by
default) that the following information be defined for each workstation:
* JES3 global parameters
* CONSOLE--remote workstation console
* DEVICE--to define printers and punches
* RJPWS--remote workstation definition
JES3 macro and operand values for SNA NRJE should be coded as though a
DPPX/RJE 8100 SNA workstation were being installed. Table 2-2 contains
the parameter and values required by Hewlett-Packard for SNA NRJE. For
more information, see the parameter descriptions at the end of this
chapter.
Table 2-2. SNA NRJE: JES3 Parameters
-------------------------------------------------------------------------------
| | |
| Parameters | Comments |
| | |
-------------------------------------------------------------------------------
| | |
| CONSOLE macro | |
| | |
- - -
| JNAME | Required. |
| | |
| TYPE=RJP | Required. |
| | |
- - -
| DEVICE macro | |
| | |
- - -
| DTYPE=RMTxxxxx | Required. |
| | |
| JNAME | Required. |
| | |
- - -
| RJPWS macro | |
| | |
- - -
| N | Required. |
| | |
| RD | Required (specify from 1-7). |
| | |
| C=R | Required. |
| | |
| COMPACT=NO | Required. |
| | |
| AUTO=N | Required. |
| | |
| LU | Do NOT specify. |
| | |
-------------------------------------------------------------------------------
VSE/POWER Requirements (SNA NRJE)
The VSE/POWER configuration consists of defining the remote workstation
to VSE/POWER in a configuration file. VSE/POWER requires (either
specifically or by default) that the following information be defined for
each workstation:
* VSE/POWER global parameters
* PRMT--remote workstation definition
VSE/POWER macro and operand values for SNA NRJE should be coded as though
a DPPX/RJE 8100 SNA workstation were being installed. Table 2-3 contains
the parameters and values required by Hewlett-Packard for SNA NRJE. For
more information, see the parameter descriptions at the end of this
chapter.
Table 2-3. SNA NRJE: VSE/POWER Parameters
-------------------------------------------------------------------------------
| | |
| Parameters | Comments |
| | |
-------------------------------------------------------------------------------
| | |
| POWER | Subparameter SNA=(,,POWER) is required. |
| | |
- - -
| PRMT macro | |
| | |
- - -
| CONSOLE=YES | Required. |
| | |
| REMOTE | Required. |
| | |
| SESSLIM=6 | Required. |
| | |
| TYPE=LUT1 | Required. |
| | |
| XLATE=NO | Required. |
| | |
| CMPACT | Do NOT specify. |
| | |
| LU | Do NOT specify. |
| | |
-------------------------------------------------------------------------------
NOTE Parameters that are not listed in table 2-3 can be entered at your
discretion. There are no restrictions on them beyond what is
required for DPPX/RJE on the IBM 8100.